DSLR-A200 SERVICE MANUAL LEVEL 2 AEP Model UK Model Chinese Model Japanese Model Ver. 1.0 2007.12 Revision History Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité.
SPECIFICATIONS Camera [Exposure] [System] Metering Cell 40-segment honeycombpattern SPC Camera Type Digital Single Lens Reflex Camera with built-in flash and interchangeable lenses Lens All of α Lens [Image sensor] Total pixel number of camera Approx. 10 800 000 pixels Effective pixel number of camera Approx. 10 200 000 pixels Image format 23.6 × 15.
1. SERVICE NOTE ENGLISH JAPANESE 1-1. CHEMICALS Some chemicals used for servicing are highly volatile. Their evaporation caused by improper management affects your health and environment, and wastes resources. Manage the chemicals carefully as follows. • • • • Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight. Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
ENGLISH JAPANESE 1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUS PLATE 1 Remove two claws pushing part A below, and remove VM FS retainer in the direction of arrow. 3 Remove focus plate and VB spacer. VB Spacer Claw A Claw Focus Plate VM FS Retainer 2 Remove VM FS retainer. VM FS Retainer 4 Remove SI screen. SI Screen Claw Note: When you exchange the SI screen, don't put dust or give a scratch.
1. SERVICE NOTE ENGLISH JAPANESE 1-1. 各種薬品の取り扱いについて 現在使用されている薬品の中には揮発性の高い薬品もあります。 それらを不用意に取り扱い蒸発させてしまうと，環境や健康へ影響を与えたり，資源の無駄使いになります。 各種薬品は，下記の点に注意して取り扱ってください。 ・ ・ ・ ・ 保管場所を定め，高温になったり直射日光の当たらない場所に密閉して保管してください。 小分け（ハンドラップ等）する数は必要最小限に留め，容器による自然蒸発を防いでください。 作業に使用しない時は，必ずキャップ等をして自然蒸発を防いでください。 薬品を使用する回数を極力少なくし，使用する場合は使用する量だけ容器より出して受け皿に残さないようにしてくだ さい。 1-2.
ENGLISH JAPANESE 1-4. SAFETY CHECK-OUT サービス，点検時には次のことにご注意ください。 1. 注意事項をお守りください。 サービスのとき特に注意を要する個所については，キャビネット，シャーシ，部品などにラベルや捺印で注意事項を表 示しています。これらの注意書き及び取扱説明書等の注意事項を必ずお守りください。 2. 指定部品のご使用を セットの部品は難燃性や耐電圧など安全上の特性を持ったものとなっています。 従って交換部品は，使用されていたものと同じ特性の部品を使用してください。 特に回路図，部品表に0印で指定されている安全上重要な部品は必ず指定のものをご使用ください。 3. 部品の取付けや配線の引きまわしはもとどおりに 安全上，チューブやテープなどの絶縁材料を使用したり，プリント基板から浮かして取付けた部品があります。 また内部配線は引きまわしやクランパによって発熱部品や高圧部品に接近しないよう配慮されていますので，これらは 必ずもとどおりにしてください。 4.
ENGLISH JAPANESE 1-5.
2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. • When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) • When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped.
2-1. IDENTIFYING PARTS - DISASSEMBLY FLOW - Rear Cover ⋅ LF-056 Flexible Board 2-2-1. OVERALL SECTION ⋅ Side Cover ⋅ Rear Cover ⋅ Front Cover 2-2-2. FRONT COVER SECTION ⋅ Control Switch Block (FS62700) ⋅ Grip Cover 2-2-4. MAIN BOARD SECTION ⋅ AM-013 Board ⋅ MM-076 Board 2-2-3. REAR COVER SECTION ⋅ Control Switch Block (RS62700) ⋅ LCD AM-013 Board ⋅ MM-078 Flexible Board Top Cover 2-2-5.
HELP 2-2. DISASSEMBLY EXPLODED VIEW HARDWARE LIST 2-2-1. OVERALL SECTION Follow the disassembly in the numerical order given. 1 Side Cover (1-1 to 1-3) 2 Rear Cover (2-1 to 2-10) 3 Front Cover (3-1 to 3-6) Note: High-voltage cautions Discharging the Capacitor Short-circuit between two points with the short jig about 10 seconds.
2-2-2. FRONT COVER SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-3. REAR COVER SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-4. MAIN BOARD SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-5. SHUTTER UNIT SECTION EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Tebure Unit (1-1 to 1-12) 2 Shutter Unit (2-1) 1 Tebure Unit Do not hang flexible board of mirror box when yuo remove Tebure Unit. Refer to page 2-16 "2-3. IMAGER INCLINATION ADJUSTMENT" when the tebure unit is installed.
2-2-6. BOTTOM FRAME SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-7. TOP COVER SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-8. FLASH UNIT SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-9. BATTERY HOLDER SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-10. TERMINAL HOLDER SECTION EXPLODED VIEW Follow the disassembly in the numerical order given.
2-2-11. MIRROR BOX SECTION (PENTA UNIT) EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Penta Unit (1-1 to 1-2) 1 Penta Unit Refer to page 1-2 "1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUS PLATE" when SI screen or focus plate are exchanged.
