Operating Instructions - Operating Instructions

Specifications
85
GAMUT3
5)
, S-GAMUT3.Cine,
ITU-R BT.2020
Warm-up time Approx. 30 minutes
To provide stable picture quality, turn
on the power of the monitor and
leave it in this state for more than 30
minutes.
1) 48 Hz and 60 Hz are compatible with a frame rate of 1/
1.001.
2) DCI: x=0.314 y=0.351
3) Chromaticity points of SMPTE RP 431-2, ITU-R BT.2020,
S-Gamut/S-Gamut3, and S-Gamut3.Cine are not covered
in full.
4) The BVM-E171 individual chromaticity points. The widest
color space setting of the signal reproduced by the BVM-
E171
(Typical)
5) For displaying the color space of the wide color space mode
which is available for the F65 or PMW-F55/F5 CineAlta 4K
Camera, etc.
Input
SDI BNC (×2)
Input impedance: 75 ohms unbalanced
Signal format: See “Available Signal
Formats” (page 86).
Sampling frequency
3G-SDI:
Y/Cb/Cr (4:2:2): 148.5 MHz/74.25
MHz/74.25 MHz
Y/Cb/Cr (4:4:4): 74.25 MHz/74.25
MHz/74.25 MHz
G/B/R (4:4:4): 74.25 MHz/74.25
MHz/74.25 MHz
HD-SDI:
Y/Cb/Cr (4:2:2): 74.25 MHz/37.125
MHz/37.125 MHz
SD-SDI:
Y/Cb/Cr (4:2:2): 13.5 MHz/6.75
MHz/6.75 MHz
Quantization
3G-SDI: 10bit/sample, 12bit/sample
HD-SDI: 10bit/sample
SD-SDI: 10bit/sample
Composite input (NTSC/PAL/PAL-M)
BNC type (×1)
1 Vp-p ±3 dB sync negative
HDMI HDMI (×1)
HDCP1.4 correspondence, Deep Color
correspondence
Signal format: See “HDMI” (page 90)
of “Available Signal Formats”.
Parallel remote RJ-45 (×1)
Serial remote (LAN)
Ethernet (10BASE-T/100BASE-TX)
RJ-45 (×1)
Output
SDI BNC (×2) (monitor output)
Output signal amplitude: 800 mVp-
p±10%
Output impedance: 75 ohms
unbalanced
Transmission distance:
3G-SDI: 70 m max.
1)
HD-SDI: 100 m max.
1)
SD-SDI: 200 m max.
2)
Composite output
BNC type (×1)
Loop-through
3)
, with 75 ohms
automatic terminal function
DC 12V OUT Circle 4-pin (female) (×1)
1) When using the 5C-FB coaxial cable made by Fujikura Ltd.
or equivalent
2) When using the 5C-2V coaxial cable made by Fujikura Ltd.
or equivalent
3) When the unit is turned off, the signal wave may be
distorted.
General
Power requirements
100 V to 240 V AC, 0.9 A to 0.5 A, 50/
60 Hz
24 V to 28 V DC, 3.3 A to 2.9 A
Power consumption
Approx. 88 W (when AC power source
is used) / Approx. 78 W (when DC
power source is used) (max.)
Approx. 53 W (when AC power source
is used) / Approx. 49 W (when DC
power source is used) (average
power consumption in the default
status)
0.3 W (In off-mode (When the power
switch is off))
Operating temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended: 20 °C to 30 °C (68 °F to
86 °F)
Operating humidity
30% to 85% (no condensation)
Storage/transport temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Storage/transport humidity
0% to 90%
Operating/storage/transport pressure
700 hPa to 1060 hPa
Mass Approx. 6.5 kg (14 lb 5.3 oz)
Accessories supplied
AC power cord (1)
xy
R 0.681 0.319
G 0.189 0.724
B 0.141 0.051