INSTRUCTION MANUAL ’12.
Introduction Thank you for your purchase of "SO-04D". For proper use of the SO-04D, read this manual carefully before and while you use the SO-04D. Before using the terminal ● SO-04D supports W-CDMA, GSM/GPRS and Wireless LAN Systems. ● Because a terminal operates using radio frequencies, it cannot be used inside a tunnel, underground, in a building or other locations where radio waves do not reach the terminal, in locations with weak radio wave condition, or outside of the FOMA's service area.
Supplied accessories ･ AC Adapter Cable SO04 (with warranty) Supplied accessories ･ SO-04D (with warranty) ･ Desktop Holder SO12 (with warranty) ･ microSD card (2GB)* (Sample) (with manual) ･ クイックスタートガイド (Quick Start Guide) (In Japanese only) * Inserted in the terminal when purchased. クイック スタート ガイド ･ SO-04D のご利用にあたっての注意事項 安全上／取り扱い上のご注意 ･ Stereo Headset with Microphone (Sample) (with manual) For details on optional devices, see "Optional and related devices" (P.
About manuals of SO-04D In addition to this manual, the operations of SO-04D are described in " クイックスタートガ イド (Quick Start Guide)" (in Japanese only) and "Instruction Manual" application of the terminal. " クイックスタートガイド (Quick Start Guide)" (Supplied accessories) The initial operations and settings after purchasing the terminal, screen view contents and operations of main function are explained.
Operation descriptions In this manual, each key operation is described with p, x, y, t, m, k. And selection operations of the icons or function items on the touch panel are described as follows. ･ Please note that "SO-04D" is called "the terminal" in this manual. ･ In this manual, explanations for "docomo" as Home application are provided. To switch the Home applications, see "Learning Home screen" (P.66). Description From the Home screen, tap t and tap [Settings].
Contents/Precautions Contents Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 About manuals of SO-04D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Notes on usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings → P.107 Mail/Internet → P.141 File management → P.158 ・ Viewing the setting menu ................................................................107 ・ docomo service ....................................................................................107 ・ Xperia™ ............................................................................... 108 ・ Wireless & networks ............................................................................109 ・ Call settings...................................
・ Shooting with the camera ................................................................172 ・ Capturing the screenshot .................................................................191 ・ Playing multimedia content.............................................................192 ・ Viewing photos/videos......................................................................193 ・ Playing YouTube video.......................................................................
Contents/Precautions Notes on usage ･ The terminal does not support i-mode sites (programs) or i-Dppli. ･ The terminal automatically performs communication for synchronizing data, checking the latest software version, maintain connection with the server, etc. If you transmit a large amount of data such as downloading applications or watching movie, a packet communication charge becomes high. Subscription of packet flatrate service is highly recommended. ･ Public mode (Driving mode) is not supported.
･ Battery is built into the terminal and cannot be replaced by yourself. ･ To use tethering, subscription of sp-mode is required. ･ Packet communication charge when using tethering varies depending on the charging plan you use. Subscription of packet flat-rate service is highly recommended. ･ For details on usage charge, etc., refer to http:/ /www.nttdocomo.co.jp/ .
Safety Precautions (Always follow these directions) ■ Indicates prohibited actions. ■ For safe and proper use of the terminal, please read the "Safety Precautions" prior to use. Keep the Manual in a safe place for future reference. ■ ALWAYS observe the safety precautions since they intend to prevent personal injury or property damage. ■ The following symbols indicate the different levels of injury or damage that may result if the guidelines are not observed and the terminal is used improperly.
1. Handling the terminal, AC Adapter cable, Desktop Holder and UIM (general) WARNING Don’t DANGER Don’t Don’t Do not use, store or leave the equipment in hot places (e.g. by the fire, near a heater, under a kotatsu, in direct sunlight, in a car in the hot sun). (including the event that you ware the equipment in the pocket of your clothes, etc.) Doing so may cause fire, burns or injury. Do not place equipment inside cooking appliance such as a microwave oven or highpressure containers.
Do If you notice anything unusual about the equipment such as an unusual odor, overheating, discoloration or deformation during operation, charging or storage, immediately perform the following measures. ・Remove the power plug from the power outlet. ・Power off the terminal. Failure to do so may cause fire, burns, injury or electric shock. Do CAUTION Don’t Do not place on an unstable or inclined platform. Doing so may cause the device to fall and cause injury.
2. Handling the terminal ■ The internal battery for the terminal is as follows. Display Li-ion 00 Type of Battery Lithium Ion Battery Do not throw the terminal into fire. Doing so may cause internal battery to ignite, explode, overheat or leak. Do not allow a foreign substance such as water and other liquids, metal parts, or flammables to get in the UIM or microSD card insertion slot on the terminal. Doing so may cause fire, burns, injury or electric shock.
Do Do Do Power off the terminal in a place where the use is prohibited such as in airplane or hospital. Failure to do so may affect electronic equipment and electronic medical equipment. If you set the automatic power-on function, cancel it before powering off the terminal. Follow the instructions of each medical facility for the use of mobile phones on their premises. Prohibited acts such as mobile phone usage on board an airplane may be punished by law.
Do If the internal battery leaks or hears an unusual odor, immediately stop using and move it away from fire. The leaking liquid may ignite fire, catch fire, or explode. Do CAUTION Don’t Don’t Don’t Don’t Do not swing the terminal around by holding the antenna or strap. The terminal may hit you or others and cause accident such as injury. Do Do not use damaged terminal. Doing so may cause fire, burns, injury or electric shock.
3. Handling the adapter and desktop holder Don’t WARNING Don’t Do not use the microUSB cable if it is damaged. Doing so may cause fire, burns or electric shock. Don’t Do not use the AC adapter cable or the desktop holder in a very humid or steamy place such as bathroom. Doing so may cause fire, burns or electric shock. Don’t Don’t Don’t Don’t No wet hands Do DC adapter is only for a negative ground vehicle. Do not use DC adapter for a positive ground vehicle.
Do Hold the AC adapter, not the microUSB cable, when you remove the power plug from the power outlet. Failure to do so may cause fire, burns or electric shock. Unplug Remove the power plug from the power outlet when not used for a long period of time. Failure to do so may cause fire, burns or electric shock. Unplug If liquid such as water gets into the adapter, immediately remove it from the power outlet. Failure to do so may cause fire, burns or electric shock.
Do If you need to use electronic medical equipment other than implantable cardiac pacemaker or implantable cardioverter defibrillator outside medical facilities such as treating at home, check with the relevant medical electronic equipment manufacturer whether the operation may be affected by radio waves. The radio waves from the terminal may affect the performance of electronic medical equipment. 6.
Handling precautions ■ ･ Common precautions ･ ･ ･ Clean the terminal with a dry soft cloth (such as used for cleaning eyeglasses). - Do not rub it roughly with a dry cloth. The display may be damaged. - Drops of water or dirt left on the display may cause stains. - Do not use alcohol, thinner, benzine, cleaning detergent, etc. to clean the terminal. These chemicals may erase the printing on the terminal or cause discoloration. Clean the terminals occasionally with a dry cotton swab.
■ The terminal precautions ･ ･ ･ Do not press touch panel surface forcibly, or not operate with a sharp-pointed objects such as nail, ballpoint pen, pin, etc. Doing so may cause damage of touch panel. Do not use the terminal in extremely hot or cold places. Use the terminal where the temperature ranges between 5 ℃ and 40 ℃ (limited to the temporary use in a bathroom etc. when temperature is 36 ℃ or more) and humidity ranges between 45% and 85%.
･ ･ Even if the operating time of the terminal varies depending on the operating conditions and other factors, when the length of time you can use the terminal with a fully charged battery becomes unusually short, it is time to replace the internal battery. For replacement of internal battery, contact "General Inquiries" on the last page of this manual or the DOCOMO-specified repair office. Charge the battery pack in an environment with the proper ambient temperature (5 ℃ to 35 ℃ ).
･ ･ Note down the information saved in the UIM in a separate note and keep it safely. Under no condition will DOCOMO be held liable for any damaged or lost data saved in the terminal. Take an expended UIM to sales outlet such as docomo Shop for proper disposal in order to protect the environment. ･ Do not carelessly damage, contact, or short-circuit an IC. ･ ･ ･ Doing so may cause data loss or malfunction. Do not drop a UIM or subject it to impact. Doing so may cause malfunction.
･ Bluetooth cautions The operating frequency band of the terminal is used by industrial, scientific, consumer and medical equipment including microwave ovens, premises radio stations for identifying mobile units used in the manufacturing lines of plants (radio stations requiring a license), specified low power radio stations (radio stations requiring no license) and amateur radio stations (hereinafter referred to as "another station").
･ - If the device causes radio interference to specified low power radio stations or amateur radio stations, contact "General Inquiries" on the last page of this manual. 5.6GHz band 5 GHz device cautions Channels available in Japan are as follows. Channel No. (Ch) Frequency (MHz) 5.2GHz 36 5,180 band 38 5,190 40 5,200 44 5,220 46 5,230 48 5,240 5.3GHz 52 5,260 band 54 5,270 56 5,280 60 5,300 62 5,310 64 5,320 5.
･ ･ ･ If you remove the screws and alter the inside of the terminal, the technical regulations conformity certification becomes invalid. Do not use the terminal with the certification invalid, as it is a violation of the Radio Law. Be careful when using the terminal while driving. Using a handheld mobile phone while driving will result in a penalty. However, absolutely necessary cases such as rescue of a sick person or maintaining public's safety are exempted.
Part names and functions ab c de g h i t o q j k l u r f m n a Light sensor : Used for auto controlling of the screen brightness. b Proximity sensor : Turns on or off the touch screen to prevent misoperation during a call. c Ear speaker d Front camera lens e Notification LED f Touch screen g GPS antenna section* h Camera lens i Xi/Wi-Fi/Bluetooth antenna section* j Photo light k mark l Second microphone : Reduce noise to make easy to listen.
UIM The UIM is an IC card recorded user information such as your phone number etc. If the UIM is not inserted to the terminal, you cannot use some functions (phone function, etc.) of the terminal. ･ In this terminal, the UIM (blue) is not available. If you have a UIM (blue), bring it to the nearest docomo Shop to replace. ･ Do not use docomo mini UIM card attaching with conversion adapter. Doing so may cause malfunction. ･ When inserting/removing the UIM, make sure to power off the terminal.
2 Push the tray straight to the end, close the UIM card slot cover, and then confirm there is no gap between the body and cover. microSD card Removing UIM 1 Open the UIM card slot cover, hook your fingernail by the projection part on the edge of the tray to pull the tray straight out, and then remove the UIM. You can use microSD card for any other compatible devices. ･ The terminal supports microSD card of up to 2GB, and microSDHC card of up to 32GB (As of February, 2012).
Removing microSD card Make sure to unmount (disable reading and writing) microSD card before removing. 1 From the Home screen, tap t and tap [Settings]u[Storage]u[Unmount SD card]. ･ 2 Close the microSD card slot cover and confirm there is no gap between the body and cover ( ). When unmounting microSD card, " SD card safe to remove" appears in the status bar to notify that reading or writing from/onto microSD card becomes disabled.
4 Close the microSD card slot cover and confirm there is no gap between the body and cover. ❖Information ･ If you remove the microSD card without unmounting, " SD card unexpectedly removed" appears in the status bar and files may be damaged or data may be lost. Charging The battery pack is not full charged when you purchased the terminal. The following time varies by the internal battery condition or operating environment. For details, see (P.256).
Charging ･ The supplied AC adapter's power plug is compatible with AC 100 V to 240 V. For using the terminal overseas, a plug adapter that fits the electrical outlets in the country you stay is needed. Do not use an electrical transformer for overseas use to charge the terminal. ･ Use the supplied AC Adapter cable for charging. ･ When charging starts, the notification LED turns on in red/orange/green. Green means the remaining battery level reaches 90% or more.
3 Insert the terminal to the desktop holder. 4 After charging is finished, remove the terminal from the desktop holder, and then remove the AC adapter from the power outlet. ･ Check the connecting direction to connect correctly. Wrong connection may cause damage. ❖Note ･ The battery cannot be charged by connecting the desktop holder and a PC.
Charging with AC adapter Charging with a PC 1 Open the microUSB connecting jack cover, and insert the microUSB cable horizontally with the microUSB plug engraved side facing down into the microUSB connecting jack of the terminal. 1 Open the microUSB connecting jack cover, and insert the microUSB cable horizontally with the microUSB plug engraved side facing down into the microUSB connecting jack of the terminal.