2-2-12. MIRROR BOX SECTION (SUB UNIT-1) EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Iris Ring (1-1 to 1-9) 2 Aperture Unit (2-1 to 2-5) 3 AF Driving Unit (3-1 to 3-9) 2 Aperture Unit Refer to page 2-18 "2-6. APERTURE UNIT INSTALLATION" when the aperture unit is exchanged. Mirror Box Section (Sub Unit-2) 2-1 (See Page 2-15) HELP 22 2-5 2-4 (#12) 1 Iris Ring Refer to page 2-18 "2-5. IRIS RING REMOVAL/INSTALLATION" when the iris ring is exchanged.
2-2-13. MIRROR BOX SECTION (SUB UNIT-2) EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Charge Base Plate A Unit (1-1 to 1-11) 2 Shutter Charge Lever (2-1 to 2-12) 2-12 Refer to page 2-20 "2-9. LEVERS AND GEARS INSTALLATION" when you exchange parts around the mirror charge lever.
2-3. IMAGER INCLINATION ADJUSTMENT Checking Method 1. Use the copy stand or place a mirror on the wall, and adjust the accuracy so that the camera is opposed to the mirror. 2. Use the AE master lens as an inspection lens. 3. Obtain the inclination angle with the Photoshop, and perform as follows according to the angle: • For the angle above ± 1.0 degree, be sure to repair the camera. • For the angle above ± 0.5 degree and below ±1.0 degree, repair the camera according to the user's requirement level.
2-4. SHUTTER INSTALLATION Follow the assembly in the numerical order given. 1 Raise Main Mirror up. Mirror Charge Lever Up 2 Rotate Idle Gear Don't damage Idle Gear.
2-5. IRIS RING REMOVAL/INSTALLATION Removal Rotate the iris ring clockwise, and remove it at the stop position (iris-in end). At this time, do not rotate the iris joint gear of the Aperture Unit. Installation 1. With the Aperture Unit set in the charge position (see "2-7. Aperture Unit Charge Position Setting" ), install it on the front frame set. * The Aperture Unit has been set in the charge position, if it is not removed.
2-8. APERTURE UNIT FREE POSITION SETTING 1. Set the Aperture Unit to a free position once, if the gear was rotated accidentally and the charge position is disordered, or if the charge position was shifted during disassembly. In a free state, the edge of this spring will move up and down about 1 mm if the gear is moved a little. Gear rotating direction to set the charge position In a free state, a hole in the gear almost coincides with a hole in the Aperture Unit.
2-9. LEVER AND GEARS INSTALLATION Follow the assembly in the numerical order given. 2-9-1. MIRROR CHARGE/SHUTTER CHARGE LEVERS INSTALLATION 1 Mirror Charge Lever Assy - Levers Position Mirror Charge Lever Assy 4 Screw (#93) 3 Charge Base Plate C Assy Main Mirror Holder Boss 2 Shutter Charge Lever Spring Shutter Charge Lever 2-9-2.
2-9-3. CHARGE BASE PLATE B INSTALLATION 1 Charge Base Plate B Assy 2 Screw (#93) Hole Hole 2-9-4.
2-10.GREASE APPLICATION AREA Grease uses G-85 (J-6082-626-A).
2-11.CLEANING PROCEDURE OF OLPF Make it to Cleaning Mode of Power On/Set Up Menu by using the AC power supply. (It comes to Mirror Up/Shutter Open) Note: Use the AC power supply absolutely. 1. Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A). Cut Cleaning Cloth (J-6082-636-A) EE3310 Cleaning Jig (J-6082-635-A) 2. Surface of OLPF is cleaned. (Note that there is no wipe irregularity) 3.
HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 5: Switch Block Control Unit (RS62700) HELP 8: IS Flexible Unit Switch Block Control Unit (RS62700) Fold Fold Adhesive Tape Claw IS Flexible Unit LCD Flexible Board LF-056 Flexible Board HELP 6: Charge Base Plate A Unit Harness HELP 9: Shutter Unit Boss Charge Base Plate B Assy Claw Shutter Unit Charge Base Plate A Unit Harness HELP 7: PC Board Electrostatic Sheet HELP 10: Flush Unit Harness/Tape (W) Pink Between Land Gray White Red Yellow PC Board Electrostatic Sheet Tape (W) DSLR-A2
HELP 11: DC Jack Harness Rib Rib Rib Rib HELP 12: Flash Unit Harness/Tape (W) Rib Rib Rib Flash Unit Harness Tape (W) Tape (W) DSLR-A200_L2 HELP
HELP 13: Flush Unit HELP 16: GY-008 Flexible Board GY-008 Flexible Board Boss HELP 14: CV Self LED Electrostatic S CV Self LED Electrostatic S HELP 17: MA-450 Flexible Board MA-450 Flexible Board GY-008 Flexible Board HELP 15: CT Mode Dial Assy HELP 18: RM-096 Flexible Board Rib CT Mode Dial Assy Rib Boss RM-096 Flexible Board DSLR-A200_L2 HELP
HELP 19: DC Jack Harness HELP 22: Aperture Unit Flexible Borad Iris FPC Protection Sheet Aperture Unit Flexible Borad AF Driving Unit Iris FPC Protection Sheet Flexible Borad Rib HELP 23: Coupler Lever Tension SP Coupler Lever Tension SP HELP 20: BD Side Cover (L) Sheet BD Side Cover (L) Sheet Coupler Joint Lever HELP 24: Shutter Charge Lever SP Shutter Charge Lever HELP 21: AF Module Flexible Board Shutter Charge Lever SP HELP 25: CV Rear Flex Insulating Sheet CV Rear Flex Insulating Sheet 1 mm
3.
