3-069-935-11 (1) DCR-IP7/IP7BT/ PC120/PC120BT Network Function Operating Instructions Registration code © 2001 Sony Corporation
On trademarks •ImageStation is the registered trademark of Sony Corporation. •“Memory Stick” and are the registered trademarks of Sony Corporation. •The BLUETOOTH trademarks are owned by their proprietor and used by Sony Corporation under license. •NetFront by Access Co., Ltd. is adopted for the Internet function of this product. NetFront is registered trademark of Access Co., Ltd in Japan. Copyright © 1996 – 2000 ACCESS CO., LTD.
Table of contents 3
– Introduction – Network function on the camcorder The camcorder can access the Internet through your provider by a dial-up networking connection with a Bluetooth device, and view a Web page, send and receive e-mail with images attached to it. Bluetooth specification ver. 1.1 is adopted for the communication system of the camcorder, and Compatible Bluetooth profiles are “Generic Access Profile” and “Dial-up Networking Profiles.
Network function on the camcorder • Making your album on the Web You can upload images to your album, and view or edit your album. • Easy network preferences (Sony Style Connect) Using “Sony Style Connect,” you can easily set the Internet and e-mail preferences. Once you make the DI customer registration, you can get your DI customer ID and password. Entering your DI customer ID, password, and telephone number of an access point, you can access the Internet right away.
Network function on the camcorder Before using the network function Check that the procedure for using the network function following the flowchart below.
Network function on the camcorder Required procedures list 7
Overview of the Bluetooth wireless technology What is the Bluetooth wireless technology? The Bluetooth wireless technology allows communication between various Bluetooth devices without using cables. Devices which can use this technology include PCs, computer peripheral devices, PDAs, and mobile phones. This omnidirectional communication system enables communication even if the Bluetooth devices is in a bag or there are obstacles between the devices.
Basic operations in the NETWORK mode This section describes basic control ways to operate the camcorder, which are used for the network operations. How to use the Network Menu To access the Network Menu, refer to the section “Accessing to the network” in the operating instructions supplied with your camcorder. [a]: Send and receive e-mail. For details, see “Using e-mail” on page XX. [b]: Upload the images to your album on the Web and post the images on the Internet.
Basic operations in the NETWORK mode How to use the control button Most of the network operations are carried out by the control button. Select a button on the screen using the control button, then enter it by pressing the control button. Note The shape of the control button differs depending on your camcorder model. (1) Press v/V/b/B on the control button repeatedly to select the desired button displayed on the screen. The selected button turns orange.
Basic operations in NETWORK (2) Select either of the character type tab. ROMAN: When inputting alphabetical characters. 123: When inputting numerical characters. When selecting ROMAN When selecting 123 2 Inputting characters (1) Select the key which has the character you want to input. (2) Press the center z on the control button to enter it. Pressing it repeatedly selects the other characters on the key.
Basic operations in NETWORK To add a character Select [<] or [,]. Each time you press the center z on the control button, the cursor is moved to the left or right. Move the cursor at the position you want to add a character, then input characters. To start a new line Select [ ], then execute it. E.g., Enter “Hello” into the Subject item on the Send screen (1) Select the abc tab. (2) Select [ghi], then press the center z on the control button five times. “H” is entered.
Basic operations in NETWORK (5) Select [ ], then execute it. The cursor moves to the next position. (6) Select [jkl], then press the center z on the control button three times. “l” is entered. (7) Select [mno], then press the center z on the control button three times. “o” is entered. (8) Select [enter], execute it. “Hello” is entered and the Send screen appears again.
Basic operations in NETWORK The available characters list Alphabetical characters Key Character abc a t b t c t A t B t C t a t... def d t e t f t D t E t F t d t... ghi g t h t i t G t H t I t g t... jkl j t k t l t J t K t L t j t... mno m t n t o t M t N t O t m t... pqrs p t q t r t s t P t Q t R t S t p t... tuv t t u t v t T t U t V t t t... wxyz w t x t y t z t W t X t Y t Z t w t... Symbol characters Key Character . ',?! . t ' t , t ? t ! t . t... @/~\^ @ t / t ~ t \ t ^ t @ t.
