For those who make a one-to-one connection between the MD DISCAM and your PC at home, click the desired step in the yellow area on the left-hand side of the screen. For those who connect the MD DISCAM to a PC on a LAN in your office or home, begin by choosing the desired step in the green area located on the right-hand side of the screen. For one-to-one connection between your MD DISCAM and your PC at home, follow the steps here. STEP1 Preparing for connection.
MD DISCAM is equipped with an Ethernet Terminal for the connectionto a PC. The one-to-one connection between the MD DISCAM and the PC requires an Ethernet Terminal on the PC as well. Q: Is your PC equipped with an Ethernet Terminal? Ethernet terminal Does your PC have the built-in Ethernet Terminal (Refer to the illustration on the left.)? Is an Ethernet Board or an Ethernet Card available? *The Ethernet Terminal looks quite similar to a modem terminal but is a little wider. Yes.
A commercially available LAN board or LAN card is required to add an Ethernet Terminal to the PC. If you have a desktop, install a LAN board to the PCI slot, refer to the instruction manual about its installation. If you have a laptop, insert a LAN card in the slot of your PC. Refer to the instruction manual of the LAN card about its installation. *Contact the manufacturer regarding the installation of the board or card.(The MD DISCAM will not provide customer support for the above devices.
After preparing the Ethernet Terminal, connect the MD DISCAM to your PC with the power off. A commercially available Cross Cable is necessary for connection. Connect one end to your MD DISCAM and the other to your PC. Q: What is the OS for your PC? Next, let's set your PC.
When you connect the MD DISCAM to your PC, you need to make Windows settings. 1. Open "Network" from the Control Panel. 2. The configuration window of "Network" appears. Select the built-in LAN board (the added board or card in the case of additional installation)and open "Properties". 3. The configuration window of "TCP/IP Properties" appears. Check "Specify an IP address" and set the following. IP Address:192.168.0.1 Subnet Mask:255.255.255.0 Now you have set your PC. Let's move on to the MD DISCAM.
After setting your PC, you need to set the MD DISCAM. 1. Select "ADVANCED" - "PC CONNECT" - "SET UP" from the menu of the MD DISCAM. 2. Select " Manual". Touching the white up-and-down arrows with the input pen or using the control dial and set the following. IP Address : 192.168.0.10 Net Mask : 255.255.255.0 Gateway : 0.0.0.0 3. Press "EXEC" and restart the MD DISCAM. 4. When the MD DISCAM restarts, select "ADVANCED" "PC CONNECT" - "CONNECT" from the menu. 5.
When the settings of the PC connection with the MD DISCAM have been completed, the home page address (http://192.168.0.10/) shown on the left appears on the screen. When it appears, let's view pictures and images on your PC. Type the URL shown on the screen of the MD DISCAM into the address column of Web browsers (Microsoft(R) Internet Explorer, Netscape(R)Navigator, etc.), just as you would do to browse ordinary home pages.
(*)Checking "Never dial a connection" of "Internet Options" will prevent this window from appearing. Such a setting, however, requires a manual connection to the desired Internet access point on "Dial-up Networking". Note! When you switch the connection of your PC to the MD DISCAM from the Internet, make sure to disconnect the Internet first and then connect your PC to the MD DISCAM. 1. Make sure that the Internet is disconnected first and then start the Web browser. 2.
When connecting the MD DISCAM to your PC, start the PC and make settings for the MacOS. 1.First, open APPLE MENU INTERNET ACCESS "Internet Setup Assistant". (Click here when "Internet Setup Assistant" is not installed.) 2. Would you like to set up your computer to use the internet? - Select "Yes". (Refer to the illustration on the left.) 3. Do you already have an Internet account? - Select "Yes". 4. Give a name to this setting. Give a desired name to the setting. It has been named "MD DISCAM" here.