3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-2. OVERALL BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-3. OVERALL BLOCK DIAGRAM (3/5) AF-111 FLEXIBLE BOARD 14 IC7801 AF CCD ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-4. OVERALL BLOCK DIAGRAM (4/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-5. OVERALL BLOCK DIAGRAM (5/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (5/5) CN3517 (2/2) XS2 12 4 XIMG_RESET XIMG_RESET_O OVERALL (1/5) (PAGE 3-1) K4 R16 P13 T12 U12 D1 E2 A2 M17 OVERALL (4/5) (PAGE 3-4) XCS_VG XCS_HPY2 XWAKE_BY_VG BATT_1_ON BATT_1_SEL BATT_2_ON BATT_2_SEL VGDET IC3713 D3003 3.7V DETECT (13/19) CA_UNREG 5 1 XCA_RESET EVER_3.
3-6. POWER BLOCK DIAGRAM (1/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (1/5) + 1 S 2 – 3 CN0503 BATT_UNREG Q0502, Q0503, Q0505 B+ SWITCH F0501 A D0505 F0502 POWER (3/5) (PAGE 3-8) Voltage selection of IC_3001_3.3V_POWER_ON H IC_3001_3.3V/5.0V 5.0V D0506 CN0501 ACV_UNREG 1 BATT/XEXT 2 3 C POWER (2/5) (PAGE 3-7) BATT_IB BATT_SIG XDC_JACK_SENSE J902 DC IN UNREG_LVDD0 UNREG_FLASH F0503 L 3.
3-7. POWER BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (2/5) IC_3001_6.0V IC_3001_6.0V IC_3001_6.0V IC_3001_3.3V IC_3001_3.3V IC_3001_3.3V CN3526 BZ_VDD E POWER (1/5) (PAGE 3-6) CN3524 BL_A UNREG UNREG EVER_3.3V EVER_3.
3-8. POWER BLOCK DIAGRAM (3/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (3/5) G POWER (1/5) (PAGE 3-6) IC_3001_2.5V VREF_CAM EVER_1.5V EVER_3.3V IC_3001_2.5V VREF_CAM EVER_1.5V EVER_3.3V IC3001 IC3713 M IC3003 3.7V DETECT (13/19) CA_UNREG MAIN CPU (6/19) 16K EEPROM (6/19) 5 VDD VOUT 1 POWER (2/5) (PAGE 3-7) XCA_RESET XCA_RESET P17 RESET CA_UNREG EVER_3.
3-9. POWER BLOCK DIAGRAM (4/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (4/5) AF-111 FLEXIBLE BOARD IC_3001_3.3V AS_5.0V EVER_3.3V CN3511 VCC1 5 VDD 6 IC_3001_3.3V (AFCCD_3.3V) AS_5.0V EVER_3.3V S EVER_3.3V EVER_3.3V IC_3001_3.3V IC7801 AF CCD AFCCD_RST RST POWER (3/5) (PAGE 3-8) 8 9 RST IC3801 AS_7.
3-10. POWER BLOCK DIAGRAM (5/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-013 BOARD (5/5) IC2801 VIDEO AMP (18/19) IMG_3.3V EVER_3.3V I FVDDEN H4 FRESET J1 L2301 POWER (1/5) (PAGE 3-6) MM-078 FLEXIBLE BOARD D2501 (ACCESS) CN2501 CF_3.3V Q2504 B+ SWITCH MEDIA_3.3V IMG_1.2V CPC (For Check) IC2501 CF DETECT (17/19) MEDIA_3.3V 1 CF_3.3V_PWR_ON XCF_RST XCF_RST MM-076 BOARD 33, 34 EVER_3.3V CN2806 3.3V IMG_3.
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1.
4-2.
4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS (ENGLISH) THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip.
4-2.
1 3 2 4 7 6 5 8 10 9 11 12 15.1 R4317 220k 1/16W ± 5% IDRV OUT 3 Vcc GND 2 ISF IN A CCDOUT_RB-BUFF VOUT_RB 1 Note: IC4303 (CCD imager), IS-026 complete board and all mounted parts are not supplied, but they are included in CCD assy 627. 4 C4311 0.1u C C4320 0.001u B C4322 0.1u C 5 A IC4304 CXA3691EN-T9 BUFFER 6 R4315 100k 1/16W ± 5% 3 6 5 2 4 FB4331 15.1 IC4302 TK71828CBCB-G 2.8V REG IDRV OUT 3 Vcc GND 2 L4302 10uH 3.
1 3 2 4 7 6 5 8 10 9 11 12 A A FB4201 DRVDD_RB 9 H2 6 GNDH1 5 LH GNDH2 GNDH1 H1 VDDH2 RG VDDH1 GNDL GNDH2 GNDL R4235 2.2 7 8 GNDL GNDL GNDL GNDL NC VDDL IC4204 CXA3759ER-T2 H-DRIVER 4 C4204 0.1u B VDDH1 GNDL 3 C4205 4.7u 6.3V GNDL VDDH2 2 V4F_C GNDL GNDL 1 1u HVDD_RB C4202 V3F_B FB4203 L4203 10uH V3F_F A1 A2 B V4F_F B 27 26 25 24 23 22 21 20 19 C4224 0.1u B V3F_C EN1 18 17 16 15 14 13 12 11 10 H2F_RB R4232 2.