Basic operations in NETWORK Numerical characters Key Character 0 0 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 How to use the toolbar on the browser When you access the Internet and view a Web page, you can make various operations using the toolbar. While the browse screen is displayed, press BROWSER MENU on the camcorder to display the toolbar. For details on BROWSER MENU, refer to the operating instructions of the camcorder. To show the toolbar (1) Press BROWSER MENU on the camcorder.
Basic operations in NETWORK The buttons on the toolbar The buttons on the upper stage Button Function (Previous Page) Go to the previous page in your step (Next Page) Go to the next page in your step (Reflesh) Refresh the current page Use this button when images or characters on the Web page are not displayed properly. (Stop) Stop loading the current page (New URL) Jump to another page (Bookmark) Bookmark the current page (Bookmarks are stored in the camcorder.
– Preparation – Registering a Bluetooth device This section describes making a registration with a Bluetooth device. Here describes the procedure when registering the Sony Modem Adaptor with Bluetooth Function. Once the registration is made, the camcorder can connect with the Bluetooth device without deleting its registration. Up to three Bluetooth devices can be registered. Also, refer to the operating instructions supplied with the Bluetooth device.
Registering a Bluetooth device (2) Select [ Setup], then execute it. The Setup screen appears. (3) Select [Bluetooth Setup], then execute it. The Bluetooth Setup screen appears. (4) Select [Select], then execute it. The Bluetooth devices list appears. When making a registration for the first time, only [Return] and [New] are indicated. The list shows up to three Bluetooth devices.
Registering a Bluetooth device (6) Select the desired Bluetooth device, then execute it. The character input screen appears. (7) Enter the pass key. For details on how to input characters, see “How to input characters” on page XX. E. g., When using the BTA-NW1 Modem Adaptor with Bluetooth Function, the pass key is its serial number which is indicated on the label on the rear panel. ® MODEL NO.
Registering a Bluetooth device (10) Select [Exit], then execute it. The Network Menu appears again. When the registration was failed Carry out the procedure “When using the Modem Adaptor with Bluetooth Function ” on page xx again from step 4. Displaying self information You can display your camcorder information. (1) Open the Network Menu. For details on how to open the Network Menu, refer to the section “Accessing to the network” in the operating instructions supplied with your camcorder.
Registering a Bluetooth device To clear the Self Information Select [Return], then execute it. Radio wave indication indicates a radio wave condition with the connected Bluetooth device. (Use this indication as a guide.) Deleting the registered Bluetooth device from the list Up to three Bluetooth devices can be registered on the camcorder. When deleting the Bluetooth device from the list, follow the procedure below. (1) Open the Network Menu.
Registering a Bluetooth device (4) Select [Select], then execute it. The Bluetooth devices list appears. (5) Select the device you want to delete, then execute it. The device name and address of the selected device are indicated. (6) Select [Delete], then execute it. The selected device is deleted from the list.
Customer registration DI customer registration Once you make a DI customer registration (Digital Imaging customer registration), you can XXXXX You can make a DI customer registration one of the following ways: 1 Online registration though the Web site for DI customer registration 2 Online registration using the supplied CD-ROM 3 Online registration though the camcorder For making an online registration through the camcorder, the private line will be used.
Customer registration (2) Select [ Setup], then execute it. The Setup screen menu appears. (3) Select [Online Registration], then execute it. The screen for verifying the connection appears. Select [OK], then execute it. The camcorder starts connecting to the site. Once the connection is completed, the online registration screen appears. Set the Bluetooth device to connection standby with the camcorder beforehand.
Internet service provider To access the Internet, you have to sign-up with an internet service provider (ISP). The provider is as an intermediary between your camcorder and the Internet. After you sign-up a provider; you can view various Web pages through the Internet, you can send and receive e-mail by using your e-mail address. The e-mail address is a destination address in e-mail transmission. Also, various services may be available depending on a provider.
Registering with “Sony Style Connect” You can make a online registration with “Sony Style Connect” using the camcorder. You can also sigh-up with R-net during the registration.
Registering with “Sony Style Connect” 27
Making a registration for your album on the Web 28
Making a registration for your album on the Web 29
Setting network preferences You have to access the Internet to make your album on the Web, view a Web page, or send or receive your e-mail. This section describes how to set network preferences to access the Internet. Entering your customer ID and password Enter your customer ID and password you obtained by the DI customer registration. This setup is required for making your album on the Web. (1) Open the Network Menu.
