CD-R/RW SCSI Drive Unit CD-R/RW SCSI Drive Unit User’s Guide Mode d’emploi Bedienungsanleitung Manual de instrucciones Manuale d’istruzione ©1999 by Sony Corporation Rev. 1.
The model and serial numbers are located on the top of the drive. Record these numbers in the spaces provided below. Refer to them whenever you call upon your sales representative regarding this product. Model No. __________________ Serial No. ___________________ Safety Regulations This unit uses CD-R discs and CD-RW discs with the following mark. English Owner’s Record This unit uses CD-ROM discs with the following mark.
Contents Introduction Introduction 5 Features..........................................................................................................5 System Requirements for WINDOWS 95/98/NT ............................................5 Location and Function of Parts and Controls 6 Front Panel / Rear Panel ................................................................................6 Precautions 7 Hardware Installation 7 Installing the Drive Unit into the Computer............................
Location and Function of Parts and Controls Precautions Front Panel ■ Installation Avoid placing the drive in a location subject to: – high humidity – high temperature – excessive dust – mechanical vibration – direct sunlight. Only horizontal drive operation recommended, not vertical or tilted. ● ■ Operation ● ● Headphone Jack Headphone Volume Control Busy Indicator Disc Drawer Emergency Eject Eject Hole Button Do not move drive during operation, it may cause an error.
Step 1: Opening the Computer Step 3: Finding the Connector First turn off computer and remove / unplug all power cables! Remove computer cover as directed in the User’s Manual. The SCSI cable should have 1 or more unused connectors on the end opposite the adapter, as shown, find a connector not in use. We recommend a connector at the very end of the 50 pin SCSI cable. Step 2: SCSI Configuration Locate the 50 pin SCSI cable in your computer.
The following table shows the function of each jumper. Step 5: Setting the Jumpers Set jumpers on rear of drive unit according to your computer configuration. Jumpers are factory preset as shown below. Jumper ACTIVE TERM TEST ACTIVE TERM ID SELECT TEST ID 1 ID 2 ID 4 ACTIVE TERM TEST ID 1 ID 2 ID 4 Function ON: Enables active termination OFF: Disables active termination ON: OFF: Enables test mode Enables normal operation Assign the drive unit’s ID number by setting these jumpers to ON or OFF.
Step 6: Connecting the Drive Step 7: Mounting the Drive Attach flat SCSI cable to connector at rear of CD-RW drive. CD-R/W Drive Unit Audio Out Connector Interface Connector Insert the CD-RW drive into computer front as shown, routing cables accordingly. Secure drive to frame with appropriate screws. Pin 1 Power Supply Connector Red Edge Mounting Screws SCSI Flat Cable Flat Cable Audio Cable Audio Cable Note: Slide rails (not included) may be necessary if you cannot secure CD-RW drive.
Software Installation Step 9: Installation Review Now let us review the hardware installation process, assuring that: ● All connectors are properly connected. ● Each SCSI device has its own unique SCSI ID number. ● The last physical SCSI device on the bus is properly terminated. Please refer to CD-RW formatting software/CD manual for instruction on software installation. CD-RW formatting software must first be properly installed in order to write CD’s with this device.
Operating the Drive Assure application software is installed before using the CD-RW drive. Starting Up 1 Turn on the computer. 2 Press eject button and the tray extends from drive unit. As the drive begins reading the Table of Contents (TOC) data, the busy indicator lights and remains illuminated until read is completed. When the busy indicator switches off, the drive is ready to receive commands, data may be retrieved from the disc.
Troubleshooting Should problems occur while installing or operating the drive: ● ● Please verify the steps of this manual were carefully followed. If problem still exists, please confirm the items in ”Checklist“ below. Technical Support If you require further support or service please contact your local Sony technical support professionals. For Europe (German or English) contact the hotline at: Tel.: +49 (0) 2389 - 951047 or SONY-HOTLINE@SUPLIE.
Specifications ■ General Host interface SCSI-2, single ended, 50 pin Line out: Headphone: 0.7 V at 47 kΩ 0.55 V at 32 Ω ■ Audio ■ Environmental conditions Relative humidity Climate gradient Temperatures Operating Transport (72 hours max.) Storage (6 month max.) 10% to 90% (no condensation) 10°C/hour, 10% humidity/hour 5°C to 45°C (41°F to 113°F) –40°C to 60°C (–40°F to 140°F) –30°C to 50°C (–22°F to 122°F) Design and specifications subject to change without notice.
DC INPUT ACTIVE TERM TEST ID SELECT 012 AUDIO OUT R GND L Important: Le dépassement des vis ne doit pas excéder 6,0 mm par rapport à la surface des panneaux latéraux et de la plaque inférieure. 42.3 21.9( ) 10 (13/32) 7/8 0.4 (1/32) 47.5 (17/8) 79.25 (31/8) + + 139.