1 3 2 4 7 6 5 8 10 9 11 12 A A FB4101 DRVDD_G 9 GNDL GNDH2 H-DRIVER VDDH2 8 H2 6 LH GNDH1 GNDH1 4 IC4104 CXA3759ER-T2 5 VDDH1 GNDL H1 RG GNDH2 VDDH1 GNDL GNDL R4135 2.2 7 GNDL GNDL GNDL A1 NC GNDL GNDL 3 C4104 0.1u B VDDH2 2 1u C4105 4.7u 6.3V C4102 V2F_E GNDL 1 HVDD_G V1F_F FB4103 L4103 10uH V1F_B VDDL A2 B V2F_A B 27 26 25 24 23 22 21 20 19 C4124 0.1u B V1F_E EN1 18 17 16 15 14 13 12 11 10 H2F_G R4132 2.
Schematic diagrams of the AM-013 board is not shown. Pages from 4-7 to 4-25 are not shown.
1 2 3 4 5 7 6 8 10 9 11 A A B CN9401 1 GRB SDA HSYNC LN9415 DCLK LN9413 D6 LN9411 D4 LN9409 D2 LN9407 D0 NC LN9405 NC LN9403 D pin2 LN9402 pin1 LN9401 VDD PNLSEL DGND VLED+ NC NC VLED- LN9404 D0 NC VLED+ LN9406 D2 D1 D1 LN9408 D4 D3 D3 LN9410 D6 D5 D5 LN9412 CN3529 Page 4-25 of Level 3 DCLK D7 D7 LN9414 AM-013 (19/19) VSYNC VSYNC LN9416 HSYNC VLEDVDD R9401 PNLSEL R9402 B 45P VCOM NC(AUO)GND(SONY) 3 GRB 4 CS 5 SDA 6 SCL 7 HSYNC 8
1 3 2 4 5 7 6 8 10 9 11 12 A A C5201 XX R5201 XX C5205 1u B CN5202 CF_3.3V CN5201 B 51P REG_GND 1 CF_D06 2 REG_GND 3 CF_D04 4 CF_D10 6 CF_D14 7 CF_D00 8 CF_D11 9 CF_D09 XCF_OE C MM-078 FLEXIBLE LN6752-LN6802 Page 4-38 of Level 2 14 D REG_GND 18 REG_GND 19 XCF_IORD 20 REG_GND 21 REG_GND 22 CF_D13 23 CF_A05 24 CF_D12 25 E 26 CF_D07 27 CF_A08 28 CF_D08 29 CF_A07 30 CF_D03 31 CF_A02 32 CF_3.3V 33 CF_3.
1 2 3 4 5 6 7 8 A A Note:IC7801 and AF-111 flexible complete board are not supplied, but they are included in ALX-6270 (AF module).
1 2 3 4 5 6 7 8 A A D GYVCC LN6212 REG_GND LN6211 INT_FLASH_FULL LN6210 INT_FLASH_CHARGE LN6209 DETECT LN6208 EVER_3.
1 2 3 4 5 6 7 8 BR_Y2 pin1 LND001 BR_Y2 pin2 LND002 BR_Y1 BR_Y2 LND034 BR_Y1 LND033 BR_P2 LND032 BR_P1 LND031 ACTUATOR (YAW) BR_Y1 BR_P2 LND003 BR_P2 LND004 BR_P1 LND005 VBRA5a LND006 Pout1p LND007 Pout2n LND008 Pout2p LND009 Pin_Y LND010 Pout4p LND011 Pout4n LND012 Pout3p LND013 Pout3n LND014 Pin_P pin15 LND015 Pout1n pin16 LND016 VBRA5b ACT-001 FLEXIBLE BR_P1 A LND001-LND002 Page 4-30 of Level 2 VBRA5 POUT1P A POUT2N POUT2P PIN_Y POUT4P POUT4N POU
1 pin18 2 LND018 NC LND017 FM- LND016 FM- 4 3 1 M903 (APERTURE MOTOR) FM+ LND013 IRIS_PI_E_2 LND012 IRIS_PI_K A LND010 FM- LND009 FM- LND001-LND010 Page 4-31 of Level 2 IRIS_PI_E_2 IRIS_PI_K IRIS_PI_E_1 LND010 IRIS_PI_A LND009 IRIS_PI_C IRIS_PI_A CN7701 10P xMF_PULSE_2 xMF_PULSE_1 LND007 FM+ LND006 NC LND005 IRIS_PI_E_2 LND004 IRIS_PI_K LND003 IRIS_PI_E_1 IRIS_PI_C pin2 LND002 IRIS_PI_A IRIS_PI_E_1 2 IRIS_PI_A pin1 3 IRIS_PI_E_1 4 IRIS_PI_K PH6101 GP1S3
1 1 4 3 2 Note: BZ901 and J901 are not included in RM-096 flexible complete board.
