PCG-C1VP/C1VPK SERVICE MANUAL US Model Canadian Model S400 l a i t n e d i f n o C Notebook Computer 9-872-222-11
Information in this document is subject to change without notice. Sony and VAIO are trademarks of Sony. Microsoft, MS-DOS, Windows, the Windows 95, Windows 98, Windows 2000 and Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack of equipment or in both the operating and the service instructions. CAUTION: Danger of explosion if battery is incorrectly replaced.
TABLE OF CONTENTS Section Title Page CHAPTER 1. REMOVAL 1-1. 1-2. 1-3. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Flowchart ......................................................................... 1-1 Main Electrical Parts Location Diagram ......................... 1-1 Removal ........................................................................... 1-2 Key Board Unit ................................................................ 1-2 Cursor Sensor Module ...........................
CHAPTER 1. REMOVAL 1-1.
1-3. Removal 1. Key Board Unit 3 Open in the direction of arrow. Key Board Unit 4 Harness 2 Claw 1 M2X8 2 Claw 2.
3. Palm Rest Sub Assy 1 Heatsink (Card Slot) 4 M2X6 5 M2X6 8 FFC (MBX-SWX63) 7 FFC (MBX45-SWX62) 5 M2X6 Palm Rest Sub Assy 9 Claw 2 Undo three claws and remove the main cover (L). 3 Undo three claws and remove the main cover (R). 6 M2X8 6 M2X8 4.
5. SWX-63 Board SWX-63 Board 3 FFC (MBX-SWX2) 2 Harness 1 M2X4 2 Harness 6.
7. IFX-128 Board 1 Harness IFX-128 Board 8.
. Assy HDD 15 GB T 1 FFC (MBX-45-CNX108) 2 M2X5 2 M2X5 Assy HDD 15 GB T 3 Print PWB Simple Substance 10.
11. Fan With Heatsink Thermal Sheet (T) Fan With Heatsink * The fan with heatsink must be installed with the thermal sheet (T) in soft state to protect the CPU from the stress. For this purpose, with the thermal sheet (T) pasted, warm the fan with heatsink to about 70 °C, and when the thermal sheet (T) has become soft, install the fan with heatsink on the main board. 1 Harness 2 M2X4 12.
13. LCD Housing Assy LCD Housing Assy 1 LCD Harness 2 M2X5 3 M2X3 Grip 14.
15. Bezel Assy 8 Undo ten claws and remove the bezel assy. 7 M2X5 6 Blind Rubber (Left) 1 Undo three claws and remove the hinge cover assy. 3 M2X6 5 M2X5 2 Blind Rubber (Lower) 4 Blind Rubber (Right) 2 Blind Rubber (Lower) 1 Undo three claws and remove the hinge cover assy. 3 M2X6 16.
17. CCD SD22 Assy, Inverter Unit 6 Microphone Assy, CCD SD22A Assy 3 LCD Harness 5 Lock Ace (M2.6) 4 M2X4 1 Flexible Print PWB 2 Inverter Unit qa Microphone Holder qf Bearing (C) 0 Lock Ace (M2.6) 9 Microphone Cover Assy CCD SD22 Assy * Do not dismantle the CCD SD22 Assy. For example, removing the connector. 8 M2X3 7 Blind Plate (Microphone) qd Tapping Screw (1.7X3) qs Ring (F) * When mounting the ring (F), Align markings of camera (side of gear) and groove of ring (F).
CHAPTER 2. SELF DIAGNOSTICS < ATTENTION > Please confirm “Self Diagnostics” method which will be informed you with distribution of “Self Diagnostics” software.
CHAPTER 3. BLOCK DIAGRAM BusMaster --------REQ0/GNT0 REQ1/GNT1 REQ2/GNT2 REQ3/GNT3 REQ4/GNT4 REQ5/GNT5 MIC CAM / BCX-SD22A 1A 1/6" 760H + INT/PG CONV PCLK ----PCLK0 AD19 PCLK1 AD20 PCLK5 AD23 PCLK6 AD16 PCLK4 AD21 PCLK2 AD22 PCLKF AD18 PCLK0/3 IDSEL ----PIRQD PIRQC PIRQB PIRQA PIRQB PIRQB INTA ----i.LINK (Sony) Audio (YAMAHA) CardBus (Richo) Video (ATI) Modem M-Chip (Kawatetsu) PIIX4E (Intel) TM5600 (TRANSMETA) S DRAM VCC 3.3V (+3VSUS) HCLK0 Graphics MJPEG ATI Mobility-M1 8MB SGRAM +3VSUS +2.
CHAPTER 4.
CHAPTER 5. EXPLODED VIEWS AND PARTS LIST Ref.No. Part No. 1 A-8066-764-A 2 1-794-957-11 3 4-643-063-01 4 4-648-579-01 *5 4-648-584-02 NOTE: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “ * ” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
5-2. LCD Section Ref.No. Part No.
5-3. Accessories Ref.No. Part No. ACCESSORIES *********** 202 Display Adaptor (1) Description 202 0203 204 0206 207 1-757-026-11 1-418-518-32 1-756-074-21 1-757-562-31 4-643-958-01 CABLE, VGA ADAPTOR, A.C. BATTERY PACK, LITHIUM ION CORD, POWER CAP (IN BAG), SENSOR 209 1-765-080-31 CORD, CONNECTION 4-655-539-11 QUICK START, C1 203 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
PCG-C1VP/C1VPK (UC) PCG-C1VP/C1VPK (UC) 9-872-222-11 2001F0500-1 This manual and the constituent data may not be replicated, copied nor reprinted in whole or in part without prior written authorization of Sony Corporation. Sony Corporation 9-872-222-11 – 30 – English 2001F0500-1 © 2001 Sony Corporation Published by MNC IT Planning & Control Dept.