When you connect your MD DISCAM to your PC, power and set up is as follows. 1. Open APPLE MENU - Control Panel - TCP/IP 2. Select "set up" from file menu. 3. Choose one of the settings you already have (we chose "internet" on the left.) and click "Duplicate...". 4. Then the dialogue box will open and you will be able to have it as you like. For example, we named "MD DISCAM" on the left. 5. Click"OK", select "MD DISCAM" and click "Make Active". 6. Chose the way "Ethernet" and will be done "manually". 7.
When your have completed settings of your PC, make settings of your MD DISCAM. 1. Select "ADVANCED" - "PC CONNECT" - "SET UP" from INDEX MENU of the MD DISCAM. 2. Select " Manual". Touching white up-and-down arrows with the input pen or using Control Dial, make settings as follows. IP Address : 192.168.0.10 Net Mask : 255.255.255.0 Gateway : 0.0.0.0 3. Press "EXEC" and restart the MD DISCAM. 4. When the MD DISCAM restarts, select "ADVANCED" "PC CONNECT" - "CONNECT" from the menu. 5.
When the settings of the PC connection of the MD DISCAM have been completed, the home page address (http://192.168.0.10/) shown on the left appears on the screen. When it appears, let's try to capture pictures and images to the PC. Type the URL shown on the screen of the MD DISCAM into the address column of Web browsers (Microsoft(R) Internet Explorer, Netscape(R )Navigator, etc.) of the PC just as you do to browse ordinary home pages.
You cannot connect your PC to the Internet having left the TCP/IP settings on the PC in which MD DISCAM connection was made. When you have finished the connection with MD DISCAM, restore the settings for Internet connection. 1. Open APPLE MENU - CONTROL PANEL - TCP/IP. 2. Select "Settings" from FILE MENU. 3. The configuration window as shown on the left appears. Select the name of the configuration for the Internet you usually use ("Internet" in the above case) and click "Make Active".
Note! : Contact a LAN administrator in advance when you connect your MD DISCAM to a LAN installed in a company or a school. In some cases, you cannot automatically obtain an address for the MD DISCAM. In that case, you will have to set the address assigned by the administrator manually. The MD DISCAM has a built-in Ethernet terminal for connection to a PC. Now, let's try to connect the MD DISCAM to the PC on a LAN.
When you connect the MD DISCAM to your PC, you need to make Windows settings. 1. Open "Network" from the Control Panel. 2. The configuration window of "Network" appears. Select the built-in LAN board (the added board or card in the case of additional installation)and open "Properties". 3. The configuration window of "TCP/IP Properties" appears. Check "Specify an IP address" and set the following. IP Address:192.168.0.1 Subnet Mask:255.255.255.0 Now you have set your PC. Let's move on to the MD DISCAM.
After setting your PC, you need to set the MD DISCAM. 1. Select "ADVANCED" - "PC CONNECT" - "SET UP" from the menu of the MD DISCAM. 2. Select " Manual". Touching the white up-and-down arrows with the input pen or using the control dial and set the following. IP Address : 192.168.0.10 Net Mask : 255.255.255.0 Gateway : 0.0.0.0 3. Press "EXEC" and restart the MD DISCAM. 4. When the MD DISCAM restarts, select "ADVANCED" "PC CONNECT" - "CONNECT" from the menu. 5.
When the settings of the PC connection with the MD DISCAM have been completed, the home page address (http://192.168.0.10/) shown on the left appears on the screen. When it appears, let's view pictures and images on your PC. Type the URL shown on the screen of the MD DISCAM into the address column of Web browsers (Microsoft(R) Internet Explorer, Netscape(R)Navigator, etc.), just as you would do to browse ordinary home pages.
Is the browser for your PC set to make access via a proxy server? When access is made through a proxy server, the following "Exceptional Settings" must be added. (When in doubt, contact a network administrator.) 1. Select Control Panel - "Internet Options". 2. Click the "Connections" tab. 3. Click "LAN settings". 4. Click "Advanced" if "Use Proxy Server"* is checked. *If there is no check, access will not go through the proxy server in which case you do not need to create new settings. 5.
