Operating Instructions
Table Of Contents
- Before you begin
- Getting started
- Basic operations
- Advanced operations
- Using alternative power sources
- Changing the mode settings
- Photo recording
- Shooting with all the pixels ﾐ PROG. SCAN
- Using the FADER function
- Shooting with backlighting
- Using the wide mode function
- Enjoying picture effect
- Recording with various effects ﾐ digital effect
- Shooting with manual adjustment
- Using the PROGRAM AE function
- Focusing manually
- Interval recording
- Cut recording
- Superimposing a title
- Making a custom title
- Labeling a cassette
- Watching on a TV screen
- Viewing the picture with the picture effect
- Viewing the picture with the digital effect
- Searching the boundaries of recorded tape with date ﾐ date search
- Searching the boundaries of recorded tape with title ﾐ title search
- Searching for a photo ﾐ photo search/photo scan
- Returning to a pre-registered position
- Displaying recording data ﾐ data code function
- Editing onto another tape
- Editing partially on a mini DV tape ﾐ DV synchro-editing
- Recording from a VCR or TV
- Replacing recording on a tape ﾐ insert editing
- Audio dubbing
- Memory card slot operations
- Using the memory card slot ﾐ introduction
- Recording an image from a mini DV tape as a still image
- Copying still images from a mini DV tape ﾐ photo save
- Recording still images on PC cards (not supplied) ﾐ memory photo recording
- Viewing a still picture ﾐ memory photo playback
- Preventing accidental erasure ﾐ PROTECT
- Deleting images
- Copying the image recorded with the memory card slot to mini DV tapes
- Playing back images in a continuous loop ﾐ SLIDE SHOW
- Additional information
- Usable cassettes and playback modes
- Charging the vanadium-lithium battery in the camcorder
- Resetting the date and time
- Simple setting of clock by time difference
- Tips for using the battery pack
- Maintenance information and precautions
- Using your camcorder abroad
- Trouble check
- Self-diagnosis function
- Specifications
- Identifying the parts
- Warning indicators
- Index
125
Additional information
AC power adaptor
Charging
•Use only an “InfoLITHIUM” type battery pack.
•Place the battery pack on a flat surface without vibration during charging.
•The battery pack will get hot during charging. This is normal.
Others
•Unplug the unit from the wall outlet when not in use for a long time. To disconnect the
power cord, pull it out by the plug. Never pull the cord itself.
•Do not operate the unit with a damaged cord or if the unit has been dropped or damaged.
•Do not bend the AC power cord forcibly, or put a heavy object on it. This will damage the
cord and may cause a fire or an electrical shock.
•Be sure that nothing metallic comes into contact with the metal parts of the connecting
plate. If this happens, a short may occur and the unit may be damaged.
•Always keep the metal contacts clean.
•Do not disassemble the unit.
•Do not apply mechanical shock or drop the unit.
•While the unit is in use, particularly during charging, keep it away from AM receivers and
video equipment because it will disturb AM reception and video operation.
•The unit becomes warm while in use. This is normal.
•Do not place the unit in locations that are:
Extremely hot or cold, Dusty or dirty, Very humid, Vibrating
Note on dry batteries
To avoid possible damage from battery leakage or corrosion, observe the following.
•Be sure to insert the batteries in the correct direction.
•Dry batteries are not rechargeable.
•Do not use a combination of new and old batteries.
•Do not use different types of batteries.
•The batteries slowly discharge while not in use.
•Do not use a battery that is leaking.
If battery leakage occurred
•Wipe off the liquid in the battery case carefully before replacing the batteries.
•If you touch the liquid, wash it off with water.
•If the liquid get into your eyes, wash your eyes with a lot of water and then consult a
doctor.
If any difficulty should arise, unplug the unit and contact your nearest Sony dealer.
Maintenance information and precautions