1 2 3 4 5 6 8 7 AM-013(19/19) CN3530 pin1 LN5901 pin2 LN5902 LN5903 A Page 4-25 of Level 3 LVDD1 LENS_SI LN5904 LN5905 XCS_LENS VDD VCC CS_LM GRP_ON LN5910 LN5911 FEN LMCK LN5912 LN5913 RWLM LN5914 B LN5915 MODE LMSIN LN5916 LN5917 GND LMOUT LN5918 LN5919 GND GND C D pin50 LN5950 pin51 LN5951 LVDD0 5 LVDD0 CSLM LN5986 LVDD0 6 LVDD0 GRP_ON pin7 LN5987 LVDD0 7 LVDD0 FEN pin8 LN5988 LVDD0 8 LVDD0 LMCK 9 LSOUT RWLM 10 REG_GND MODE 11 CSLNS LMSIN
1 4 3 2 1 pin1 LN7401 pin2 LN7402 LN7403 COM0 COM0 SEG20 SEG20 B SEG18 SEG18 SEG16 SEG16 SEG14 SEG14 SEG12 SEG12 SEG10 SEG10 SEG8 SEG8 SEG6 SEG6 LN7419 SEG4 SEG4 SEG2 SEG2 SEG0 SEG0 COM2 COM2 pin28 LN7428 pin29 LN7429 D COM1 COM1 LN7426 LN7427 COM3 COM3 LN7424 LN7425 SEG1 SEG1 LN7422 LN7423 SEG3 SEG3 LN7420 LN7421 SEG5 SEG5 LN7418 C SEG7 SEG7 LN7416 LN7417 SEG9 SEG9 LN7414 LN7415 SEG11 SEG11 LN7412 LN7413 SEG13 SEG13 LN7410 LN7411 SEG15
1 2 3 4 5 6 7 8 A A C6306 XX EVER_3.3V LN6318 VDD LN6317 VCC LN6316 CS_LM R6301 100k C6302 4.7u 6.3V C6303 10u 6.3V Q6301 2SA1577-T106-R LED DRIVE R6309 XX EVER_4.
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 1 2 3 4 5 6 8 7 FLASH UNIT (FL62700) is replaced as block, so that there PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted.
1 A 2 pin51 LN7251 pin50 LN7250 LN7249 3 DGND LN7239 DGND DGND CCD_RB_D10 CCD_RB_D8 CCD_RB_D6 LN7232 LN7231 CCD_RB_D4 LN7230 LN7229 CCD_RB_D2 LN7228 C LN7227 AM-013 (16/19) CCD_RB_D0 LN7226 LN7225 CN2602 Page 4-22 of Level 3 CCD_G_D10 LN7223 CCD_G_D8 LN7221 CCD_G_D6 LN7220 LN7219 CCD_G_D4 LN7217 CCD_G_D2 LN7215 CCD_G_D0 LN7214 D LN7213 XTGVD LN7211 XCS_AFETG_G LN7209 AN_SCK LN7208 LN7207 XAN_RST LN7206 LN7205 TGCLK LN7203 E pin2 LN7202 pin1 LN7201 DGND
1 2 3 4 5 7 6 8 10 9 11 12 A A B B 1pin LN6701 REG_GND LN6703 XCF_CD1 LN6704 LN6705 XCF_CD2 LN6706 LN6707 XCF_IOWR LN6708 LN6709 XCF_REG LN6710 LN6711 XCF_RST LN6712 LN6713 CF_RDY LN6714 LN6702 C LN6715 LN6717 REG_GND LN6719 CF_3.
2 1 3 4 5 6 7 8 S9106 (MODE DIAL) D9105 SML-210LT-T86 (SELF-TIMER) LN9107 EXT_FLASH_F3 LN9108 EXT_FLASH_F2 LN9109 EXT_FLASH_TRX LN9110 SELFLED_A LN9111 SELFLED_K LN9112 XDIAL_1_A LN9113 XDIAL_1_B XS2 LN9114 LN9115 XS1 LN9116 GND LN9117 XKEY_MAT_SEL_1 LN9118 IN2_DZOOM IN3_EXP LN9119 C D LN9120 IN0_ISO LN9121 IN1_AEL LN9122 XKEY_MAT_SEL_2 LN9123 IN3_DRV LN9124 IN3_VTN_DET LN9125 XKEY_MAT_SEL_3 LN9126 XPOPUP_DET_SW LN9127 XPOPUP_DET_COM LN9128 NC LN9129 PGN
4 3 2 1 S9501 A A 4 3 2 1 A A POWER OFF 2 1 3 4 ON B B pin1 LN9501 XPOWER_SW pin2 LN9502 DGND LN9504 XKEY_MAT_SEL_2 B S9202 pin6 C LN9201 XPOPUP_COM LN9202 EGND LN9203 XPOPUP_SW LN9206 XAF_MODE_COM LN9205 EGND LN9204 XAF_MODE_SW_A 1 3 2 D9201 XX XPOPUP_SW_IN0 1 2 XKEY_CROSS_COM_1 LN9506 XKEY_MAT_IN_6 LN9507 XKEY_FUNC_COM LN9508 XKEY_CROSS_C XKEY_CROSS_U XKEY_CROSS_D LN9511 XKEY_CROSS_L pin11 LN9512 XKEY_TEBURE_COM pin12 LN9513 XKEY_CROSS_COM_2
4-3.
4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS (ENGLISH) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • • : Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’ patterns are not indicated) • Through hole is omitted. • There are a few cases that the part printed on diagram isn’t mounted in this model. • C: panel designation • Chip parts.