Setting network preferences (6) Select [Enter], then execute it. The Network Setup screen appears again. (7) Select [Password], then execute it. The character input screen appears. (8) Enter your password. For details on how to input characters, see “How to input characters” on page XX. Note When you check the item “Verify Password” in the Network Options screen, you cannot enter your password.
Setting network preferences Setting your provider preferences When using “Sony Style Connect,” carry out the following procedures: “1 Selecting your provider type” on page xx, “2 Entering telephone numbers of your access points” on page xx, and “4 Setting other preferences” on page xx. When using other providers, carry out the following procedures: “1 Selecting your provider type” on page xx, “3 Setting your provider preferences manually” on page xx, and “4 Setting other preferences” on page xx.
Setting network preferences 2 Select [Setting], then execute it. The Provider Setting: Sony Style Connect screen appears. Go to “2 Entering telephone numbers of your access points” on page XX. When using other providers: 1 Select [Custom], then execute it. a is checked and changs to . 2 Select [Setting], then execute it. The Provider Setup: Custom screen appears. Go to “3 Setting your provider preferences manually” on page XX.
Setting network preferences (2) Enter the telephone number of your access point. For details on how to input characters, see “How to input characters” on page XX. (3) Select [Enter], then execute it. The Provider Setting: Sony Style Connect screen appears again. Tip You can also register the telephone numbers of access points into [TEL2] and [TEL3]. If necessary, enter the numbers into [TEL2] and [TEL3]. (4) Select [OK], then execute it. The telephone numbers registration is complete.
Setting network preferences Tip on dial-up connection The dial-up connection is to access the Internet using a phone line. DNS1: Enter the DNS (Domain Name System) server address of your provider. Tips on “DNS1” • This “DNS1” is also referred to as a “name server,” “primary DNS server,” “primary name server,” etc. • This entry is unnecessary depending on the provider. For details, consult your provider. DNS2: Enter the secondary DNS server address of your provider, if necessary.
Setting network preferences SMTP Server: Enter the SMTP (Simple Mail Transfer Protocol) server address of your provider. The SMTP server is for sending e-mail. Tip on “SMTP Server” This “SMTP Server” is also referred to as a “mail server,” “SMTP mail server,” etc. The SMTP server is the same as the POP server depending on the provider. POP Server: Enter the POP (Post Office Protocol) server address of your provider. The POP server is for receiving e-mail.
Setting network preferences (2) Select [Network Options], then execute it. The Network Options screen appears. (3) Set up the following items: Verify Password: Select whether the password entry is required when you access your provider. When you check this item, you have to enter your DI customer ID password or password for accessing your provider each time you try to make a connection.
Setting network preferences Image Display: Select whether to display images on the screen when viewing a Web page. This item is checked at the factory. Reset: Reset all the items on the Network Options screen except “Signature” and “Modem Init.” Note The screen for verification does not appear when you try to reset items. Modem Init: Set up the character sting of the modem initialization. If no setup is specified, you need not to modify this item. (4) Select [Exit], then execute it.
— Network Operation— Making your album on the Web You can upload still or moving images to your album on the Web through the Internet and post the images on your album. The album on the Web is provided with “ImageStation.” You can make the image album on the Web as the simplified Web page and send an invitation card to invite your friends to your album. You can also access your album on the Web using your computer.
Making your album on the Web (2) Select [ Album], then execute it. The Album screen appears. (3) Select [ Upload], then execute it. The Web Album – Upload screen appears. (4) Select [Album No.], then execute it. The album list page appears. (5) Select the desired album, then execute it. Selecting the album is complete. The number of prepared albums There are 10 albums (ALBUM 01 to 10).
Making your album on the Web 2 Selecting images to upload Next, select the images to upload. (1) Select [ImageSelect], then execute it. The image index list appears. (2) Select the desired images. Move the yellow arrow mark onto the image you want to upload, then press the control button. The selected image is indicated by the checkmark ( ). To page up or down the image index list Select [<] or [,], then execute it. The next or previous page is displayed.
Making your album on the Web 3 Sending an invitation card Select the addressee to send the invitation card. (1) Select [Invitation], then execute it. The Album: Invitation screen appears. (2) Select [To], then execute it. The address list appears. The list shows the destination addresses that are registered on the address book. For details on the address book, see “Using the address book” on page XX. When you select the address listed on it, go to step 6.