･ Check the connecting direction to connect correctly. Turning power on/off Wrong connection may cause damage. Turning power on 1 Press and hold p for over a second. ･ 2 The key unlock screen appears. Deactivate the key lock. ･ For deactivating the key lock, see "Unlocking the keys" (P.39). ❖Information ･ The first time you turn on, "Setup guide" (P.39) appears. ･ If you activate the screen lock (P.127) or SIM card lock (P.
Turning power off 1 Phone options menu appears. Tap [Power off]. Tap [OK]. Performing force-quit You can force the terminal quit if the screen does not respond or the power cannot be turned off. 1 Press and hold p and upper of m at the same time for approximately 10 seconds. Lift up your finger after the terminal vibrates 3 times. ･ Press and hold p for over a second. ･ 2 3 2 The terminal is forced quit and the power turns off.
Unlocking the keys A key unlocking screen appears when turning the power on or the backlight on by pressing p. 1 Touch and drag it laps over. to until Initial settings (Setup guide) When you turn on the terminal for the first time, Setup guide appears to set up the display language, wireless network, online services, etc. and to import contacts. ❖Information ･ You can set or change the items later as required. Key lock ❖Information ･ appears on the right until you touch .
4 Tap 5 Tap 6 Tap 7 8 9 ･ ･ ･ The wireless network screen appears. Tap [Search for networks] to add Wi-Fi network. ･ Tap 11 Tap 12 Tap 13 Tap 14 Tap ･ ･ ･ . The import contacts screen appears. For information on import contacts, see "Using PhoneBookCopy" (P.94). ･ . Preferred applications screen appears. Tap either [doocmo applications] or [Xperia™ applications] to select. Tap 10 . Automatic renewal screen appears. Tap [Synchronize automatically] or [No thank you] to select.
Status bar A status bar appears at the top of the screen. In the status bar, the terminal status and notification are displayed. Notification icons appear on the left side, and the terminal status icons appear on the right side of the status bar. Status bar ❖Note ･ If you cancel the "status bar" of applications forcibly (P.130), operations may not be performed correctly. Status icon The main status icons displayed on the screen are as follows.
Facebook setting request notification Receiving/Downloading data Sending/Uploading data Bluetooth connection request notification Unmount microSD card to remove (reading/ writing unavailable) microSD card is removed Preparing microSD card/internal storage Installation is completed (when installing applications from Android Market, etc.
Opening/Closing the Notification panel Notification LED Notification LED provides information on the terminal status, incoming/receiving, etc. Notification panel LED status Status Red Flashing red 1 Drag the status bar downwards. ･ Tap x to close the notification panel. Clearing contents on the Notification panel 1 On the Notification panel, tap [Clear]. ❖Information ･ Some notifications cannot be cleared.
Basic operations Basic key operation x Back ･ Go back to the previous screen. Or ･ y Home ･ ･ t Menu ･ ･ close a dialog box, Option menu, or the Notifications panel. Close the software keyboard. Go to the Home screen. Touch and hold down to open a list of recently used applications. Open a list of options available in the Home screen or application. Touching and holding down when entering characters switches display/not display the software keyboard.
■ Flick Stroke the screen with your finger lightly and flick up/down/left/right. Flick operation is used to switch or scroll the screen. ❖Information ･ You can zoom in or out also by double-tapping or by tapping the zoom control icons ( / ). The zoom control icons may appear when you drag in any direction on the screen. Selecting items quickly from a list Tap the right end of the screen to display index characters with which you can search by Japanese syllabary and alphabetic order.
Marking or unmarking option checkbox Searching information in the terminal and web pages You can switch on/off of the option settings by marking or unmarking the checkboxes or radio buttons. ･ To switch on/off of the option setting, tap the checkbox or radio button. Enter a word in the search box to browse the information in the terminal or on the Internet.
Search settings Character entry You can set search engines to use for Quick search box or set search objectives in the terminal. 1 2 From the Home screen, tap then tap [Google Search]. , Tap t and then [Search settings]. ･ Google search A search settings screen appears. You can set the following items. Set whether to display search options when a search word is entered, or whether to reflect the previous search result in the search options.
■ ❖Information ･ You can change Input method (keyboard type) QWERTY keyboard Japanese characters can be entered in "Romaji input" mode. during character entry. Software keyboard For Japanese keyboard, there are 4 types of software keyboards: phonepad, QWERTY, Japanese syllabary and handwritten input. Portrait ❖Information ･ The key display of software keyboard varies depending on the entry screen, character mode or settings.
■ ･ Handwritten input Tap to display plug-in applications list. Tap [Contact Picker 2.3] to quote contacts to enter. ･ : Switch one-byte/two-byte character. ･ : Hide the software keyboard. Japanese characters can be entered in "Handwritten input" mode. ❖Information ･ The phonepad keyboard is set by default. Also, "Auto Portrait capitalization", "Word suggestions", "Error correction" and "Pop-up on key press" are set to on.
Icon Function / Display a pop-up window. Touch and / / / : Keyboard switch hold (two-byte)/ (one-byte) : Character mode switch : Display the setting screen for Japanese keyboard : Display plug-in applications list : Hide the software keyboard / Each time you tap, the character mode switches "Hiragana/Kanji/alphabets" → "Number" in order and a status icon, / appears in the / , etc. → status bar. / Display a one-byte/two-byte symbol list Touch and to enter them.
･ *2 Before the conversion is fixed, " 確定 (Fix)" is displayed. In some screens such as the search box or mail account registration screen, " 次へ (Next)", " 完 了 (Done)", " 実行 (Go)", etc. appear. Flick input is available by default. You can cancel by the following operation beforehand. a From the Home screen, tap t and tap [Settings]. b Tap [Language & keyboard] → [Xperia™ Japanese keyboard] → [Onscreen keyboard settings]. c Unmark [Flick input] checkbox.
❖Information ･ When a certain time is passed after the key tapped, the tapped key's highlighter goes off and you can enter a character assigned to the same key consecutively without tapping . ･ To switch upper/lower case or change to voiced/semi-voiced sound, tap . ･ Multitap text input is available by default. You can cancel by the following operation beforehand. a From the Home screen, tap t and tap [Settings]. b Tap [Language & keyboard] → [Xperia™ Japanese keyboard] → [Onscreen keyboard settings].
Icon Function / Display a one-byte/two-byte symbol list Touch and to enter them. Switch tabs to display hold smiley list to enter them. (a pictogram tab and deco-mail tab are also displayed when entering in sp-mode mail.) Move the cursor*1 : To the left. Touch and hold to move continuously. Or change the range for conversion. Move the cursor*1 : To the right. Touch and hold to move continuously. Or change the range for conversion.
3 Tap [On-screen keyboard settings]u [Choose key type]. 4 Tap any of [Static key resizing]/ [Key highlight while typing]/ [Dynamic key resizing with highlight]/[Off]. ■ ■ Dynamic key resizing with highlight Widen the key that is predicted for the next entry much further and highlight it. Static key resizing Widen frequent using key for easy tapping. ■ Off Display equally the width of each key.
3 Tap [On-screen keyboard settings]u[Select display keys]. ･ 3 Tap [On-screen keyboard settings]u[Keyboard customization]. 4 Tap a symbol you want to change and delete character previously set, then enter a character to display. When the assist keyboard (P.53) is set to "Off", [Select display keys] cannot be selected and you cannot change a displaying key. 4 Unmark the checkbox of the key you want to hide. 5 Tap [OK].
Entering characters on the Japanese syllabary keyboard You can use the software keys arranged according to the Japanese syllabary to enter Japanese characters in "Kana input" mode. The main functions of the touch-keys ･ To change character modes and other input operations, tap the following icons on the Japanese syllabary keyboard. Icon / Function Each time you tap, the character mode switches "Hiragana/Kanji" → "Alphanumeric" in order and a status → / / / / / icon, appears in the status bar.
Icon Function Appears in landscape view. One-byte/ two-byte symbol list can be displayed to enter them. Switch tabs to display smiley list to enter them. (a pictogram tab and deco-mail tab are also displayed when entering in sp-mode mail.) In Hiragana/Kanji input mode, conversion candidates can be displayed to enter. Activate online dictionary. Touch and You need to mark "Online dictionary" checkbox in the Japanese keyboard hold setting screen.
Icon / Function Each time you tap, the character mode switches "Hiragana/Kanji/alphabets" → "Number" in order and a status icon, / appears in the / , etc. → status bar. / Display a one-byte/two-byte symbol list Touch and to enter them. Switch tabs to display hold smiley list to enter them. (a pictogram tab and deco-mail tab are also displayed when entering in sp-mode mail.) Displayed before fixing character. Display word predictions or alphanumeric conversion candidates assigned to entered letter.
❖Information ･ When you enter character by handwritten input for ･ ･ ･ ･ ･ the first time, a screen indicating how to input appears. Tap [OK] or x. In handwritten input, hiragana, alphabet, number, some symbols can be entered. You can enter a character continuously without deleting entered character. For voiced sound and semi voiced sound mark, enter in the right upper part of the handwritten input screen.
Setting character entry For each type of keyboard, you can make settings related to character entry. 1 From the Home screen, tap t and tap [Settings]u[Language & keyboard]. 2 Tap [Xperia™ keyboard]/[Xperia™ Chinese keyboard]/[Xperia™ Japanese keyboard]. ･ Setting Japanese keyboard Common settings of software keyboard Make keyboard settings such as Key sound, Vibrate, etc. 1 The settings screen for each keyboard appears. Tap an item displayed on the screen to set.
Auto capitalization Set to capitalize automatically the top letter you enter in English input mode. 1 From the Home screen, tap t and tap [Settings]u[Language & keyboard]u[Xperia™ Japanese keyboard]. 2 Mark [Auto capitalization]. Keyboard skin settings You can change keyboard skin. 1 2 3 From the Home screen, tap t and tap [Settings]u[Language & keyboard]. Tap [Xperia™ Japanese keyboard] u[Select keyboard skin]. Select from displayed keyboards and tap [Set skin].
Setting Error correction ･ Error correction corrects mistyped characters and shows conversion candidates before conversion in one-byte alphabet input mode when entering characters with QWERTY keyboard. 1 From the Home screen, tap t and tap [Settings]u[Language & keyboard]. 2 3 Tap [Xperia™ Japanese keyboard]. Mark [Error correction] checkbox. Setting Auto space ･ When selecting English word suggestion, Auto space enters next to the entered character.
･ When entering characters, tapping [ 直変 (Direct conversion)] in the word suggestion field may give priority to some registered words. Editing user dictionary 1 On the user dictionary screen, select a word you want to edit. 2 3 Tap t and [Edit]. Edit the content and tap [Save]. ❖Information ･ To delete learned words individually, touch and hold a word you want to delete and tap [ 学習データ削除 (Delete learned word)].
4 5 6 Mark a dictionary you want to back up or restore from among [My words Japanese], [My words English], or [Learn words]. Tap [Go]. ･ When backing up, a screen asking whether to overwrite the user dictionary on the internal storage appears. When restoring, a screen asking whether to overwrite the user dictionary in the terminal appears. "Contact Picker 2.3" is a preinstalled plug-in application. 1 On a character entry screen, touch and hold . 2 3 4 Tap . Tap [Contact Picker 2.3].
4 5 Tap [Download new extensions]. Tap an application and follow the onscreen instructions. ❖Information ･ Marked plug-in applications in the POBox plug-in setting screen can be activated in the character entry screen. Checkboxes for preinstalled plug-in applications, "Contact Picker 2.3" is marked by default. POBox Touch User Guide You can view the detailed explanations on the high performance Japanese keyboard from the basic to application.
docomo Palette UI ❖Information Home screen Home screen is a start screen for using applications. You can personalize the Home screen by adding or moving, for example, application shortcuts and widgets, or changing the wallpaper. Learning Home screen Tapping y displays Home screen which consists of up to 12 screens you can use flicking left and right. a b ･ You can switch the home application between "docomo" and "Xperia™" in the terminal. "docomo" is set to the home application by default.
Displaying a list of home screens 1 From the Home screen, pinch-in. ･ A home screen list appears. ❖Information ･ At the left end home screen, tap y or from the Home screen, tap t and tap [Home screens] to display the list. ･ To return to the home screen, pinch-out, or tap y or x. Adding to the Home screen 1 2 ■ From the Home screen, tap t. Tap [Add]. ･ "Add to home screen" menu appears to change the Home screen.
Adding a widget to the Home screen 1 In "Add to home screen" menu, tap [Widget]. ･ A list of widgets appears. Calendar Contents Headline docomo location information Facebook Google Search Google+ Display the calendar. Display the latest contents information of music, video, ebook, etc. Display docomo location information application. View comments of members. Display the Quick search box. Display Google+, compose article to post. Home screen Display tips of the Home screen tips operation.