IS-026 (6 layers) : Uses unleaded solder.
Printed wiring boards of the AM-013 board is not shown. Pages 4-43 and 4-44 are not shown.
LF-056 (2 layers) : Uses unleaded solder.
MM-076 (2 layers) : Uses unleaded solder.
GY-008 (1 layer) : Uses unleaded solder.
HOL-004 (2 layers) : Uses unleaded solder. HOL-004 FLEXIBLE BOARD Note: HOL-004 flexible complete board and all mounted parts are not supplied, but they are included in slider unit.
AFP-003 (1 layer), AP-031 (1 layer) : Uses unleaded solder. AFP-003 FLEXIBLE BOARD AP-031 FLEXIBLE BOARD Note: AFP-003 flexible complete board and all mounted parts are not supplied, but they are included in AF driving unit. Note: AP-031 flexible complete board and all mounted parts are not supplied, but they are included in aperture unit.
SLK-003 (1 layer), RM-096 (1 layer) : Uses unleaded solder. SLK-003 FLEXIBLE BOARD Note: SLK-003 flexible complete board is not supplied, but this is included in charge base plate B assy.
05 1 LN5988 LN5987 LN5986 LN5985 LN5984 LN5983 LN5901 LN5902 LN5903 LN5904 LN5905 LN5906 LN5907 LN5908 LN5909 LN5910 LN5911 LN5912 LN5913 LN5914 LN5915 LN5916 LN5917 LN5918 LN5919 LN5920 LN5921 LN5922 LN5923 LN5924 LN5925 LN5926 LN5927 LN5928 LN5929 LN5930 LN5931 LN5932 LN5933 LN5934 LN5935 LN5936 LN5937 LN5938 LN5939 LN5940 LN5941 LN5942 LN5943 LN5944 LN5945 LN5946 LN5947 LN5948 LN5949 LN5950 LN5951 1 4 LN5982 1 CN5903 5 LN5981 18 R5908 14 10 R5907 CN5904 CN5902 1 4 1 1 3 D5907 5
AE-031 (2 layers) : Uses unleaded solder. AE-031 FLEXIBLE BOARD 1 18 LN6301 LN6302 LN6303 LN6304 LN6305 LN6306 LN6307 LN6308 LN6309 LN6310 LN6311 LN6312 LN6313 LN6314 LN6315 LN6316 LN6317 LN6318 1-873-785 AE-031 C R6302 C6301 R6305 C6304 1 C6305 R6303 R6307 C6303 R6306 R6309 E 6 P C6302 B CN6301 C6306 Q6301 Note: AE-031 flexible complete board and all mounted parts are not supplied, but they are included in PENTA unit.
ST-196 (2 layers) : Uses unleaded solder. ST-196 BOARD (SIDE B) ST-196 BOARD (SIDE A) CN6501 12 1 3 1 5 CL6501 C6501 T6501 CL6502 C901 CHARGING CAPACITOR C6502 2 A 4 LD6502 D6501 LD6501 K CL6503 R6513 CL6504 C6504 D6502 K R6515 R6510 C6507 R6516 LD6503 C6506 R6501 IC6501 5 6 11 10 1 A (For Discharge) EVER_3.
NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST (ENGLISH) NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied.
5. REPAIR PARTS LIST DISASSEMBLY 5-1. EXPLODED VIEWS HARDWARE LIST 5-1-1. OVERALL SECTION ns: not supplied #23 #23 Rear Cover Section (See page 5-4) 5 4 #2 Main Board Section (See page 5-5) #2 #23 Front Cover Section (See page 5-3) #2 6 7 #23 #2 3 2 ns 1 Ref. No. 1 2 3 4 5 Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-2. FRONT COVER SECTION ns: not supplied #75 58 #75 #75 57 51 54 53 ns 56 55 52 59 Ref. No. Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-3. REAR COVER SECTION ns: not supplied 111 109 110 108 #75 ns 104 (12mm x 20mm) 107 LCD901 #108 106 105 (5mm x 5mm) #75 103 102 #75 CAUTION: For the part of 104 and 105, cut SHEET, ADHESIVE (2649-300-01) into the desired length and use it. 101 CAUTION: 104番，105番は，接着紙 （2-649-300-01） を切って使用。 Ref. No. Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-4. MAIN BOARD SECTION ns: not supplied 155 154 #75 151 #75 AM -01 Shutter Unit Section (See page 5-6) 152 ns #75 BH3001 (Note) BT901 (Note) 153 3 #109 ! : BT901 (BATTERY, STORAGE, LITHIUM) Board on the mount position. (See page 4-44 on level 3) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-5. SHUTTER UNIT SECTION ns: not supplied 203 Tebure Unit Section (See page 5-7) ns Bottom Frame Section (See page 5-8) 204 202 (8mm x 8mm) #23 #23 #110 #23 #14 ns 201 #59 #23 #84 CAUTION: For the part of 204, cut WOVEN (T0.25), FABRIC NON (3-076-631-01) into the desired length and use it. CAUTION: 204番は，T0.25ヒメロン （3-076-631-01） を切って使用。 Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST 5-1-6. TEBURE UNIT SECTION 259 (including IC4303 (CCD imager) and IS-026 board) (Note 1, 2) 258 #111 (including IS-027 flexible board) 261 260 254 (including ACT-001 flexible board and HOL-004 flexible board) 255 #87 #111 #87 257 253 252 255 256 252 253 #87 255 253 251 252 Note 1: Be sure to read “Precautions for Replacement of Imager” on page 4-2 when changing the imager. Note 1: イメージャの交換時は4-3ページの“イメージャ 交換時の注意”を必ずお読みください。 