Making your album on the Web (5) Select [Enter], then execute it. The Album: Invitation screen appears again. The new e-mail address is listed and its check box is indicated by the checkmark ( ). (6) If you send the invitation card to other addresses, select other e-mail addresses, then execute it. The check box of the selected e-mail address is indicated by the checkmark ( ). (7) Select [@ Return], then execute it. The Album: Invitation screen appears again.
Making your album on the Web The list shows the messages that were entered. When you select the message listed on it, select it from the list. When you use the selected text, select [OK], then execute it. After you select the message, go to “5 Uploading images” on page XX. When you modify the selected text, select [Edit], then execute it. The character input screen appears. Go to step 3. (2) Select [@ New], then execute it. The character input screen appears. (3) Enter the text.
Making your album on the Web 5 Uploading images (1) Select [Send], then execute it. The screen for verifying the connection appears. (2) Check the telephone number. When dialing to other telephone numbers Select [TEL No.], then execute it. The registered telephone number list appears. Select the desired telephone number, then execute it. The selected telephone number is specified. (3) Select [Connect], then execute it. The camcorder starts dialing to the selected telephone number.
Making your album on the Web Viewing or editing images of your album on the Web You can view or download images of your album on the Web. 1 Viewing images (1) Open the Network Menu. For details on how to open the Network Menu, refer to the section “Accessing to the network” in the operating instructions supplied with your camcorder. Album], then execute it. (2) Select [ The Album screen appears. View/Edit], then execute it.
Making your album on the Web (5) Select [Connect], then execute it. The camcorder starts dialing to the selected telephone number. After the connection is completed, the album list page appears. (6) Select the album number that the image you want to view or edit is stored, then execute it. The index page appears. (7) Select the desired image, then execute it. The image is enlarged to fill the screen.
Making your album on the Web (2) Check the number of images and the total file size. When selecting single image When selecting several images To cancel the downloading images Select [Cancel], then execute it. (3) Select [OK], then execute it. The message “Downloading” appears. After the downloading is completed, the message “Download Complete” appears. (4) Select [OK], then execute it. The index page or single-image screen appears.
Making your album on the Web When selecting images from the index page (1) Select the check box of the desired image, then execute it. The check box is indicated by the checkmark ( ). (2) When you select other images, repeat step 1. (3) Select [ Download], then execute it. The screen for verification appears. Set the Bluetooth device to connection standby with the camcorder beforehand. For details, refer to the operating instructions supplied with the Bluetooth device.
Making your album on the Web (2) When selecting another image, select [ it. Previous] or [ Next], then execute (3) Select [ Download], then execute it. The screen for verification appears. To return to the index page Select [Index Page], then execute it. Deleting images from the album You can delete the images from the album. When deleting the image displayed on the index page You can select several images and delete them at once.
Making your album on the Web Finishing viewing or editing the album To finish viewing or editing the album, and disconnect the phone line (1) Press BROWSER MENU on the camcorder to display the toolbar. (2) Select @ (Exit), then execute it. The album is exitted, then the line is disconnected. To only disconnect the phone line Select (Line Close), then execute it. Only the phone line is disconnected.
Using e-mail This section describes the basic usage of e-mail. E-mail is send and received via the Internet. E-mail is very convenient; you can send e-mail anytime, and its e-mail has been sent in a moment, you can also send images stored in a “Memory Stick” by attaching them to e-mail. Sending e-mail By entering the destination e-mail address, you can send e-mail in a moment. 1 Specifying the destination address Be careful to enter the address correctly.
Using e-mail Tips • The last-used address is listed next to New. • Addresses are listed in the historical order. (4) Select [New], then execute it. The character input screen appears. (5) Enter the e-mail address of an addressee. For details on how to input characters, see “How to input characters” on page XX. (6) Select [Enter], then execute it. The Send screen appears again. The new e-mail address is listed and its check box is indicated by the checkmark ( ).
Using e-mail (8) Select [Return], then execute it. The Send screen appears again. Note If you try to send the e-mail message with 50 addresses registered on the address book, the latest-used address will be deleted. The message “Address Book Full Overwrite the Data with Current Address?” appears for verification. When you overwrite it, select [OK], then execute it. When you select [Cancel], delete the unnecessary address from the address book, then enter a new address.
Using e-mail (4) Select [Enter], then execute it. The Send screen appears again. 3 Entering the text of a message Enter the text of the message. You can select the text from the message list, or modify it to use. The list shows up to six messages. (1) Select [Message], then execute it. The message list appears. The list shows the messages that were entered. When you use the selected text, select [OK], then execute it.