The necessary settings of your PC are over. Next, let's make settings for the MD DISCAM. 1. Select "ADVANCED" - "PC CONNECT" - "SET UP" from the menu of the MD DISCAM. 2. Select "Automatic". 3. Select "EXEC" and restart the MD DISCAM. 4. When the MD DISCAM restarts, select "ADVANCED" - "PC CONNECT" - "CONNECT" from the menu. 5. In a little while, the display changes to the window as shown on the left.
When the settings of the PC connection of the MD DISCAM are completed, the home address (http://192.168.0.10/) shown on the left is displayed. *Users with a proxy server setting: Input this address in the column of exceptional settings of the proxy server on your PC.•iWindows•j•iMacOS•j Type the URL shown on the screen of the MD DISCAM into the address column of Web browsers (Microsoft(R) Internet Explorer, Netscape(R)Navigator, etc.), just as you would do to browse ordinary home pages.
Is the browser of your PC set to make access via a proxy server? When access is made through a proxy server, the following "ExceptionalSettings" must be added. (When in doubt, contact a network administrator.) 1. Open the settings (default) of your browser. 2. Select a proxy and set it manually. 3. Input the address of the MD DISCAM in the column that specifies the domain to make direct access.(e.g.192.168.0.
When accessing the MD DISCAM from the PC on a LAN, multiple PC access to the MD DISCAM is not recommended. Concurrent access may sometime cause an extremely delayed response and a hang-up of the system on the MD DISCAM. Please be sure to access from a single PC.
When connecting the MD DISCAM to your PC, start the PC and make settings for the MacOS. 1.First, open APPLE MENU INTERNET ACCESS "Internet Setup Assistant". (Click here when "Internet Setup Assistant" is not installed.) 2. Would you like to set up your computer to use the internet? - Select "Yes". (Refer to the illustration on the left.) 3. Do you already have an Internet account? - Select "Yes". 4. Give a name to this setting. Give a desired name to the setting. It has been named "MD DISCAM" here.
When you connect your MD DISCAM to your PC, power and set up is as follows. 1. Open APPLE MENU - Control Panel - TCP/IP 2. Select "set up" from file menu. 3. Choose one of the settings you already have (we chose "internet" on the left.) and click "Duplicate...". 4. Then the dialogue box will open and you will be able to have it as you like. For example, we named "MD DISCAM" on the left. 5. Click"OK", select "MD DISCAM" and click "Make Active". 6. Chose the way "Ethernet" and will be done "manually". 7.
When your have completed settings of your PC, make settings of your MD DISCAM. 1. Select "ADVANCED" - "PC CONNECT" - "SET UP" from INDEX MENU of the MD DISCAM. 2. Select " Manual". Touching white up-and-down arrows with the input pen or using Control Dial, make settings as follows. IP Address : 192.168.0.10 Net Mask : 255.255.255.0 Gateway : 0.0.0.0 3. Press "EXEC" and restart the MD DISCAM. 4. When the MD DISCAM restarts, select "ADVANCED" "PC CONNECT" - "CONNECT" from the menu. 5.
When the settings of the PC connection of the MD DISCAM have been completed, the home page address (http://192.168.0.10/) shown on the left appears on the screen. When it appears, let's try to capture pictures and images to the PC. Type the URL shown on the screen of the MD DISCAM into the address column of Web browsers (Microsoft(R) Internet Explorer, Netscape(R )Navigator, etc.) of the PC just as you do to browse ordinary home pages.
You cannot connect your PC to the Internet having left the TCP/IP settings on the PC in which MD DISCAM connection was made. When you have finished the connection with MD DISCAM, restore the settings for Internet connection. 1. Open APPLE MENU - CONTROL PANEL - TCP/IP. 2. Select "Settings" from FILE MENU. 3. The configuration window as shown on the left appears. Select the name of the configuration for the Internet you usually use ("Internet" in the above case) and click "Make Active".
