Specifications

28
Location and Function of Parts
5.4 IP Control Cards
The following provides information on the location and function of IP control card parts.
5.3.15 BRBK-SF1 HD Optical
Multiplex Card
AUDIO IN BRU
BRBK-SF1
LR
1 2
1
AUDIO IN L/R jacks (phono type)
Input an audio signal (stereo), which is output
from the AUDIO OUT jacks on the BRU-SF10 HD
Optical Multiplex Unit via the Optical Fiber
Cable.
Note
The audio input on this card accepts audio line
signals only. When you input audio signals from a
microphone, etc., it should be connected with a
microphone amplifier so that audio signals with
an appropriate audio level can be input.
2
Optical connector
5.4.1 BRBK-IP10 for use with the
BRC-H900 and BRC-Z330
SDI OUTLAN
BRBK-IP10
ON
HD SD
OFF
DATA MIX
21
1 2 3 4
1
LAN connector (RJ-45 8-pin)
Connect to a switching HUB that is compatible
with 10BASE-T/100BASE-TX using a LAN cable
(category 5 or higher, straight).
When a link is established, the green indicator
lights, and it flashes during communication.
While connected with 100BASE-TX, the yellow
indicator also lights.
Note
When the IP control card BRBK-IP10 is inserted into
the camera, the RS-232C and RS-422 connectors
cannot be used.
2
Reset switch
If you press down this switch with a pointed tip
for about five seconds, the camera will reboot
and the IP control card BRBK-IP10 will return to
the factory setting.
Factory settings for BRBK-IP10
•IPaddress:192.168.0.100
•Subnetmask:255.255.255.0
•Name:CAM1
3
SDI 1, 2 connector (BNC type)
Outputs down-converted SD-SDI signals that
conform to SMPTE 259M serial digital interface
standards, or HD-SDI signals that conform to
SMPTE 292 serial digital interface standards.
When the menu display for the camera is
turned ON, you can use the
4
HD/SD select
switch to output the menu display signal that
overlaps the images, from this connector.
4
HD/SD select switch
Switches between SD-SDI signals and HD-SDI
signals.
When outputting HD-SDI signals, you can select
whether to overlap the menu display with the
image output from SDI connectors 1 and 2.
•“HD/DATAMIX:ON”OutputsHD-SDIsignaland
the menu display is overlapped.
•“HD/DATAMIX:OFF”OutputsHD-SDIsignaland
the menu display is not overlapped.
•“SD”:OutputsSD-SDIsignalandthemenu
display is overlapped.
Note
•SD-SDIandHD-SDIsignalscannotbesupplied
simultaneously.
 •SettheHD/SDselectswitchbeforeturningon
the camera.
 •Donotpushtheswitchforciblywithascrew-
driver, etc.
5.4.2 BRBK-IP7Z for use with the
BRC-Z700
SDI OUTLAN
BRBK-IP7Z
HD SD
21
1 2 3 4
1
LAN connector (RJ-45 8-pin)
Connect to a switching HUB that is compatible
with 10BASE-T/100BASE-TX using a LAN cable
(category 5 or higher, straight).
When a link is established, the green indicator
lights, and it flashes during communication.
While connected with 100BASE-TX, the yellow
indicator also lights.
Note
When the IP control card BRBK-IP7Z is inserted into
the camera, the RS-232C and RS-422 connectors
cannot be used.