Adding a folder to the Home screen Changing Kisekae 1 In "Add to home screen" menu, tap [Folder]. 1 In "Add to home screen" menu, tap [Kisekae]. 2 Select a folder you want to add. 2 Select Kisekae you want to change to and tap [Set]. ･ The folder appears on the Home screen. ･ You can rename or add items to a folder by selecting [New folder] on the folder selection screen.
･ When you tap [Live wallpapers], select a content, tap [Set wallpaper]. You can also download and add Live wallpaper content from a web page. For some contents, you can change type or contents displayed on the wallpaper by tapping [Settings]. ･ When you tap [Wallpaper gallery], select an image you want to use as wallpaper, then tap [Set wallpaper]. ❖Information ･ Alternatively, from the Home screen, tap t and Adding a home screen 1 From the Home screen, tap t and tap [Home screens].
Moving an icon on the Home screen 1 2 3 From the Home screen, touch an icon you want to move. Learning Applications screen 1 From the Home screen, tap ･ Drag it anywhere. ･ The Applications screen appears. a To move to another Home screen, keep touching the icon and drag to left or right. . d b c Release your finger from the icon. Deleting an icon from the Home screen 1 From the Home screen, touch an icon you want to delete. 2 Tap [Delete].
Applications The applications displayed on the Applications screen by default are as follows. ･ For usage of some applications, separate subscription (Charged) is required. ■ DOCOMO Services Icon Applications dmenu dmarket i チャネル (i-Channel) Machi-chara docomo backup ■ Description A shortcut application for "dmenu" to find contents that you used in i-mode and joyful and convenient contents for smartphones readily. Activate dmarket. You can buy contents such as music, videos, books at the dmarket.
Icon ■ Applications 声の宅配便 (Koe-noTakuhaibin) Description Use "Koe-no-Takuhaibin" easily and conveniently on the smartphone. You can record and play voice messages with a simple operation. Send/receive mails using docomo mail address (@docomo.ne.jp). sp モードメール (spmode mail) You can use pictogram and Deco-mail. Mails can be received automatically. Email Send and receive emails (multiple accounts are also available). Gmail Send and receive mails from/to a Google account.
Icon Applications Videos YouTube G ガイド番組表 (G-Guide program table) 1Seg Music player FM radio Connected devices Facebook Google+ Messenger Timescape™ Gallery ■ Description An application for accessing movie rental service of Android market. Select a movie you want to watch and rent it. Playback videos around the world or upload recorded videos. View ground-based broadcasting, BS digital broadcasting.
Icon Applications Navigation Description Display Google map navigation to receive detailed guides for your destination. Use various information registered on Google map, such as shops around the current location. Check and share the location information of specified friends. Create original name card to display in the My profile field of docomo "Phonebook" application. An application which allows you to send and receive phonebook data, etc. via infrared communication.
Icon Applications docomo location information Update center Flash Player Settings Description Provide location information such as imadoco search, imadocokantan search, Keitai-Osagashi Service, Emergency Location Report. Also access service website to change or make various settings. Update the latest software or application. Change settings for controlling application running method in Flash Player. Page − P.252 − ❖Information ･ Some application names may not be displayed fully.
Changing the Applications screen From the Applications screen, you can add icons, sort icons, uninstall applications. Also you can change group setting. Adding an application icon to the Home screen 1 2 From the Applications screen, touch and hold an icon you want to add to the Home screen. Tap [Add]. ･ The application icon is added onto the Home screen. ❖Information ･ From the Home screen, tap t and [Add]u[Shortcut]uTap [Application] and select an application to add.
Adding a shortcut of group to the Home screen 1 2 From the Applications screen, touch and hold a group you want to add to the Home screen. Tap [Add]. ･ Shortcuts to the group is added to the Home screen. ❖Information ･ From the Home screen, tap t and [Add]uTap 2 1 2 From the Applications screen, touch and hold a group you want to change the color. Tap [Edit label] and select label color to change. ･ The color for group name is changed.
Sorting groups 1 From the Applications screen, touch and hold an group name you want to sort. 2 Drag it to the place you want to move and lift up your finger. ･ Searching applications Search application installed into the terminal to activate. 1 ･ For the first time to join Latitude, a message confirming whether to agree to Google's privacy policy appears. Select [Agree] or [Disagree]. ･ The software keyboard appears. The group is moved.
Switching application screens Icons on the Applications screen can be displayed in a list or tiles. 1 From the Applications screen, tap t and then tap [List format]/ [Tile format]. Home application information You can check information on the home application and make display setting. 2 Tap [Home settings]. ･ The "Home settings" screen appears and the following setting can be made. Personal area Set whether to display personal area on the Home screen.
Calling/Network Services Making/Receiving a call Making a call 1 From the Home screen, tap [Phone]u[Dial]. 2 Enter the number of the recipient and tap . ･ If a wrong number is entered, tap to delete the number. ❖Information ･ To activate Xperia™ phone application, from the Home screen, tap , then tap [Dial]. Entering pause (,) This function allows you to operate voice mail at home, to reserve tickets, or to check the balance of a bank account, etc. 1 From the Home screen, tap [Phone]u[Dial].
･ When calling 110, 119 or 118 for emergency from the terminal, tell that you are calling from a mobile phone, and give your phone number and your current location precisely for checking callback from the police/fire department. Also, make a point to call in a stationary position to prevent the call from being dropped. Do not power off the terminal for at least 10 minutes after the emergency call just in case the Police or Fire/Ambulance may have to get in contact with you.
Declining a call 1 While receiving a call, touch (right) and drag it to (left). ■ 1 Making a call Make a call with Stereo Headset with Microphone (Sample) connected. ･ ❖Information ･ Even during the screen lock or key lock, the icon appears and you can decline a call by the same operation. Using Stereo Headset with Microphone An operation of making a call is the same as usual operation. (P.81) 2 Press the switch to end the call.
Adjusting the ear speaker volume 1 Operations during a call ■ During a call, press m to adjust. Calling screen a ❖Information f b ･ You can adjust the ear speaker volume only during a call. c d e Muting the ringtone for an incoming call 1 When receiving a call, press m. ❖Information ･ Alternatively, press p to mute the ringtone for incoming call. ･ From the Home screen, press m to mute the ringtone for an incoming call.
❖Information ･ During a call/on hold, tap t to display "Hold"/ "Retrieve call". ･ To set a call on hold, "Call waiting" subscription is required. (P.101) Recent calls screen On the Recent calls screen, incoming call history and outgoing call history are displayed in chronological order. ❖Note ･ Do not bring the terminal close to your ear with the speakerphone on to avoid from hearing damage. Call history Showing call history 1 From the Home screen, tap [Phone]u[Recent calls].
･ Number in bracket indicates number of combined history. e Outgoing history f Outgoing g History icons Adding a number from the call history to Phonebook 1 : Missed call : Incoming call : Outgoing call h Date On the Recent calls screen (P.85), touch and hold a phone number and then tap [Add to phonebook]. ･ ❖Information ･ On the Recent calls screen, tap t and tap [Search location] to check the current location of the party using imadocokantan search. 2 When you have missed calls, the status bar.
❖Information ･ On the Recent calls screen, touch and hold a log you want to delete, tap [Remove from call log]u[OK] to delete an item. Phonebook In the Phonebook, you can enter various information for contacts, for example, phone numbers, mail addresses and web service accounts. You can display phonebook entry to get quick access to that contact. Phonebook list screen On the phonebok list screen, you can view details of your contacts.
Make a call to saved phone number. Create and send message (SMS). Select Email application to create and send an email. ･ If [Use by default for this action.] checkbox is marked, application selection screen will not appear for the next time. Managing phonebook Adding a new phonebook entry 1 On the phonebook list screen (P.87), tap [Register]. 2 Tap [Phone contacts]/[docomo]. 3 4 ･ Enter a name. Select or enter desired additional information for the contact. ･ 5 When you set Google account etc.
Changing display conditions for phonebook entries 2 Tap [Edit]. 3 Edit the desired information and tap [Save]. ･ You can set registered phonebook entries to be displayed in the phonebook list. 1 On the phonebook list screen (P.87), tap t, then tap [Others]u[Display settings]. ■ Setting display condition Mark [Only contacts with phones]. ･ Only phonebook entries with phone numbers registered are displayed.
Deleting a phonebook entry 1 On the phonebook list screen (P.87), tap t, then tap [Delete]. 2 Mark the phonebook entry you want to delete. ･ 3 If you want to delete all phonebook entries, tap [Select all]. Tap [Delete]u[OK]. Checking My profile and editing information 1 On the phonebook list screen (P.87), tap [My profile]. 2 Tap [Edit]. 3 Enter the new information or make the changes you want. By tapping [Add] on the profile editing screen, you can add information to enter.
Sending phonebook via infrared communication/Bluetooth/Email/ Gmail Registered phonebook and My profile information can be sent using infrared communication (P.163), Bluetooth function (P.166), or email attachment function. ■ 1 Sending phonebook Tap a phonebook entry you want to send on the phonebook list screen (P.87). ･ The profile screen of the phonebook appears. Tap t and [Share]. Select sending method and follow the onscreen instructions.
･ From the Home screen, tap [Phone]u[Favorites] to display the phonebook data registered in Favorites and "Commonly used phonebook data". Touch and hold the phonebook data registered in Favorites or Commonly used phonebook data to select "Remove from favorites"/"Add to favorites". Setting photo in a phonebook entry 1 On the phonebook list screen (P.87), tap a phonebook entry you want to add a picture. ･ 2 3 4 5 6 The profile screen of the phonebook appears.
4 Select [Yes]/[No] to attach name card. 5 Tap [OK]. Importing phonebook from microSD card 1 2 3 4 On the phonebook list screen (P.87), tap t, then tap [Others]u[Import/Export]. Tap [Import from SD card]. Tap [Phone contacts]/[docomo]. ･ When you set Google account etc., it appears as an import destination. Select vCard file you want to import. ･ If there is only one file, vCard file selection screen does not appear. The file is imported immediately.
･ Alternatively, on the phonebook list screen, tap [My profile] tab, then tap t and [General settings]u[Data management]u[Import]u[Import from SIM card] to import contacts from the UIM. ･ To export phonebook entries to UIM, use Xperia™ phonebook application. Note that only name and the first phone number can be saved because of memory space of UIM. For some phonebook entries, a part of data may not be exported. Sharing phonebook entry currently displayed 1 2 3 On the phonebook list screen (P.
Importing phonebook from microSD card 1 Attach the microSD card with phonebook entries saved to the terminal. 2 On the " インポート (Import)" tab screen, tap a file you want to import. 3 Tap [ 上書き (Overwrite)]/[ 追加 (Add)]. ･ Imported phonebook data is saved in docomo account. Exporting phonebook to microSD card 1 Attach the microSD card to the terminal. 2 On the " エクスポート (Export)" tab screen, tap [ 開始 (Start)]. ･ The Phonebook data saved in docomo account is saved onto the microSD card.
Network Services Available Network Services You can use the following DOCOMO network services on the terminal. For details on the outline and how to use each service, see the relevant pages indicated in the following table. ･ You cannot use the network services when you are outside of the service area or in a location without the radio wave. ･ "Stop of service" does not mean canceling the subscription such as Voice Mail service, Call Forwarding Service, etc.
Voice Mail service The Voice Mail Service takes messages for you, as long as it answers a call with the answering message, if there is an incoming call when you are in a location without the radio wave, while the terminal is powered off, or when you cannot answer a call within the preset ring time. ･ When the Voice Mail service is set to "Activate" and if you do not answer an incoming voice call, the call is saved in "Recent calls" as a "Missed call" and (Missed call) appears in the status bar.
Setting Voice Mail Service 1 From the Home screen, tap t and tap [Settings]. 2 Tap [Call settings]u[Network service setting]. 3 Tap [Voicemail]. ･ Notification settings Activate Missed Call Notif. Select items you want to use. Activate Voicemail Tap [OK] to activate the Voice Mail Service. Set ring time Enter the ring time (0 to 120 seconds). It changes only the ring time. If the ring time is set to 0 seconds, an incoming call is not saved in "Recent calls".
Playing the voice message 1 When the SMS notification "NTT DoCoMo VM:XX" appears, tap [New message] from the Notification panel (P.43). ･ 2 Basic flow of the Call Forwarding Service Save the forwarding number ▼ A recorded message plays. Follow the voice prompts to operate.
