To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (CR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Table of Contents Chapter 1 Introduction Safety precautions. Maintenance .. Chasing a good location . Checking the supplied accessories Hooking up the system Notes on connection Inserting the batteries into the remote commander (only for COPTIC) Identifying the parts Front panel/remote commander Chapter 3 Basic Operations Playing 2 disc .. Playing the entire disc. information display .. Fading in/fading out {only for CPD-312) Locating a particular selection Locating a particular point in 2 selection ..
Unpacking Choosing a Good Location * P Mace the unit in & location with adequate aie circulation to prevent lateral heat build up in the unit, © Do ot place the writ on 3 soft surrogacy, such a5 4 rug that might block the ventilation hols on the button. * Do not install the unit: « near heat sources such ao radiators or Sir ducts, ~ in.
a) for b} ) Hooking Up the System Concept the unit to an amplifier as shown in Fig. BY. &) Compact disc player b} roan AC outlet Q Speakers d) Amplifier Notes on Connection *Turn off the power of each unit before making connections. Connect the AC power cord last. © Be sure to insert the plugs firmly into the jacks. Lose connection may cause hum and noise. * Leave a lithe slack in the connecting cord 1o allow for inadvertent shock or vibration. * The supplied audio cord plugs and jacks ate color coded.
¥ bt RM-D320 {only for CPD-312) Retrofire to the pages indicated i parenthesis for details.
li’] D:E Elmo Dell Playing a Disc In the continuous play mode, you can play from the first selection or desired selection on your disc. Before playing 2 disc, turn on the amplifier and set the input selector to the CD player position. Playing the Entire Disc 41 Press POWER. The display appears. 2 Press & OPEN/CLOSE. Place a disc with the printed side up on the tray. 3 press 11 (w). The disc tray closes and the first selection starts playing. The display shows you the following information.
INT13]40s 10 95,03 WEREN'T =W R 0 formation Display Figure When you press & OPEN/CLOSE to chose the tray, or press TIME in stop made, the display saws you the following information: @) Total number of sections b} Total playing time of the inserted dis Figure [ Each time you press TIME during play, the display changes to gave you the following information.
» e (only for CPD-312) ot et BELLY Playing a Disc Locating a Particular I (Eleazar You can locate the beginning of 2 desired selection in two ways. a) To locate sequentially To locate the beginning of the current or preceding selection * Press I
You can have all the selections played 0 & random order. Shuffle Play 1 Press SHUFFLE. “SHUFFLE” appears 1 the display. 2 Press 18 ). Ta cancel shuttle play Press CONTINUE and the unit enters continuous play mode. “SHUFFLE” gouges off from the display. To check the remaining time Cross TIME once to soe the remaining time of the selection being played, twice to soe the total remaining time, and once more by rectum to the initial display.
1 AMPHORA Playing ina Desired Order You can make a program by designating up to 24 selections in a desired ponder. At the same time, you can adjust the total playing time of the program, 5o that you can make the program fit the length of a tape when recording. Also, if your unit is CPD-312, the total playing time of program selection for side A and B can be adjusted, 5o that you can make two different programs for both sides of the tape when recording. Programming and Recording 1 Press PROGRAM.
{only for COP-312) Plaything Desired Order To play the selections for side B {only for COP-312) When the selections for side & are played, the unit enters pause mode. Reverse the apu, then press E>BE (9 or 16), To stop playing Press . When you press E88 you can play the same program repeatedly. To cancel program play Press CONTINUE or SHUFFLE and the unit enters continuous or shuttle play mode respectively. The program will be erased. To check your program Press CHECK.
CHECK CLEAR = CHECK {only for COP-312) BV R F Desired Order Changing Your Pro You can make the following changes before starting play. To erase the last selection, press. CLEAR, Each time you press CLEAR, the last selection in the program will be erased, Yo areas the entire program, press M once in slop mode; twice during play. The program is also erased when you tum off the unit or you press & OPEN/CLOSE.
REPEAT 1 $ Decennial Playing Repeatedly You can choose between twa different repeat play modes. One repeats ol the selections ins the current play made, the other repeats any given selection. Repeat Play To repeat all selections a} Press REPEAT acne. REPEAT” appears in the display. The unit will repeat in the current play made.
2-b) Designating the . Total Playing Time K1 You can designate a playing time and the unit will make 2 different programs of selections each fitting within that period. These programs can contain up to a total of 24 selections. Use this function, by designating the length of your tape, for editing both sides of a tape. This function, called time edit, sets the playing time of each program within the designated time automatically, by choosing selections in numerical order which changes as little as possible.
Designating the Total LR A 4 press MEDITATIVE FADE once more while *B” in the tape Indicator Is Hashing. Another program for the either side completed. 5 press 11 The selections for side A will be played and then the unit will pause. Reverse the tape, then press Beanbag (9w again o ). The selections for side 8 will be played To cancel the edit Press CONTINUE or SHUFFLE and the unit enters continuous of shuffle play mode respectively. The programs will be erased. Yo check the program See page 12.
EQUITY TIME FADE z-a) b) Fading Out at the Desired Time Time Fade f You can end the play fading out by designating the play duration. Once the time fade is set, it functions twice for editing both sides of a tape. You can change discs without canceling this function and use it in any play mode. 1 Press EDIT TIME FADE twice in stop mode {or press it once in pause demode. “TIME FADE" and “A” in the tape indicator displayed in the display. 2 Set the desired play duration.
Specifications Compact disc player Laser Semiconductor laser Wavelength 780 -~ 790 nm Frequency response 2 Hz toot kHz £05dB Signal-to-noise ratio More than 97 dB Dynamic range More than 95 dB Harmonic distortion Less than 0.0050 % Channel separation More than 9348 Outputs LINE QUT {phonon jacks) Output level kilo hums) Load impedance over 10 kilograms General Power requirements. VACANT O Hz Power consumption 1w Dimensions {approx., including projections) 430 x 100 295 mm (17 x4x 1%/, inches) Mass {approx.
Troubleshooting Guide Before going through the check list below, first refer back to the connections and carpeting procedures. Should any problem persist after you have made these checks, consult your nearest Sony service facility. Symptom Cause Remedy The disc tray does not close. ‘The disc is not placed correctly. Place the disc correctly on the disc tray., Play does not start. Dirty disc. Clean the disc. The disc is inserted upside down. inert the disc with the printed side up. A pause is engaged.