Note 2: Refer to “2-11.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-7. BOTTOM FRAME SECTION Top Cover Section (See page 5-9) #2 #112 304 303 Battery Holder Section (See page 5-11) (15mm x 9mm) #113 305 #2 #23 #110 #23 Terminal Holder Section (See page 5-12) #59 302 301 #110 #23 CAUTION: For the part of 303, cut WOVEN (T0.25), FABRIC NON (3-076-631-01) into the desired length and use it. #86 #23 CAUTION: 303番は，T0.25ヒメロン （3-076-631-01） を切って使用。 Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-8. TOP COVER SECTION #75 359 356 #14 #114 #75 #75 #115 #75 355 358 354 357 353 (15mm x 9mm) Flash Unit Section (See page 5-10) 352 CAUTION: For the part of 353, cut WOVEN (T0.25), FABRIC NON (3-076-631-01) into the desired length and use it. 351 CAUTION: 353番は，T0.25ヒメロン （3-076-631-01） を切って使用。 Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-9. FLASH UNIT SECTION ns: not supplied 409 410 411 408 412 #109 413 #23 407 406 ns 405 404 403 414 (5mm x 10mm) White (Note) Pink (Note) Note: About the arrangement of harness, refer to HELP 10. 401 Black (Note) 402 CAUTION: For the part of 414, cut SHEET, ADHESIVE (2-649-30001) into the desired length and use it. Note: 配線についてはHELP10を参照し てください。 CAUTION: 414番は，接着紙（2-649-300-01） を切って使用。 • Refer to page 5-1 for mark 0. Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-10. BATTERY HOLDER SECTION ns: not supplied #109 459 #108 458 461 #75 #109 462 463 460 457 464 456 467 #116 453 BT902 455 468 #23 #23 ns 466 ns #75 #23 465 454 ns 452 451 C901 • Refer to page 5-1 for mark 0. Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-11. TERMINAL HOLDER SECTION ns: not supplied #14 #23 Mirror Box Section (Penta Unit) (See page 5-13) 506 (including EYE-006 flexible board) 505 BZ901 507 (Note) 514 509 508 J901 512 #59 510 513 (Note) 511 ns 504 503 (including AF-111 flexible board) #23 J902 501 502 #88 #23 Note: When the RM-096 flexible board’s suffix No. is qs, part of 513 is not used. Note: RM-096フレキシブル基板の末尾がqsの時には，513番は使 用していません。 • Refer to page 5-1 for mark 0.
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-12. MIRROR BOX SECTION (PENTA UNIT) #117 #117 651 ns (including AE-031 flexible board, IFL-003 flexible board and LED-001 flexible board) 659 655 - 658 (Note 2) 652 (Note 1) 658 (Note 2) 653 (Note 1) 654 Mirror Box Section (Sub Unit-1) (See page 5-14) Note 1: Refer to page 1-2 “1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUS PLATE” when SI screen or focus plate are exchanged. Note 1: SIスクリーンまたは焦点板を交換する際は，1-5 ページの「1-5.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-13. MIRROR BOX SECTION (SUB UNIT-1) 710 (including AP-031 flexible board) 701 Mirror Box Section (Sub Unit-2) (See page 5-15) 708 709 #12 707 704 705 706 703 716 723 702 #23 711 #92 715 #91 712 713 #90 719 #89 720 722 #89 714 721 718 717 (including AFM-002 flexible board and AFP-003 flexible board) Ref. No. Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST HARDWARE LIST DISASSEMBLY 5-1-14. MIRROR BOX SECTION (SUB UNIT-2) ns: not supplied 752 (including BL-016 flexible board) 753 #23 ns #75 773 751 ns 772 754 755 756 757 758 #93 762 763 770 771 #93 759 #23 760 761 765 767 #93 768 #23 764 (including SLK-003 flexible board) 769 766 #23 Ref. No. 751 752 Part No. Description Ref. No.
Electrical parts list of the AM-013 board is not shown. Page 5-16 to 5-22 is not shown.
GY-008 IS-026 LF-056 MA-450 MM-076 RM-096 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. A-1437-492-A GY-008 FLEXIBLE BOARD, COMPLETE ****************************** Part No.
ST-196 Ref. No. Part No. Description Ref. No. A-1437-493-A ST-196 BOARD, COMPLETE ********************** 3-277-350-01 TAPE (62300), CAPACITOR FIXED < CAPACITOR > 0* C901 C6501 C6502 C6504 C6506 C6507 1-114-603-11 1-119-667-11 1-100-611-91 1-162-919-11 1-165-908-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 250uF 22uF 22uF 22PF 1uF 1-164-360-11 CERAMIC CHIP 0.1uF 20% 5% 10% 330V 10V 6.
Checking supplied accessories. Note: This item is supplied with the unit as an accessory, but is not prepared as a service part.