❖Information ･ Even when the Call Forwarding Service is set to "Activate Call Forwarding", you can answer the call during a ringtone sounds. Setting Call Forwarding Service 1 From the Home screen, tap t and tap [Settings]. 2 Tap [Call settings]u[Network service setting]. 3 Tap [Call Forwarding]. ･ Select items you want to use. Activate Call Enter the forwarding phone number Forwarding and ring time, then tap [OK] to activate the Call Forwarding Service.
Putting the current call on hold and answering an incoming call Call Waiting When there is another incoming call while you are on a call, the in-call ringtone notifies you of the second call. You can answer the second call by putting the first call on hold. You can also put your current call on hold and place a call to another party. 1 When you hear the beep during a call, tap [Answer]. ･ ❖Information ･ Even when the call is on hold, the caller is charged for a call fee.
Putting the current call on hold and making a call to another party 1 During a call, tap (Dialpad). 2 Enter the other party's phone number, then tap . ･ 3 (Phonebook)/ The first call is automatically on hold and switched to the new call you made. You can also search for a party by tapping (Phonebook). Switch to the first call. ･ To terminate the new call, tap [End call]. The new call is terminated and switched to the first call. ･ To put the new call on hold, tap [Switch to this call].
Nuisance Call Blocking service You can register "crank call" such as prank call not to be received. When call rejection is registered, follow-on incoming calls are automatically rejected. Guidance responds to the caller. And, you can register, check, delete phone numbers to be rejected connecting Nuisance Call Blocking service setting site. ･ Even if there is an incoming call from the phone number with rejection registered, ringtone does not sound. And the call is not recorded in the call log.
2 Tap [Call settings]u[Network service setting]. 2 Tap [Call settings]u[Network service setting]. 3 Tap [Caller ID request service]. 3 Tap [Second call settings]. ･ Select items you want to use. Activate caller ID request Deactivate caller ID request Check settings Tap [OK] to activate Caller ID Display Request Service. Tap [OK] to deactivate Caller ID Display Request Service. Check the current service settings.
声の宅配便 (Koe-no-Takuhaibin) Koe-no-Takuhaibin is a service of taking voice messages for you. ･ The message can be recorded up to 15 minutes for 1 message, up to 500 messages, and stored for 720 hours. And up to 5 messages can be protected. (Unprotected messages will be erased after 720 hours automatically.) ･ It is unavailable from overseas. ･ Koe-no-Takuhaibin is a service requiring no subscription/monthly charge. But for recording and playing a message, a call charge is applied.
Recording a message You can record a message by making a call with Koe-no-Takuhaibin. 1 2 From the Home screen, tap [Phone]u[Dial] tab. Enter a phone number and tap [Koe-no-Takuhaibin]. ･ 2 Tap [ 設定 (Setting)]. ･ Select items you want to use. 設定確認・変更（サイト接続） Connect website to (Check/change settings (connecting website)) check/change settings. 設定確認・変更（音声発信） Make a call to check/ change settings. (Check/change settings (voice prompt)) Operate the following voice prompts.
Settings Viewing the setting menu From the Home screen, tap t. Tap [Settings]. ■ Setting menu 1 2 docomo service Xperia™ Wireless & networks Call settings Sound Display Location & security Applications Accounts & sync Privacy Storage Language & keyboard Voice input & output Accessibility Date & time About phone P.107 P.108 P.109 P.119 P.119 P.122 P.124 P.129 P.132 P.135 P.136 P.138 P.138 P.139 P.139 P.
Xperia™ You can back up/restore data or files in the terminal or set preferred applications. You can also set synchronization function for Facebook in the terminal, make settings for USB connection or Wi-Fi connection to a PC or other devices. Backup & restore Battery life Connectivity Facebook inside Xperia™ Preferred apps settings P.108 View built-in battery performance. P.158 P.
Restoring the back up file to the terminal You can restore data or files previously backed up to the microSD card. 1 From the Settings screen (P.107), tap [Xperia™]u[Backup & restore]. 2 Tap [Restore]. ■ Contacts/Call log/Message (SMS)/ Bookmark Tap [Restore data now]u[OK]u[OK]. ･ The back up data in the microSD card is restored to the terminal. If the restoring data already exists in the terminal, the back up data cannot be added.
❖Information ･ If you have several available connections, a marked radio button to the right indicates the active network connection. ･ Note that, when using the prediction conversion by one-byte alphabet entry mode (English mode) with mark in [Auto space] checkbox on Japanese keyboard settings screen (P.62), spaces may be entered automatically. In this case, delete spaces. Setting an access point additionally 1 2 3 4 5 From the Settings screen (P.
mopera U mopera U is ISP of NTT DOCOMO's Internet connection. If you have subscribed to mopera U, you can use Internet after making the simple settings. mopera U is a service requiring subscription. Setting mopera U 1 From the Settings screen (P.107), tap [Wireless & networks]u[Mobile networks]u[Access Point Names]. 2 Mark [mopera U ( スマートフォン定 額 ) (mopera U (Smartphone flatrate))]/[mopera U 設定 (mopera U settings)] radio button. ･ Return to the Home screen and open the Browser.
About Wi-Fi ■ Reception interference caused by Bluetooth devices Bluetooth devices and wireless LAN (IEEE802.11b/g/n) devices use the same frequency band (2.4GHz). If you use Bluetooth devices near a wireless LAN device, reception interference may occur or the communications speed may lower. Also, you may hear noise or have a connection problem. Communication may be interrupted or sound may be lost while streaming data, etc.
Connecting to a Wi-Fi network 1 Available Wi-Fi networks are displayed under "Wi-Fi networks". The available networks may be open or secured. This is indicated by or next to the WiFi network name. appears next to the name of the Wi-Fi network that can be connected with WPS functions. Select Wi-Fi network you want to connect, tap [Connect]. ･ If you are trying to connect to a protected Wi-Fi network, you are asked to enter the security key for that Wi-Fi network before you can connect to it.
Setting the Wi-Fi network notification to ON 1 2 Confirm Wi-Fi is ON and from the Settings screen (P.107), tap [Wireless & networks]u[Wi-Fi settings]. Mark [Network notification] checkbox. Scanning for Wi-Fi networks manually 1 From the Settings screen (P.107), tap [Wireless & networks]u[Wi-Fi settings]. 2 3 Tap t. Tap [Scan]. 4 Tap a Wi-Fi network in the list to connect to it. ･ Scanning for Wi-Fi networks is started, and they are displayed under "Wi-Fi networks".
3 Enter [Network SSID] name of the Wi-Fi network you want to add. 4 By changing Wi-Fi sleep policy, you can Tap [Security] field, then mark a choose to disable the Wi-Fi function in the radio button of security type for the Wi-Fi network you want to add. terminal when the screen backlight turns off. ･ 5 6 4 options, "Open", "WEP", "WPA/WPA2 PSK", or "802.1x EAP", appear. If required, enter security information for the Wi-Fi network you want to add. Tap [Save].
Using a static IP address You can set up the terminal to connect to a Wi-Fi network using a static IP address. Setting up a static IP address 1 From the Settings screen (P.107), tap [Wireless & networks]u[Wi-Fi settings]. 2 3 4 Tap t. 5 Tap an item to enter necessary information. Tap [Advanced]. Mark [Use static IP] checkbox. ･ ･ 6 7 Item of IP settings can be selected. Enter "IP address", "Gateway", "Netmask", "DNS 1" to use a static IP address. Tap t. Tap [Save].
4 5 Tap [USB tethering]. Confirm details of the cautions displayed, tap [OK]. ･ [USB tethering] is marked. ❖Information ･ System requirements (OS) for USB tethering are as follows. A required driver is automatically installed. - Microsoft Windows 7 - Microsoft Windows Vista - Microsoft Windows XP 6 Enter security information of the Wi-Fi hotspot to set as required. 7 Tap [Save]. ❖Information ･ By default, the password is set at random. You can change the password as desired.
Connecting to a VPN (Virtual Private Network) Virtual Private Network (VPN) is a technology to connect to the information in a protected local network from another network. Generally, VPNs are provided to companies, schools and other facilities. A user can access to the information in the local network from outside of the premises. To set up a VPN access from the terminal, you need to retrieve the information related to security from your network administrator. For details, refer to http://www.sonymobile.
Disconnecting a VPN 1 Open the Notification panel, and tap the VPN connecting notification. ･ Tap a connecting VPN to disconnect. Sound Set ringtones, operation sound, vibrator, etc. xLOUD™ Call settings You can use the network services and search for available networks. Network service P.96 setting Service When you start using overseas or providers move out of your operator's network, the terminal searches another available network and reconnects to it.
Setting Silent mode 1 Press and hold p for over a second. ･ 2 Adjusting each sound volume 1 From the Settings screen (P.107), tap [Sound]u[Volume]. ･ Phone options menu appears. Tap [Silent mode]. ❖Information ･ Alternatively, from the Settings screen (P.107), tap [Sound] and mark [Silent mode], or from the key unlocking screen (P.39), touch and drag to the left to set silent mode. ･ Setting the phone to silent mode does not mute sounds for playback of video or music, alarm, etc.
Adjusting the ringtone volume with the volume key 1 From the Home screen, press up or down of m. ･ The volume adjustment bar appears, you can adjust the volume up or down. ❖Information ･ You can also press m or p to mute the ringtone for an incoming call. Selecting a notification ringtone 1 From the Settings screen (P.107), tap [Sound]u[Notification ringtone]. 2 Select a ringtone and tap [Done].
Display Set brightness, orientation of the screen, etc. Mobile BRAVIA Engine To view photos or movies colorfully and beautifully, set image quality improving procedure (Mobile BRAVIA Engine). It adjusts contrast, color shade, etc.* Brightness P.122 Auto-rotate screen P.122 Animation P.122 Screen timeout P.123 Theme Set the background image for the Home screen or Settings screen. Lock screen settings P.123 * Setting Mobile BRAVIA Engine improves image quality when using Xperia™ application.
Adjusting the idle time before the screen turns off 1 From the Settings screen (P.107), tap [Display]u[Screen timeout]. 2 Select a time option before the screen back light turns off. ❖Information ･ To turn the screen back light off immediately, press p. Setting information displayed on the key unlock screen Yon can set information displayed on the key unlock screen (P.39). 1 From the Settings screen (P.107), tap [Display]u[Lock screen settings].
･ Flick right around date and time displayed on the key unlock screen to display a shortcut for the preset application, or flick left to display Music player widget. You can activate the application or play music without unlocking key lock. You cannot replace the Music player widget. ■ Changing wallpaper Tap [Wallpaper]u[Gallery]/[Xperia™ wallpapers]. ･ For setting procedure, see Step 2 (P.69) in "Changing wallpaper". ■ Displaying Machi-chara Mark [Machi-chara] checkbox.
*2 Set the password to the credential storage in advance. *3 Save certificates and credential information in the credential storage. Protecting the UIM Some functions provided for convenient use of the terminal require the security code to use them. Besides the security code for locking the terminal, the network security code necessary for the network services etc. are available. Make use of the terminal using an appropriate security code according to the purpose.
PIN code You can set a security code called PIN code to the UIM. The code is set to "0000" at the time of subscription. It can be changed by yourself. PIN code is a 4- to 8-digit number (code) that must be entered for user confirmation to prevent unauthorized use by a third party every time you insert the UIM into the terminal or when the terminal is powered on. Entering the PIN code enables making/ receiving calls and terminal operation.
Changing the PIN code ･ You can change the PIN code only when the UIM PIN is enabled. 1 From the Settings screen (P.107), tap [Location & security]u[Set up SIM card lock]u[Change SIM PIN]. 2 Enter the current PIN code of the UIM and tap [OK]. 3 4 Enter a new PIN code of the UIM and tap [OK]. Enter the new PIN code of the UIM again and tap [OK]. Unblocking the locked UIM 1 2 3 On the PUK code entry screen, enter the PUK code and tap [OK]. Enter the new PIN code of the UIM and tap [OK].
･ When you tap [Password], follow the onscreen instructions to enter 4 or more characters including alphabets. 2 ･ Changing screen unlock method 1 From the Settings screen (P.107), tap [Location & security]u[Change screen lock]. ･ Enter current screen unlock pattern, PIN or password. ･ If you should fail 5 times when you enter the unlock pattern, wait 30 seconds and then try again. 2 Tap [Pattern]/[PIN]/[Password]. ･ Select items you want to change into. For setting procedure, see Step 2 (P.
- Mark [Enter Google account details], tap [Next], and enter Google account and password, then tap [Unlock] to unlock the screen lock. ･ When setting new unlock pattern after unlocking screen lock, "Screen unlocked" appears. Tap [Yes] to reset unlock pattern. ❖Information ･ Tap [Try again] to retry entering pattern in 30 seconds. ･ Alternatively, tap [Try again] and [Forgot pattern?] to display answering question screen that you set the unlock pattern. ･ You can set multiple Google accounts.