Using e-mail (4) Select [Enter], then execute it. The Send screen appears again. 4 Sending e-mail Tip You can send the e-mail message with your signature. For details, see “Attaching your signature to the message” on page XX. (1) Select whether you attach images or not. When attaching images, see “Attaching images to e-mail” on page XX. (2) Check the message. When you check or modify the message, see “Checking or modifying the message” on page XX. (3) Select [Send], then execute it.
Using e-mail (6) Select [OK], then execute it. The Send screen appears again. To cancel sending e-mail During sending, select [Cancel], then execute it. Tip You can check the e-mail inbox after sending e-mail. For details, see “4 Setting other preferences” on page XX. Checking or modifying the message (1) Display the Send screen. (2) Select [Message], then execute it. The message list appears. (3) Select the message you want to check or modify, then execute it.
Using e-mail (5) Select [Edit], then execute it. The character input screen appears. (6) Modify the message. For details on how to input characters, see “How to input characters” on page XX. (7) Select [Enter], then execute it. The Send screen appears again. Attaching images to e-mail You can send images by attaching them to e-mail. Preparation Store the desired images in the “Memory Stick” and insert it into the camcorder.
Using e-mail (3) Select the desired images. Move the yellow arrow mark onto the image you want to upload, then press the control button. The selected image is indicated by the checkmark ( ). To page up or down the index list Select [<] or [,], then execute it. The next or previous page is displayed. (4) Repeat step 3 to select other images. Note The total number of images is 99, and the total file size is up to 3 MB. (5) Select [@ OK], then execute it. The Send screen appears again.
Using e-mail (1) Open the Network Menu. For details on how to open the Network Menu, refer to the section “Accessing to the network” in the operating instructions supplied with your camcorder. Setup], then execute it. (2) Select [ The Setup screen appears. (3) Select [Network Options], then execute it. The Network Options screen appears. (4) Select [Signature], then execute it. The character input screen appears. (5) Enter your signature.
Using e-mail (6) Select [Enter], then execute it. The setup of your signature is completed, and the Network Options screen appears again. “Yes” is indicated next to [Signature]. (7) Select [Exit], then execute it. The Setup screen appears again. (8) Select [Exit], then execute it. The Network Menu appears again. Using the address book Once you register the frequently used e-mail addresses on the address book, you can send e-mail without entering the e-mail address.
Using e-mail (3) Select [New], then execute it. The Address Book: New screen appears. (4) Select [Name], then execute it. The character input screen appears. (5) Enter the destination name. For details on how to input characters, see “How to input characters” on page XX. Note The total number of characters you can enter in the [Name] box is up to 24. (6) Select [Enter], then execute it. The Address Book: New screen appears again.
Using e-mail (9) Select [Enter], then execute it. The Address Book: New screen appears again. (10) Select [Return], then execute it. The Address screen appears again. (11) Select [Exit], then execute it. The Network Menu appears again. Tips •The addresses are listed in alphabetical order. •When you reply to the received address, the address will be automatically registered on the Addressbook. To edit the address, see “Editing the address book” below.
Using e-mail (3) Select [Name] or [Address], then execute it. When modifying the name, select [Name], and when modifying the address, select [Address]. The character input screen appears. (4) Modify the name or address. For details on how to input characters, see “How to input characters” on page XX. (5) Select [Enter], then execute it. The Address screen appears again. (6) Select [Return], then execute it. The Address screen appears again.
Using e-mail Selecting the destination address from the address book You can select the destination address from the address book. (1) Follow steps 1 to 3 in “Registering destination addresses on the address book” on page XX. The Address screen appears. (2) Select the area that the name and address are indicated, then select the destination address using the control button b/B. (3) Select [To], then execute it. The Send screen appears.
Using e-mail (1) Open the Network Menu. For details on how to open the Network Menu, refer to the section “Accessing to the network” in the operating instructions supplied with your camcorder. Mail], then execute it. (2) Select [ If the Receive screen is not displayed, select the Receive tab. The Receive screen appears. (3) Select [Receive], then execute it. The screen for verifying the connection appears.