HARDWARE LIST (1/6) #1: M1.7 X 2.5 (Black) 2-635-562-11 #2: M1.7 X 4.0 (Black) 2-635-562-31 #3: M1.7 X 2.5 (Red) 2-660-401-01 1.7 2.5 1.7 4.0 #5: M1.7 X 3.5 (Tapping) (Black) 3-080-204-01 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 1.7 1.7 4.0 #13: M1.7 X 2.5 (Tapping) (Silver) 3-085-397-01 1.7 2.5 5.0 #16: M1.4 X 2.5 (Silver) 2-586-337-01 2.5 #19: M1.2 X 4.0 (Tapping) (Red) 3-086-156-21 1.4 1.5 2.5 1.4 1.4 1.5 #18: M1.4 X 2.5 (Silver) 2-635-591-21 1.7 2.2 1.7 1.7 #15: M1.4 X 1.
HARDWARE LIST (2/6) #21: M1.4 X 3.0 (Black) 2-662-396-21 #22: M1.7 X 5.0 (Tapping) (Silver) 3-083-261-01 #23: M1.7 X 4.0 (Tapping) (Black) 3-080-204-11 1.7 1.4 #25: M1.7 X 3.0 (Black) 2-635-562-21 1.7 4.0 5.0 3.0 #26: M1.4 X 2.0 (Silver) 2-635-591-11 3.0 3.0 #36: M3.0 X 6.0 (Silver) 4-886-821-11 3.0 4.0 6.0 6.0 #39: M2.6 X 5.0 (Tapping) (Black) 7-685-791-09 #38: M3.0 X 20.0 (Tapping) (Silver) 7-685-651-79 2.0 4.5 #35: M4.0 X 6.0 (Tapping) (Silver) 3-975-291-02 8.0 #37: M2.0 X 6.
HARDWARE LIST (3/6) #41: M3.0 X 8.0 (Tapping) (Silver) 3-065-748-01 #42: M2.0 X 4.0 (Tapping) (Silver) 7-628-253-00 #43: M1.7 X 4.0 (Red) 2-660-401-31 2.0 3.0 8.0 #46: M1.7 X 3.0 (Red) 2-660-401-11 #49: M2.0 X 4.0 (Black) 2-630-005-31 3.0 #50: M2.0 X 3.0 (Red) 2-891-494-11 2.0 4.0 #48: M1.7 X 2.5 (Silver) 3-973-497-91 1.4 1.7 3.0 1.7 3.0 #47: M1.4 X 3.0 (Tapping) (Silver) 2-665-774-01 1.4 2.5 1.7 4.0 4.0 #45: M1.4 X 2.5 (Silver) 2-587-151-01 #44: M1.7 X 3.
HARDWARE LIST (4/6) #61: M3.0 X 10.0 (Black) 7-682-549-09 #62: M2.0 X 3.0 (Silver) 3-080-202-21 3.0 10.0 2.0 12.5 #66: M1.4 X 1.4 (Silver) 2-635-591-41 1.4 3.5 #76: M1.7 X 4.0 (Tapping) (Silver) 2-666-551-11 1.7 3.5 1.7 4.0 #80: M1.4X 2.0 (Black) 3-279-411-01 #79: M1.4X 2.0 (Silver) 2-587-151-11 1.4 1.4 3.5 2.0 #75: M1.7 X 3.5 (Tapping) (Silver) 2-666-551-01 #78: M1.4 X 3.5 (Red) 3-208-537-11 1.4 1.4 1.7 1.2 #72: M1.4 X 2.0 (Silver) 4-663-621-41 2.0 6.0 #77: M1.2 X 5.
HARDWARE LIST (5/6) #82: M1.4 X 1.4 (Silver) 3-272-251-01 #81: M1.7 X 2.5 (Silver) 2-515-756-01 1.7 1.4 2.5 #86: M1.7 X 4.0 (Tapping) (Silver) 2-695-434-21 2.5 #97: M1.4 X 2.5 (Black) 2-662-396-31 1.4 8.0 1.4 2.5 #99: M2.5 X 6.0 (Tapping) (Silver) 3-776-750-02 3.8 8.0 #96: M1.4 X 2.5 (Silver) 2-587-151-21 3.0 1.7 #98: M3.0 X 8.0 (Silver) 3-077-331-01 2.5 3.9 #95: M3.0 X 8.0 (Tapping) (Black) 7-685-646-79 4.0 3.5 2.0 1.7 3.5 #94: M1.7 X 4.0 (Black) 2-515-483-31 1.7 #92: M2.0 X 3.
HARDWARE LIST (6/6) #102: M2.6 X 8.0 (Black) 7-621-284-30 #101: M2.0 X 5.0 (Silver) 7-621-555-39 2.6 2.0 5.0 #105: M2.0 X 4.0 (Red) 2-891-494-31 10.0 #106: M2.0 X 6.0 (Black) 3-713-786-11 #107: M2.0 X 5.0 (Silver) 3-032-750-01 2.0 4.0 6.0 #109: M1.7 X 3.0 (Black) 2-515-483-21 #110: M2.0 X 3.0 (Black) 2-630-005-21 5.0 5.5 #117: M1.7 X 4.5 (Tapping) (Silver) 2-695-429-31 1.7 1.7 3.0 #112: M1.4 X 5.0 (Black) 2-178-410-11 1.7 4.0 1.4 5.0 #115: M1.4 X 3.
Reverse 985224431.pdf Revision History Ver. Date 1.0 2007.12 DSLR-A200_L2 History Official Release Contents — S.M. Rev.