3 Read the cautions displayed, tap [OK]. ･ [Unknown sources] checkbox is marked. Checking downloaded applications You can check data downloaded from websites, such as unknown source's applications, in the following steps. 1 2 From the Home screen, tap [Browser]. Tap t and tap [More]u[Downloads]. ❖Information ･ Applications downloaded from Android Market do 1 2 3 Manage and delete installed applications, display memory usage condition, etc. or change the settings.
Deleting all data of the application ･ Before deleting all installed application data, back up contents related to the application that you want to save including data saved in the application. 1 2 3 4 From the Settings screen (P.107), tap [Applications]u[Manage applications]. Tap an application to delete the data. Read the cautions displayed, tap [OK]. ･ Before deleting installed application, back up contents related to the application that you want to save including data saved in the application.
Keeping the screen backlight ON while charging 1 2 From the Settings screen (P.107), tap [Applications]u [Development]. Mark [Stay awake] checkbox. Accounts & sync You can manage (add or delete) online service accounts or synchronize contacts, messages, etc. saved in online services with the terminal. Background data traffic All the applications installed to the terminal perform automatic data communications. Activate auto-sync P.135 Manage accounts P.
･ If you set a Google account, you can tap your Google account displayed on the "Accounts & sync" screen in the setting menu to manually synchronize data from the following items. Sync Instant Upload* Synchronize photos taken with the camera or screen shots or photos in a microSD card with photos in Google+. Sync Contacts Synchronize contacts stored in Gmail with the phonebook stored in the terminal. Sync Gmail Synchronize Mail logs used in Gmail account with Gmail on the terminal.
❖Information ･ Set Facebook account to display in the status bar. Drag the status bar downwards, tap [Facebook inside Xperia™], mark the [Facebook integration] checkbox, read the displayed note, and then tap [Accept]. Tap (Facebook inside Xperia™) added to the "Accounts & sync settings" screen, and tap the following items to synchronize and display corresponding data. Sync Calendar Synchronize events such as Friends' birthdays, etc., stored in Facebook with Calendar in the terminal.
Setting Auto-sync 1 From the Settings screen (P.107), tap [Accounts & sync]. 2 Mark [Background data traffic] checkbox. 3 4 Tap [Activate auto-sync]. Read the cautions displayed, tap [OK]. ･ [Activate auto-sync] checkbox is marked. 5 Tap an online service whose account is set. 6 Tap to mark an item for automatic synchronization. ･ If the items to be synchronized are marked and checkboxes are led by , synchronization starts.
1 From the Settings screen (P.107), tap [Privacy]u[Factory data reset]u[Reset phone]. ･ Mark [Erase internal storage] checkbox to delete all contents (music, photos, videos, etc.) on the internal storage. ･ Enter your screen unlock method as required. 2 Tap [Erase everything]. ･ By tapping [Erase everything], the terminal restarts automatically. ❖Information ･ If you reset the terminal, license information for the DRM protected content may be erased making the content unable to be played.
❖Information ･ Note that when available memory of internal storage becomes 32KB or less, microSD card cannot be mounted. ❖Information ･ Formatting USB storage (external memory such as microSD card) deletes all the data in it. Managing memory Formatting the internal storage of the terminal Formatting microSD card 1 From the Settings screen (P.107), tap [Storage]u[Clear internal storage]. 2 3 Tap [Clear internal storage]. 1 2 3 From the Settings screen (P.107), tap [Storage]u[Unmount SD card].
Increasing the available memory of the terminal If the terminal has a small memory, you can perform the following operations to increase available memory: ･ In the browser, you can clear all temporary Internet files and browser history information. For details, refer to "Clearing history" (P.157). ･ Uninstall programs that you no longer use. For details, refer to "Deleting installed application" (P.131). Language & keyboard You can select language and keyboard input.
Language Pico TTS* Set language for reading out text. Make settings for installed voice synthesis engine. * Japanese is not supported. Accessibility You can set call end operation and user support service which sounds or vibrates according to user's operation. ❖Information ･ A user support application is not installed by default. For the first time of use, install a screen reader for the terminal from the Android Market according the onscreen instructions.
Setting the time zone 1 2 From the Settings screen (P.107), tap [Date & time]u[Select time zone]. Select time zone you want to set. Setting the time 1 From the Settings screen (P.107), tap [Date & time]u[Set time]. 2 Tap number to adjust the hour and minute. ･ 3 When you unmark [Use 24-hour format], you can change AM/PM. When you tap [am], it changes to [pm] (or vice versa). Tap [Set]. Setting the time format 1 From the Settings screen (P.
Mail/Internet sp-mode mail Send/receive mails using i-mode mail address (@docomo.ne.jp). You can use pictogram and Deco-mail. Mails can be received automatically. For details on sp-mode mail, refer to " ご利用ガイドブック (sp モード編 ) (Mobile Phone User's Guide [spmode])" (in Japanese only). 1 From the Home screen, tap [sp モー ドメール (sp-mode mail)]. 2 Scroll the screen, then tap [ ダウン ロード (Download)]. ･ After this step, follow the instructions on the screen.
5 Tap "Write message" field and enter a message. ･ 6 ❖Information ･ When you receive a message (SMS), When the number of entered characters comes close to a limit, a counter appears on the upper left of the text box and you can check the remaining entry space. Tap [Send]. ❖Information ･ For the character entry, see "Character entry" (P.47). ･ You can also send/receive text messages to/from customers of overseas network operators.
Setting message (SMS) 1 From the Home screen, tap then tap [Messaging]. 2 Tap t and [Settings]. ･ Deleting a message , You can set the following options. Delivery report Mark to mark a message thread you sent each time a recipient receives the message. Notifications Mark if you want to receive a notification in the status bar when a new message arrives. Notification Set if you want to receive a tone notification in selected ringtone when a new message arrives.
･ Email You can create an email account provided by mopera U mail, a POP3 or IMAP compatible email account provided by general ISP (provider), or an Exchange ActiveSync account to send or receive email. Making initial setting for Email Email setup wizard appears. Set according the onscreen instructions. Multiple email accounts can be set. 1 From the Home screen, tap and then tap [Email]. 2 Enter your email address and password. Tap [Next].
･ 4 5 6 To enter multiple email addresses directly, separate with a comma (,) and then enter the next email address. Enter a subject. Enter a message text. To attach a file, tap . ･ Attach a file in the following operations. Add Select a file from the saved image file list. picture Take photo Start the camera to take a photo and attach it. Add video Select a file from the saved video file list. Record Start the camera to record a video and video attach it.
･ If you set "Inbox check frequency" in Account settings (P.148) to an item other than "Manual", and if you are using the pay-as-you-go data communication, you may be charged every time you check your email. ･ If you tap the address of a received email, you can register it in Contacts. If it has been already registered, you can display the details of the contact. ･ Tap (gray) to turn (yellow) on the mail message screen to add the marked mail to "Starred" on the email screen.
Replying/forwarding email 1 From the Home screen, tap and then tap [Email]. ･ Deleting email , 1 ･ When the Email screen appears, tap and select an email account whose email you want to reply or forward from an account list. ■ Replying Tap an emailuTap (Reply) or (Reply all)uEnter the text and tap (Reply). ■ Forwarding Tap an emailuTap (Reply)uEnter the email address of recipientuEnter the text and tap (Reply).
Outgoing settings Changing Email account settings 1 From the Home screen, tap and then tap [Email]. ･ 2 , When the Email screen appears, touch and hold an account that you want to change the settings from an account list and tap [Account settings] to change the settings. Tap t, then tap [More]u[Account settings]. ･ You can set the following options. Account name Your name Signature Inbox check frequency Change account name. Change your name (sender name). Change your signature.
5 Enter an account name and name you want to display on outgoing messages. ･ If "What type of account is this?" appears, tap an email account type and follow the onscreen instructions to set. ･ If you set an Exchange ActiveSync account, a name displayed for sent mail cannot be set. 6 ･ ･ ･ ･ your email service provider or system administrator for the correct email account settings.
2 Enter mopera U mail address and mopera U password, then tap [Manual setup]/[Next]. ･ If you tap [Next], it changes automatically to POP3 account. Go to Step 4. 3 Tap [POP3] from the type of the mail account. 4 Check that you have entered [User name] and [Password] for mopera U correctly, and [mail.mopera.net] for the POP3 server. ･ If you tap [Next] in Step 2, "mail.mopera.net" is entered in the SMTP server field. 5 Select the security type.
Using Gmail Google Talk If you have a Google account, you can send/ receive emails by using Gmail on your terminal. If you have no Google account, see "Setting Google account" (P.132). ❖Information ･ Gmail messages are not displayed in Timescape. Refreshing Gmail From the Home screen, tap then tap [Gmail]. 2 On the Inbox, tap t and tap [Refresh]. , Synchronizing Gmail application in the terminal with your Gmail account starts, and the Inbox is refreshed.
Early Warning "AreaMail" Early warning "Area mail" is a service with which you can receive earthquake early warning, etc. delivered by the Meteorological Agency. ･ Area Mail is a free service for which subscription is not required. ･ Area Mail cannot be received in the following case.
Setting Early Warning "AreaMail" 1 2 From the Home screen, tap then tap [Area Mail]. Using Browser , Tap t and [Settings]. Receive setting Beep tone Opening Browser 1 From the Home screen, tap [Browser]. Set whether to receive Area Mails. Set sounding time for Area Mail reception and whether to sound a dedicated ringtone even in silent mode. Check screen Check the ringtone and screen for reception of earthquake early warning image and or Area Mail for disaster/evacuation beep tone information.
Exiting Browser 1 Tap y. ･ All open windows are closed and Browser ends. Displaying web page Browser offers advanced features that let you view web pages like on a PC. Opening a new browser window You can open up to 8 browser windows. 1 While viewing a web page, tap t and tap [New window]. ･ A new browser window opens in the default home page. Closing browser window 1 On the Browser screen, tap t and tap [Windows]. 2 Tap on the browser window you want to close.
2 Enter the search item. ･ As you enter, matching characters are highlighted in green. Back to the previous matched item Go to next matched item 3 Tap to close the search bar. Copying text in a web page 1 2 While viewing a web page, tap t and tap [More]u[Select text]. Place your finger at the start of the text you want to copy and then drag to the end of the text you want to copy. ･ 3 ･ On some web pages, selecting characters may not be available.
Operating links Operating links in web pages 1 2 Open the web page you want to operate the links. Managing bookmarks and history You can check history and store many bookmarks on the terminal. To open the web page, tap the link. Bookmarking a web page ･ The links get enclosed in an orange box the Browser screen, go to the 1 On when selected. web page you want to bookmark.
･ Tap [Most visited]/[History] tab in the bookmark list screen and tap on the right side of the record. turns into and the web page is added to the bookmark list. Checking browsing history 1 Opening a bookmark 1 On the Browser screen, tap t and [Bookmarks]. 2 Tap the bookmark you want to open.
File management Handling a file Files in the terminal should be operated on the file handling application. For example, to delete files saved in a microSD card, use the deletion function of the applications such as Music player or Gallery. With "Share" function of each application, you can exchange files via Infrared communication, Bluetooth or by email file attachment sending to/receiving from other compatible devices.
･ 2 The terminal is connected by "Media transfer mode (MTP)" and "Mass storage mode (MSC)", which are USB connection modes set by default, and 2 screens "Xperia acro HD SO-04D" and " リムーバブル ディスク (Removal disk)" appear on the PC. "Media transfer mode (MTP)" allows you to access the internal storage and "Mass storage mode (MSC)" allows you to access the microSD card inserted into the terminal. Tap [Skip].
･ When the terminal is connected to a PC, charging starts automatically. Disconnecting the microUSB cable safely ･ Do not disconnect the microUSB cable during data transferring. Otherwise, data may be damaged. ･ If you connect the terminal in the Media transfer mode (MTP) only, make sure that data transfer is not in progress and just disconnect the microUSB cable. 1 2 3 4 Drag the status bar downwards. ･ When "Connect your phone" is displayed, go to Step 4.
Connecting the terminal to a PC on a Wi-Fi network If the terminal and a PC* are connected in a pair on a Wi-Fi network, automatic connection/disconnection of internal storage of the terminal or a microSD card with a PC is enabled when the terminal user comes in and out of the Wi-Fi area. You can easily access to files in the internal storage of the terminal or a microSD card from a connected PC. * Use Microsoft Windows 7 to make a pair setting.