Using e-mail (6) When an e-mail message is received, select the area that the message is displayed, then select the message using the control button b/B, then execute it. The message is displayed. (7) Select [Return], then execute it. The Receive screen appears again. To cancel receiving e-mail During receiving, select [Cancel], then execute it. Incoming E-mail not received remains in your server.
Using e-mail Tips •You can check the e-mail inbox after sending e-mail. For details, see “4 Setting other preferences” on page XX. •You can skip e-mail if its file size is too large. For details, see “4 Setting other preferences” on page XX. •As for a received e-mail, the total number of characters used for the subject and the sender name has an upper limit of 24 characters. When you receive such an e-mail, you cannot read the subject and the sender name on the camcorder.
Using e-mail (5) Carry out the procedure from step 3 in “4 Sending e-mail” on page XX. Forwarding the message to another person – Forward You can forward the received message to another person. (1) Display the Receive screen. (2) Select the area that a message is indicated, then select the message you want to forward using the control button b/B, then execute it. The selected message is displayed. (3) Select [Forward], then execute it. The Send screen appears.
Using e-mail Deleting e-mail Up to 50 received e-mail messages can be stored in a “Memory Stick.” If you try to receive a 51th e-mail message, the error message appears and the camcorder cannot receive the e-mail message. Preparation •Insert the “Memory Stick” into the camcorder, which stores e-mail. •Release the lock of the “Memory Stick.” (1) Open the Network Menu.
Using e-mail (5) Select [OK], then execute it. The selected e-mail message is deleted. To cancel deleting Select [Cancel], then execute it in step 5.
Viewing Web pages A site that posts information on the Internet is called a “Home Page” or “Web site.” You can easily retrieve information by accessing a Web site on the Internet. Viewing Web pages 1 Entering URL to access the Web page Enter the address of the Web page, and connect to the Internet. Be careful to enter the address correctly. Tip on URL A Web site has its unique address on the Internet. The address is called a URL. This is required to access a Web site. (1) Open the Network Menu.
Viewing Web pages (5) Select [Enter], then execute it. The screen for verifying the connection appears. Set the Bluetooth device to connection standby with the camcorder beforehand. For details, refer to the operating instructions supplied with the Bluetooth device. (6) Check the telephone number. When dialing to other telephone numbers Select [TEL No.], then execute it. The registered telephone number list appears. Select the desired telephone number, then execute it.
Viewing Web pages Notes •When the address is too long to display it, the whole of the address is not indicated. If you want to know the correct address of the page, select , then execute it. •All of the page is not displayed on the screen. •It takes more time to load the page that has lots of images ,and its images or text may not be displayed properly. This is not a malfunction. •When viewing the scaled-down page, the screen may be caused some flicker or the color may be strange. This is not a malfunction.
Viewing Web pages To edit the bookmark You can edit the title of a bookmark. (1) Select (Bookmark), then execute it. The bookmark list appears. (2) Select the bookmark you want to edit, then execute it. The title and URL are indicated. (3) Select [Edit], then execute it. The character input screen appears. (4) Edit the name. For details on how to input characters, see “How to input characters” on page XX. (5) Select [Enter], then execute it.
Viewing Web pages To delete bookmarks You can delete bookmarks. We recommend that you delete unnecessary bookmarks since you can store up to 30 bookmarks . (1) Select (Bookmark), then execute it. The bookmark list appears. (2) Select the bookmark you want to delete, then execute it. (3) Select [Delete], then execute it. The message “Delete This Bookmark?” for verification appears. (4) Select [OK], then execute it. The selected bookmark is deleted.
Viewing Web pages 3 Jumping to the Web page specified by the bookmark (1) When the toolbar is not displayed, press BROWSER MENU on the camcorder. The toolbar appears. (Bookmark), then execute it. (2) Select The bookmark list appears. (3) Select the bookmark, then execute it. (4) Select [Go], then execute it. Set the Bluetooth device to connection standby with the camcorder beforehand. For details, refer to the operating instructions supplied with the Bluetooth device.
Viewing Web pages Storing the Web page into a “Memory Stick” – Page Memo You can store the desired Web pages in a “Memory Stick.” Once you store them, you can view the Web page without accessing the Internet. Storing the Web page into a “Memory Stick” Preparation •Insert the “Memory Stick” for storing images into the camcorder. •Release the lock of the “Memory Stick.” (1) Display the Web page you want to store. (2) When the toolbar is not displayed, press BROWSER MENU on the camcorder.