❖Information ･ From the Home screen, tap t, then tap [Settings]u[Xperia™]u[Connectivity] to display "Host name" (PC name) in the "Trusted devices" field. To cancel connection setting, tap the host name and [Forget]. Until "Forget" is tapped, the connection setting retains even if you connect/disconnect repeatedly by coming in and out of a Wi-Fi area. ･ If the privacy separator function for Wi-Fi network (access point) is enabled, pair setting cannot be made.
Transferring data using Media Go 1 Connect the terminal to a PC using a microUSB cable. ･ 2 When "PC Companion software" screen appears on the terminal, tap [Skip]. ･ Infrared communication may not be performed in areas exposed to direct sunlight, directly under fluorescent lights or near infrared devices. ･ Depending on the terminal of the other party, it may be difficult to exchange data. Select Media Go from the PC's start menu and activate Media Go.
･ If the terminal receives a call during infrared ･ ･ ･ ･ ･ ･ ･ * communication, data exchange is interrupted and the incoming call screen appears. If the set alarm time comes during infrared communication, data exchange is interrupted and the alarm starts to sound. is displayed in the status bar during infrared communication. Up to 2MB of data of contacts*, Myself*, photos, videos and music can be sent and received.
■ 1 Sending data from an application menu From the application menu, tap [Share]u[Infrared]. ･ To send 1 phonebook entry, from the Home screen, tap u[Phonebook] u[(a phonebook entry to send)]ut and tap [Share]u[Infrared]. ･ To send all phonebook entries, from the Home screen, tap u[Phonebook]ut and tap [Others]u[Import/Export]u[Share phonebook data]u[Infrared], then enter the same authentication passcode as that of the recipient and tap [OK].
･ Within 10 meters, turn off either the Bluetooth device or the wireless LAN device. * The terminal does not communicate wirelessly with all types of Bluetooth devices. Bluetooth DUN is not supported. Using Bluetooth function The Bluetooth function creates a wireless connection to other Bluetooth devices, for example, handsfree devices. A range within 10 meters, with no solid objects in between, is recommended. You must turn on the Bluetooth function to communicate with Bluetooth devices.
Entering the terminal's name You can name the terminal. The name appears on Bluetooth devices when you use the Bluetooth function. 1 Make sure that the Bluetooth function is on. 2 3 From the Home screen, tap t. Tap [Settings]u[Wireless & networks]u[Bluetooth settings]u[Device name]. 4 5 Enter a name. Tap [OK]. Making pair setting for the terminal and Bluetooth device By making pair setting for the terminal and another Bluetooth device, you can use the device such as Bluetooth handsfree headset etc.
1 2 From the Home screen, tap t. Tap [Settings]u[Wireless & networks]u[Bluetooth settings]. 3 Tap [Scan for devices]. 4 Tap a Bluetooth device name to pair with the terminal. 5 If necessary, enter the passkey (PIN). ･ A list of detected Bluetooth devices appears. Connecting the terminal with another Bluetooth device 1 2 From the Home screen, tap t. 3 Touch and hold a Bluetooth device name you want to connect. Tap [Settings]u[Wireless & networks]u[Bluetooth settings].
Deactivating the connection of a Bluetooth device 1 2 3 From the Home screen, tap t. 1 2 From the Home screen, tap t. Touch and hold the currently connected Bluetooth device name. 3 Touch and hold the currently connected Bluetooth device name. The pairing and connection status is shown below the connected device name. 4 Tap [Disconnect & unpair]. Tap [Settings]u[Wireless & networks]u[Bluetooth settings]. ･ 4 Canceling the pair setting of a Bluetooth device Tap [Disconnect].
Sharing files with DLNA devices via Connected devices (Media server) With Media server, you can share media files with other client (DLNA: Digital Living Network Alliance) devices using Wi-Fi function. Set Wi-Fi connection (P.112) with another client device. Setting Connected devices (Media server) 1 From the Home screen, tap , then tap [Connected devices]. ･ 2 If you activate for the first time, "Welcome!" screen appears. Tap [Done]. ❖Information ･ Tap t to set Wi-Fi connection or check help.
Playing a media file in the terminal with a DLNA device Set Wi-Fi connection on a DLNA device in advance. 1 2 From the Home screen, tap , then tap [Connected devices]. Tap t, then tap [Media server] to mark [Share contents] checkbox. 3 Tap [OK] to mark [Wi-Fi] checkbox. 4 Tap y and tap 5 Tap an album, then tap a file you want to play. 6 Tap t and [Play on]. 7 Tap a device displayed on the "Play on device" screen. ･ ･ ･ ･ "Media server turned on" appears in the status bar. and [Gallery].
Applications Shooting with the camera You can shoot still picture and video by tapping the shutter icon or screen or using the camera key (k). You can hold the camera horizontally or vertically to shoot still pictures (when shooting with 3D Sweep Panorama/Sweep Multi Angle/Sweep Panorama, hold the camera horizontally). For recording videos, screen display supports landscape only. Still pictures and videos are saved automatically in the internal storage or a microSD card.
Note on 3D Sweep Panorama/Sweep Multi Angle/Sweep Panorama ･ In the following cases, 3D Sweep Panorama/ Sweep Multi Angle/Sweep Panorama do not work properly. - Shooting a moving object - Shooting the main object that is too close to the camera - Shooting an object with repetition of the same pattern such as a sky, beach, grass, etc. - Shooting a big object - Shooting an object with constantly changing pattern such as a wave, waterfall, etc.
･ Tap to open viewing/playback screen for still Shooting screen and key operations ■ pictures and videos. ･ Tap the icon displayed by touching and holding Still picture shooting screen c d a e f b to perform the following operations. : View playback screen of photos and videos : Share : Delete g Select scenes h Exposure value setting i Turn Photo light On/Off ❖Information ･ On the shooting screen, press m to zoom in/ out.
1 From the Home screen, press and hold k for over a second. ･ The still picture shooting screen (P.174) appears. ■ Tapping the shutter icon ( ) Tap the shutter icon ( ) on the shooting screen. ･ To take a photo using auto-focus function, touch and hold the shutter icon ( ) and release your finger when the focus frame turns green and sound beeps. The photo is taken as soon as you release the finger. If the focus frame turns red, auto-focus does not operate correctly.
Shooting using Quick launch 1 ❖Information ･ For using Front camera, "Resolution", "Self-timer", On the key/SIM/screen unlock screen, press and hold k for over a second. ･ The camera is activated to shoot a photo immediately. Shot pictures are automatically saved in the internal storage/microSD card. ❖Information ･ "Quick launch" (P.185) is set to "Launch and capture" by default. The operation of Quick launch can be selected from "Launch and capture", "Launch only", and "Off".
Face detection You can use face detection to bring an offcenter face into focus. The camera automatically detects up to 5 faces at a time. A yellow frame indicates a face to focus on, and white frames indicate the rest. An appropriate face is determined by distance from the camera and off-center balance, and is focused automatically. You can also tap one of the frames to select which face should be in focus. Setting face detection 1 From the Home screen, press and hold k for over a second.
Smile detection Smile detection allows you to capture a face just as it smiles. The camera detects up to 5 faces and selects 1 face for smile detection and auto focus. A yellow frame shows which face is selected. When the selected face smiles, the frame turns to green and the camera automatically takes a photo. Setting smile detection 1 From the Home screen, press and hold k for over a second. ･ 2 The still picture shooting screen (P.174) appears.
Using Sweep Panorama Use Sweep Panorama to shoot panoramic image with wide angle. Aligning the white frame on the screen with the black frame, move the camera slowly toward the set shooting direction to shoot. Using 3D Sweep Panorama allows you to shoot 3D pictures. Using 3D Sweep Panorama/Sweep Multi Angle/Sweep Panorama to shoot pictures 1 With 3D Sweep Panorama/Sweep Multi Angle/Sweep Panorama set, point the camera at the subject. 2 Shoot a still picture.
Changing the recording settings 1 From the Home screen, press and hold k for over a second. ･ 2 The still picture shooting screen (P.174) appears. On the shooting screen, tap t, then tap the setting item. ･ Several setting icons are displayed on the shooting screen in advance. The displayed setting icons change depending on the setting conditions. ･ While using 3D Sweep Panorama/ Sweep Multi Angle/Sweep Panorama, tap the setting item icon displayed on the shooting screen to change the setting.
Still camera setting Item Capturing mode Scenes Icon Description Select the shooting method. Scene The camera determines recognition most suitable scene effect. A corresponding scene icon appears when the scene is recognized. Normal A standard shooting mode. Front P.176 camera 3D P.179 Sweep Panorama Sweep Multi Angle Sweep Panorama Use Scenes to quickly set up the camera for various scene conditions. Use when "Capturing mode" is set to "Normal". OFF Adjust color shade or brightness automatically.
Item Resolution Icon Description Select image sizes and aspect ratios before shooting. An image with a higher resolution requires more memory. 12MP 12 megapixel image size 4:3 with 4:3 aspect ratio. Suitable for viewing on normal size screen or printing in high resolution. 9MP 9 megapixel image size 16:9 with 16:9 aspect ratio. A high resolution widescreen format. A higher resolution than full HD. Suitable for viewing on wide-screen. 2MP 2 megapixel image size 4:3 with 4:3 aspect ratio.
Item Self-timer Smile detection Icon Description Use it to take self-portraits, or group photos where everyone can be in the photo. You can also use the self-timer to avoid camera shake. On Tap or press k to (10 sec.) shoot 10 seconds later. On Tap or press k to (2 sec.) shoot 2 seconds later. Off Tap or press k to shoot immediately. Shoot faces at the moment they smile. The camera detects up to 5 faces and selects 1 face for smile detection and auto focus.
Item ISO White balance Icon Description Set ISO sensitivity. Shoot clear picture reducing blur even in a place where lightning is poor. Use when "Capturing mode" is set to "Normal". Auto Set to the appropriate sensitivity between " 100" and " 800". 100 Set sensitivity to 100. 200 Set sensitivity to 200. 400 Set sensitivity to 400. 800 Set sensitivity to 800. The white balance setting adjusts the color balance according to the light source. Use when "Capturing mode" is set to "Normal".
Item Icon Description Geotagging Tag photos location information for the shooting spot. You need to mark "Use wireless networks" (P.211) or "Use GPS satellites" (P.211) checkbox in "Location & security" settings beforehand. For details on location information, see "About location services" (P.209). ･ Geotag (location information) enables to specify the shooting spot of the photo. On Location information is added to the taken photo. Off Shooting location cannot be viewed on a map.
Item Data storage ■ Tapping the screen Icon Description Set the saving location for shot images. Internal Save shot images in the storage internal storage. SD card Save shot images in a microSD card. On the recording screen, tap tu"Capturing method"u"Touch capture"uTap the screen to start recordinguTap the screen to stop recording. ■ Using camera key (k) ❖Note ･ Some settings cannot be used in combination with On the recording screen, press k to start recordinguPress k to stop recording.
❖Information ･ For using Front video camera, "Video size", "Self- timer", "Microphone", "Capturing method", "Data storage" can be set. Other "Video camera setting" (P.188) are not supported by Front camera. - The settings take over the video settings set at the time when switching (if "Video size" is set to "Full HD", the video size is changed to "HD 720p"). 4 Drag at the right of the progress bar to the left, to the end point of cropping. ･ 5 Tap [Save].
3 Tap an option in the selected setting. ･ If you change setting options, icons displayed on the shooting screen change to the set items. Video camera setting Item Recording mode ❖Information ･ On the recording screen, tap t to display setting items. If you touch and hold an item and then drag it to the left, you can replace setting item icons displayed on the recording screen.
Item Video size Icon Description Full HD Full wide HD format with 16:9 aspect ratio. 1920u1080 pixels Use when "Capturing mode" is set to "Video camera". HD HD format with 16:9 720p aspect ratio. 1280u720 pixels VGA VGA format with 4:3 aspect ratio. 640u480 pixels Photo light Use the photo light to record when lighting conditions are poor or in backlight. On The photo light turns on. Off The photo light does not turn on.
Item White balance Icon Description The white balance setting adjusts the color balance according to the light source. Auto Adjust the color balance automatically to the light source. Adjust the color balance Incandescent for lighting like incandescent bulb. Adjust the color balance Fluorescent for lighting like fluorescent. Daylight Adjust the color balance for a sunny place. Cloudy Adjust the color balance for a cloudy sky or shaded area.
Item Capturing method Data storage ❖Note Icon Description Set the shooting method. Set to start/stop On-screen recording videos by tapping the record button starting/stopping icon or pressing k. Touch Set to start/stop capture recording videos by tapping the recording screen or pressing k. Set to start/stop Camera key recording by pressing k. only Set the saving location for recorded videos. Internal Save recorded videos in storage the internal storage. SD card Save recorded videos in a microSD card.
Playing multimedia content You can view/play multimedia contents (music, photos, videos, etc.) on "Music Player", "Gallery", "Media Player", etc., respectively. You can play photos and videos shot by the terminal, transfer files to the built-in storage by connecting to a PC, and play multimedia content of the following file formats downloaded from the Internet.
Using Stereo Headset with Microphone 1 Connect the plug of Stereo Headset with Microphone (Sample) to headset connector of the terminal. ･ Check the connecting direction to connect correctly. Wrong connection may cause damage. ❖Information ･ When you listen to Music player/FM radio with Stereo Headset with Microphone (Sample) connecting to the terminal, you can switch on/off by pressing the switch of Stereo Headset with Microphone (Sample).
■ Viewing photo/video album Photos and videos that you took or saved in the internal storage or microSD card from a PC are displayed in albums. 1 From the Home screen, tap then tap [Gallery]. ･ ･ 2 , Album list screen appears. If you signed in online service available to be synchronized such as Facebook/ Google+/Picasa, online albums also appear after synchronization. Tap an album you want to view. ･ A screen listing Photo/Video files in album appears.
❖Information ･ Still pictures shot with Sweep Multi Angle also appear in the album of 3D Sweep Panorama. ･ Still pictures saved in (3D Sweep Panorama) can be viewed three-dimensionally by connecting with a 3D viewing device. ･ Still pictures saved in (Sweep Multi Angle) can be viewed three-dimensionally by tilting the terminal left and right. Operating Photo/Video files in album 2 Tap t, then tap displayed menu.
■ ❖Information Still picture viewing screen ･ While selecting a file, tap t and tap [Play on] to display the connection device selection screen (if you do not connect Wi-Fi network in advance, tap [Settings] to display the setting screen for wireless & networks). Select a device detected on the connection device selection screen, and tap the device name to play on to share a file between a DLNA device and the terminal.
Adjusting the volume of a video Playing video 1 From the Home screen, tap then tap [Gallery]. 2 Tap an album. 3 ■ ･ , A list screen of files in the album appears. icon is displayed on the video files. Tap a video. a ❖Information ･ Volume can be adjusted by operating the playback volume adjustment bar on the video playback screen. 1 b c On the video playback screen,press top or bottom of m.
❖Information Playing YouTube video ･ For movies with caption function which can display YouTube is a free online video streaming service. You can play, search for and upload videos. ･ A packet communication charge is applied when downloading or uploading video content using 3G network. subtitles, "CC" appears on the playback screen in the landscape mode. For your first activation, tap [CC] and tap language for the subtitles.
Searching for a video with keywords 1 On the YouTube video list screen, tap t, then tap [Search]. 2 3 Enter the search keyword. Scroll the result and tap a video you want to play. Deleting search history 1 On the YouTube video list screen, tap t, then tap [Settings]. 2 [Clear search history]uTap [OK]. Connecting the terminal to TV to watch photos and videos You can watch photos and videos on television by connecting the terminal using an HDMI cable (type D).
2 Scroll an icon left and right to select the desired application. ･ When you connect an HDMI cable for the first time, "HDMI cable connected" appears. - On the "HDMI cable connected" screen, tap [Learn more] to show how to use the TV remote controller. ･ You may be able to operate applications with the TV remote controller. ❖Information ･ While HDMI is connected, drag the status bar ･ ･ ･ ･ ･ ･ downward and tap [HDMI connected] to set HDMI control or output.
■ Music player screen a b c ❖Information h i d e j f g k a Playing tab b Artist name, song title, album title c Favorites/"Like" icon ･ Display when added to Favorites or "Like" specified. d Album art : Tap to display "Like"/Add to favorites/ Play on device/Play queue. ･ "Like" appears if you log in to Facebook. e [Previous] key : Go to the previous track, or to the beginning of the track in the current playlist. f Progress bar : Resume playback from the specified point by dragging or tapping.
･ On the unlocking screen, flick left around date to display the Music player widget to operate by tapping Play/Pause/[Rewind]/[Forward] key without unlocking the keys. While playing music, Music player widget automatically appears on the key unlock screen. ･ You can return to the Home screen to perform another operation while listening to the Music player in the background.
Deleting a track 1 In the Music player screen, tap [MY MUSIC] tab. 2 Tap TRACKS/ALBUMS/ARTISTS/ PLAYLISTS/MY FAVORITES category. 3 Touch and hold a track you want to delete. 4 Tap [Delete]u[Delete]. Using a track as a ringtone Playlist In Music player, you can create new playlists with your desired tracks. You can use Media Go (P.162) to maintain your music library and create your own playlists. Playlists that you create by yourself are stored on the terminal in the m3u format.
Playing Playlists 1 In the Music player screen, tap [MY MUSIC] tab. 2 Tap [PLAYLISTS]. ･ The following playlists appear by default. My favorites Newly added Most played Never played 3 Display the list of tracks in My favorites. Display the list of tracks newly added. Display the list of frequently played tracks. Display the list of available tracks which have not played wholly. Tap a playlist you want to playuTap a track. ･ The playlist plays from the track you tap.
❖Information Timescape™ ･ Be sure to check the security of application, then ･ ･ ･ ･ install it at your own risk. The terminal may be infected with a virus and the data may be damaged. NTT DOCOMO is not liable for malfunctions, if any, caused by the application you installed. In such case, the repair is charged even during the warranty period. NTT DOCOMO is not liable for any disadvantage brought to you or any third party due to an application you installed.
Setting up Timescape ･ Timescape screen The first time you start Timescape, a setup wizard will guide you the necessary steps to set up account. 1 From the Home screen, tap then tap [Timescape™]. 2 3 Tap a tile. If you want, enter your Facebook/ Foursquare/Twitter/mixi account information. 4 a , Tap [Done]. ❖Information ･ In the setup wizard, tap [Extension search] on the account registration screen to connect to Android Market and search new services for Timescape.
Posting to Facebook, Foursquare, Twitter, mixi from Timescape Filter icons Filter Icon Displayed tile All tiles Updates from your Facebook contacts Updates from your Foursquare contacts Updates from your Twitter contacts Updates from your mixi contacts 1 On the Timescape screen, tap t and tap [Update status]. 2 Mark the service you want to post and tap [Continue]. Enter the text and tap [Post]. 3 Filtering the displayed tile 1 Tap the filter icons on the Timescape screen.
Tile icons The following icons on a tile indicate a type of event. Icon Event A Facebook update. Tap the tile to display the update. A Foursquare update. Tap the tile to display the update. A Twitter update. Tap the tile to display the update. A mixi update. Tap the tile to display the update. Displaying tile information 1 On the Timescape screen, tap a tile. The infinite button in Timescape When you tap a tile, (infinite button) may appear in the upper right corner.
About location services There are two ways to find your location, using Mobile networks with Wi-Fi (Wireless network) or GPS. Wireless network technology determines your position fast but accuracy may vary. If you use GPS technology it may take a little longer, but it will find your exact position. You can enable both Wireless network and GPS to benefit from both technologies when trying to find your position.
･ You cannot use the terminal as a navigation device for an aircraft, vehicle, and person. Note that DOCOMO shall have no liabilities whatsoever even if you suffer damage or loss while performing a navigation using the location information. ･ You cannot use the terminal as a highaccuracy measurement GPS. Note that DOCOMO shall have no liabilities whatsoever even if you suffer damage or loss due to a deviation of the location information.
Enabling GPS function 1 From the Home screen, tap t and tap [Settings]. 2 3 4 Tap [Location & security]. Tap [Use GPS satellites]. Read the note and tap [Agree]. ･ [Use GPS satellites] is marked. Enabling Wireless networks to find position ･ Enable to search a current location using mobile network and Wi-Fi. 1 From the Home screen, tap t and tap [Settings]. 2 3 4 5 Tap [Location & security]. Tap [Use wireless networks]. Read the note and tap [Agree].
Viewing Street View ･ Street View does not cover some areas. 1 2 3 Touch and hold a spot on the map that you are going to look at in Street View. Tap the displayed call-out. Tap ･ Searching for a location you want to look at 1 On the map screen, tap t, then tap [Search]. 2 Fill out the search box. 3 Tap 4 Tap a destination. (Street View)u[OK]. On the Street View display, tap t and tap [Compass mode]. The compass in Street View shows the same direction as the terminal's geomagnetic compass.
Zooming in or out on a map 1 Tap map. to zoom in or out on a ❖Information ･ Alternatively, double-tap or pinch on the screen to zoom in/out. Receiving guides Google Maps helps you receive detailed guides for your destination. 1 2 Changing the layers ･ You can select information to overlay on the map. 1 2 On the map screen, tap . Tap the information you want to view. ･ Traffic information and routes are not available in all locations.
Clearing the Maps Joining Latitude Clear displayed layers, route search results and some others. 1 1 ･ For the first time to join Latitude, a message confirming whether to agree to share location information with friends appears. ･ Once you join Latitude, the menu name changes into [Latitude]. On the map screen, tap t and tap [Clear Map]. ･ If there is nothing to clear, "Clear Map" is displayed in light gray.
1Seg 1Seg is a terrestrial digital TV broadcasting service that allows mobile devices to receive broadcasted data along with images and sounds. You can also acquire detailed program information, participate in quiz programs, enjoy TV shopping, etc. For details on "1Seg", refer to the following website. The Association for Promotion of Digital Broadcasting http://www.dpa.or.jp/ Using 1Seg 1Seg is a service provided by TV broadcasting enterprises (stations), etc.
･ A place far from the tower that the airwaves are sent from ･ Mountain-ringed regions or a place between buildings where airwaves are interrupted by geography or buildings ･ Tunnel, underground or far back from a building where airwaves are weak or do not reach ･ 1Seg antenna can be rotated by 360 degrees. Use 1Seg antenna in the direction you can receive a stronger airwaves. 1Seg antenna To make the reception condition better, stretch out the 1Seg antenna.
3 4 Tap [YES]. ･ If the terminal receives a call while watching 1Seg, Tap entry box, enter a title name and tap [OK]. ■ ･ 1Seg is interrupted and resumes after the call ends. 1Seg screen To go back to 1Seg menu, tap x. c ❖Information a ･ Alternatively, tap [Select area] in Step 2 then select area to make channel setting. b ･ Channel setting may not be made in the area where a terrestrial digital TV broadcasting service has just started.
a b c d Image Subtitle Program information Switch screen view : Switch screen between full screen data broadcasting and 1Seg program with data broadcasting (only for vertical view). e Advanced settings f DOWN selection/UP selection : Select previous or next channel you are currently watching. g Remote controller : Display numeric keys 1-12 to switch channels and keys for searching stations. h Mute i Data broadcasting : Display data broadcasting content.
Reset confirmation status Back to data BC Tune service Initialize the confirmation screen display. Display data broadcasting. You can select a sub-channel when several programs (services) are broadcasted for separated subchannels in a channel. TVlink Stored TVlinks appear. Operation guide A guide for watching 1Seg appears. Using TVlink For some data broadcasting programs, link information to related websites (TVlink) is displayed. Save TVlinks to connect to related websites later.
Viewing/Deleting details of TVlink 1 From the Home screen, tap and then tap [1Seg]. 2 Tap [TVlink] and tap t. ･ , A menu list appears. Check the number of registration Delete all Delete selected Check the number of stored TVlinks. Delete all stored TVlinks. Delete several stored TVlinks. Mark TVlink to delete and tap t, tap [Delete data?]u[YES]. Storing/Changing broadcasting service areas Available channels vary depending on the area (broadcasting service area) you are using in.
■ Using menus on the channel list selection screen Touch and hold the channel list selection screen to display menus for displaying information, setting, editing titles, deleting, etc. Making User setting You can set, initialize, and reset watching screen, data broadcasting screen from User setting. Initializing settings Changing numbers for TV remote You can initialize the channel setting and 1Seg setting. Change TV remote number assigned to each broadcasting station.
3 FM radio You can listen to the FM radio with the terminal. Tuning can be made automatically or manually, and you can register your favorite channels to Favorites. To use FM radio, use a handsfree device such as Stereo Headset with Microphone (Sample), etc. or a headphone. They work as antenna. ･ Alternatively, tap / to search for channels. ･ The search ends when radio waves are received. 4 Tap , then tap [+ Add XX.X to favorites]. 5 Tap entry box, enter a name and tap [Save].