Viewing Web pages Editing the title of a page memo You can edit the title of a page memo stored in a “Memory Stick.” Preparation •Insert the “Memory Stick” into the camcorder, which is for storing images. •Release the lock of the “Memory Stick.” (1) Select (Page Memo), then execute it. The page memo list appears. (2) Select the page memo you want to edit, then execute it. The title and URL of the selected page memo are indicated. (3) Select [Edit], then execute it.
Viewing Web pages (6) Select [Return], then execute it. The page memo list appears again. (7) Select [Return], then execute it. The browser screen appears again. To delete the page memo You can delete page memos. We recommend that you delete unnecessary page memos since you can store up to 30 bookmarks . Preparation •Insert the “Memory Stick” into the camcorder, which is storing page memos. •Release the lock of the “Memory Stick.” (1) Select (Page Memo), then execute it.
Viewing Web pages (4) Select [OK], then execute it. The selected page memo is deleted and the page memo list appears again. (5) Select [Return], then execute it. The browser screen appears again. To cancel deleting a page memo Select [Cancel], then execute it in step 4. Displaying the Web page stored in page memo (1) Select (Page Memo), then execute it. The page memo list appears. (2) Select the page memo you want to display its page. (3) Select [Open], then execute it.
Viewing Web pages Exitting the browser To finish viewing the Web page, and disconnect the phone line (1) Press BROWSER MENU on the camcorder to display the toolbar. (2) Select @ (Exit), then execute it. The browser is exitted, then the phone line is disconnected. To only disconnect the line Select (Line Close), then execute it. The phone line is disconnected. Note When exitting the browser, the message for verification may appear depending on your camcorder.
– Additional Information – File storage destinations and file names You cannot this page on the camcorder. The meanings of the file names are as follows. sssss stands for any number within the range from 00001 to 99999. ssss stands for any number within the range from 0001 to 9999. XXX stands for a portion of an attached file name.
Troubleshooting 84
Troubleshooting 85
Troubleshooting 86
Specifications Bluetooth Available number of registered devices 3 Album on the Web The number of albums 10 The maximum number of uploaded images at one time 99 The maximum file size of uploaded images at one time 3 MB Browser The available number of bookmarks 30 The maximum number of page memos recordable in a “Memory Stick” 30 E-mail Sending The registrable number of subjects 6 The maximum number of characters of a subject 24 The registrable number of messages 6 The maximum number of characters of a mess
Messages Various messages appear on the screen. Check the corresponding descriptions in the following list. General Message Meaning Connection Error No Device Found • The Bluetooth device is too far from the camcorder. • The Bluetooth device is busy. Bluetooth Confirmation Error Check The Certified Status Register the Bluetooth device again. Bluetooth Registration Error Check The Passkey • The pass key was wrong. • The pass key transmission was failed.
Messages Message Meaning Enter Password for DI Customer ID For details on “Verify Password,” see “3 Setting other preferences” (p. XX). Enter PPP Password Ending Saving The Profile Do not turn off the camcorder while the message is indicated. Album on the Web Message Meaning Album Server Disconnected Operate again after a while. Timeout Upload Canceled Upload Error Outgoing Mail Error Select Pictures Select the image or set up the invitation card before uploading (p. XX).
Messages Browser Message Meaning You Are About to View You try to open an SSL page. When you know that the page is safe, Pages Over a Secure Connection select [OK], then execute it. Do You Want To Continue? You Are About to Leave a Secure Internet Do You Want to Continue? Warrant Date Expired Invalid Data Open Anyway? Set The Date and Time Invalid Data Open Anyway? The clock is not set up on the camcorder. Set up the clock.
Error codes Error code/Message Cause Corrective Actions 1000 XXX User authentication failed. Check your DI customer ID and password, then connect to the album. 1001 XXX No specified album on the sever. Select the album again, then connect the album. 1002 XXX Your registration on the album not complete. Make an album registration XXXXXX 1003 XXX File save failed. Send the image again. 1004 XXX Wrong e-mail address. Check your e-mail address entered, then send the invitation card.
Glossary 92
Glossary 93
Setup memo XXX XXX Network Setup DI Customer Setup ID Password Provider Setup Sony Style Connect TEL1 TEL2 TEL3 Custom PPP ID Password DNS1 DNS2 TEL No.
Sony Corporation Printed in Japan 3 0 6 9 9 3 5 1 1