■ FM radio screen a b d c e f g h i j a Monaural sound/stereo effect b Play in speaker/Play in handsfree c Channel point displayed in a good radio wave condition d On/Off of FM radio e Broadcasting station now listening f Channel assigned to favorite g Search channels automatically h Move left to select next favorite i Tuning button ( for Favorites) j Move right to select next favorite Osaifu-Keitai Osaifu-Keitai equipped with IC card is a function which allows you to pay money or to use coupon,
Precautions on using Osaifu-Keitai ･ The data (including electronic money, points, etc.) in the IC card may be lost or modified because of the malfunction of the terminal (When we take your Osaifu-Keitai for repair etc., as we cannot take it with data remained, you are required to erase the data by yourself ). For support such as reissuance, restoration, temporary preservation or transfer of data, contact Osaifu-Keitai compatible service providers.
･ If mark is not recognized even when holding over the IC card reader, try slightly picking the terminal up off the reader, or moving the terminal back, forth and around. ･ If there are metal objects between mark and an IC card reader, scanning may be failed. And note that a sticker put on nearby the mark may affect communication performance. ❖Information ･ You can scan and write data to or from an IC card reader without activating Osaifu-Keitai compatible application.
iD 設定アプリ (iD setting application) iD is a convenient electronic money by credit clearance scheme. You can enjoy shopping simply and conveniently only by holding Osaifu-Keitai with credit information set or the iD-compatible card over the IC card reader in stores. Because up to 2 types of credit information can be registered in Osaifu-Keitai, you can use them according to the benefits, etc. It also supports cashing, depending on the card issuer.
･ When you send ToruCa attaching to email, it is sent Calendar in the condition before obtaining ToruCa (details). ･ Depending on email application, ToruCa received via the emails may not be saved. ･ Depending on browser, ToruCa cannot be obtained. ･ When ToruCa is moved/copied to the microSD card, it is moved/copied in the condition before obtaining ToruCa (details). ･ You may not be able to obtain ToruCa with an IC card reader, if you do not make initial setting for OsaifuKeitai.
Creating a schedule in Calendar 1 2 From the Home screen, tap then tap [Calendar]. Tap ･ , Tap t and tap [New event] to create a schedule in Calendar. Enter a schedule name, date, and time. 4 If you have two or more calendar accounts, select one. If necessary, select the repetition intervals of the calendar. Select the notification intervals of the schedule. 6 ･ 7 8 1 From the Home screen, tap then tap [Calendar]. ･ at the upper right.
･ If you tap [Snooze all], all the alarms sound again 5 minutes later. (Snooze is a function that sounds the alarm some time later even though you stop it.) Changing the calendar settings Set Calendar view, reminder notifications, ringtone, vibration, reminder time. 1 2 3 From the Home screen, tap then tap [Calendar]. Alarm and Clock With "Alarm and Clock" application, you can set an alarm, show the clock or photo slideshow on the display, or play music with the Media player.
❖Information ･ If you tap t on the Clock screen, "Dock settings" appears. However the dock compatible to this function is not sold by Sony Mobile Communications Japan, Inc. (as of February, 2012). Setting alarm 1 From the Home screen, tap , then [Alarm and Clock]uTap . ･ 2 The alarm list screen appears. Tap [Add alarm]. ･ An alarm setting screen appears. You can set the following items.
Stopping an alarm while the alarm is sounding 1 While alarm is sounding, touch and drag it to the right. Using World clock Display the date and time in cities around the world. 1 2 3 4 From the Home screen, tap , then [Alarm and Clock]uTap . Tap [World clock]. ･ The list screen of the world clock appears. Tap [Add new]. Drag the screen up and down to select a city. Changing World clock You can switch, sort or delete Celsius/ Fahrenheit displayed on World clock.
Using Stopwatch 1 2 3 4 From the Home screen, tap , then [Alarm and Clock]uTap . Tap [Stopwatch]. Using Timer 1 2 Tap [Start]. ･ Measurement starts and appears in the status bar. ･ Tap [Lap] to measure elapsed time. Tap [Stop]. ･ ･ Tap [Start] to resume measuring. Tap [Reset] to delete measured time and lap time. From the Home screen, tap , then [Alarm and Clock]uTap . Tap [Timer]. ･ Time screen appears. 3 4 Tap [Set time]. Tap number to adjust the time and then tap [Set]. 5 Tap [Start].
SE Home OfficeSuite With OfficeSuite, you can view files of Word, Excel, etc. from the terminal or a microSD card. Starting OfficeSuite 1 2 From the Home screen, tap Tap [OfficeSuite]. ･ . OfficeSuite starts. Other applications You can use the following online services on the terminal. PlayNow PlayNow is a web application which allows you to use news flash, dictionary service, etc.
International roaming Overview of International roaming (WORLD WING) With the international roaming (WORLD WING), you can use the terminal without changing phone number or mail address in the service area of the overseas network operator affiliated with DOCOMO. You do not need to change the settings of call and SMS. ■ Service area The terminal works in a 3G roaming area and GSM/GPRS service area. Services are also available in countries and areas supporting 3G850MHz/GSM850MHz. Check available areas.
Before using Before leaving Japan To use the terminal overseas, check the following in Japan. ■ ■ Subscription ･ Check if you subscribe WORLD WING. For details, contact "General Inquiries" on the last page of this manual. Usage charge ･ Overseas usage charges (call and packet communication) differ from those in Japan. ･ Some applications automatically perform packet communications. Your packet communication charges may be higher.
After arriving overseas When you arrive overseas and turn on the terminal, an available network is automatically set. Connectivity When you have set search mode of "Available networks" to "Automatic" in "Service providers" settings, optimized network is automatically selected. When you connect to the network operator conducted in flat-rate service manually, you can use the service with flat-rate packet communication charges overseas up to the specified upper limit per day.
After returning to Japan When you return to Japan, the terminal is connected to DOCOMO network automatically. If connection is failed, perform the following operations. ･ Set "Network Mode" to "WCDMA (preferred)/ GSM". (P.238) ･ Set "Search mode" to "Automatic" in "Service providers" settings. (P.237) Making setting for international use When you start the international roaming or move out of your operator's network, you need to reconnect the terminal to another available network.
Changing network mode settings You can change network mode settings according to the network mode (communication method) adopted by the overseas network operator. 1 From the Home screen, tap t and tap [Settings]. 2 Tap [Wireless & networks]u[Mobile networks]u[Network Mode]. Select a network mode you use. 3 ･ You can select from [WCDMA only], [GSM only] or [WCDMA (preferred)/ GSM]. If you select [WCDMA (preferred)/GSM], you can use both GSM and WCDMA.
2 Dial + (touch and hold [0])uCountry codeuArea code (City code)uEnter a phone number. ･ If the area code begins with "0", omit "0". However, "0" may be required to dial to some country or area such as Italy. ･ To call an overseas "WORLD WING" user, enter "81" (Japan) for the country code. ･ You can enter country code using the preset Convert country code list. Enter a phone number and tap t to tap [International call], then select country code from the Convert country code.
1 While receiving a call, touch (left) and drag it to (right). 2 When the conversation is finished, tap [End call]. ❖Information International roaming settings Make settings for using international roaming or international calls. ･ When you received a call during the international roaming, regardless of which country the call is from, it is forwarded internationally from Japan. A caller is charged for a call fee to Japan, and the receiver is charged for a reception fee.
Check settings Check the current service settings. Settings Network service (overseas) Setting roaming guidance Set network service such as voice mail from overseas. ･ If you make the settings overseas, you are charged a call fee to Japan from the country you stay. ･ For some overseas network operators, settings may not be made. 1 2 3 From the Home screen, tap t and tap [Settings]. Tap [Call settings]u[Network service setting]u[Roaming settings]. Tap [Roaming guidance].
Voice mail Voice mail Tap [OK], and then tap (charged) ring time (roaming) Roaming guidance Tap [OK], and then tap (charged) Remote operation Tap [OK], and then tap (charged) .* .* .* * Follow the voice prompts to operate.
Appendix/Index Optional and related devices A variety of commercially available optional devices allows you to expand the terminal's capabilities by supporting a wide range of purpose, including personal and business uses. Some accessories are only available in some areas. For details, please contact a sales outlet such as docomo Shop. For details on optional devices, see the user's manual of each device.
Screen does not respond. I cannot turn the power off. ･ Press p and upper of m at the P.38 same time for approximately 5 seconds, and release your finger after the terminal vibrates once to restart the terminal. Or, press p and upper of m at the same time for approximately 10 seconds and release your finger after the terminal vibrates 3 times to turn off the terminal forcibly. ■ Charging Cannot charge the terminal. (The notification LED does not turn on, or the icon that means charging does not appear.
The screen reacts slowly when a button is pressed. ･ When large amount of data is saved in the − terminal or transferring large-size data between the terminal and microSD card, the reactions on the screen may be delayed. The UIM is not recognized. ･ Check if the UIM attached in the right P.30 direction. The clock is not on time. ･ The clock time may become wrong while P.139 turning on the power for a long time.
Calls are not connected. (Even when moving "圏外 (out of service area)" does not disappear, or although radio waves are enough, making/receiving calls is unavailable.) ･ Turn the power OFF and ON, or remove and P.30 attach UIM. P.37 ･ Due to the nature of radio waves, making/ − receiving calls may be unavailable even when "not out of service area" or " appears on the display for the radio wave condition". Move to the other place and call again.
■ Osaifu-Keitai Osaifu-Keitai function is unavailable. ･ Is Osaifu-Keitai lock activated? ･ Do you place mark of the terminal over an IC card reader? ■ P.225 P.224 International roaming Cannot use the terminal overseas. ■ When antenna mark is displayed ･ Do you subscribe WORLD WING? Check if you subscribe WORLD WING. ■ Out of service area indicator appears ･ Check if you are out of the international − P.236 P.238 roaming service area or in an area with poor P.37 signal strength.
When trying to display an image, "u" appears instead of it. Or "u" appears for the demo play or the preview function. ･ "u" may appear instead of destroyed image − data. ■ Bluetooth function The terminal cannot be connected to a Bluetooth communication device/A Bluetooth communication device cannot be found from the terminal. ･ Make Bluetooth communication device P.167 (commercial item) registering stand-by state and then register the device on the terminal.
Warranty and After Sales Services Warranty ･ Make sure that the warranty is received with the terminal upon purchase. Check to be sure that " 販売店名・お買い上げ日 (the name of the retailer, date of purchase)", and other items have been filled out on the warranty before storing it in a safe place. If any necessary information is not provided, immediately contact the retailer and request to complete the warranty. The terminal comes with a year's free warranty starting from the date of purchase.
･ When requesting a repair, make sure to bring the warranty card with the terminal. Repair requests that are not accompanied by the warranty or that involve malfunction and damage due to incorrect handling by the owner (damage of liquid crystal, connector, etc.) will only be repaired at the owner's expense, even if the warranty period is still effective.
The following cases may be considered as modifications. - Put a seal etc. on the liquid crystal or keypad. - Glued decorations on the terminal using adhesion bond, etc. - Change the parts such as exterior to other than DOCOMO standard parts. ･ Malfunction and damage due to modifications will be repaired at the owner's expense, even if the warranty period is still effective. ● The model plate must not be removed from the terminal. The model plate certifies that the terminal satisfies technical standards.
Updating software You can update the terminal to the most recent software for optimal performance and to get the latest enhancements. ❖Note ･ When the terminal is connected to the Internet using the mobile network connection, data communication fee is applied. ･ Make sure you back up and save all data contained in the terminal before you start updating the terminal.
Downloading software updates wirelessly Downloading software to update Software can be downloaded wirelessly directly from your terminal via the Internet by using mobile network connection or by using a Wi-Fi network connection. 1 2 From the Home screen, tap , then tap [Update center]. Tap [System] tab, then tap t, and then tap [Refresh]. ･ The terminal searches for software updates.
Connecting to a PC and updating You can update software by using PC Companion that can be installed into a PC from the terminal. ❖Information When PC Companion is installed on your PC 1 Check if PC Companion is activated on the PC. If not, activate PC Companion from the Start menu. 2 Connect the terminal to a PC using a microUSB cable. 3 Follow the onscreen instructions on the PC. ･ To install PC Companion on a PC, an Internet connection is required.
Main specification ■ The terminal Product name Size SO-04D Approx. 126mm (H)u approx. 66mm (W)u approx. 11.9mm (T) (Thickest part : Approx. 11.9mm) Weight Approx. 149g Storage ROM 16GB RAM 1GB External storage Compatible with microSD card of up to 2GB, and microSDHC card of up to 32GB (as of February, 2012). Continuous FOMA/3G Approx. 410 hours stand-by (stationary) time GSM Approx. 290 hours (stationary) Continuous FOMA/3G Approx. 430 min. call time GSM Approx. 400 min. Charging AC Adapter Approx.
Music playback MP3 file Continuous playback time Approx. 1380 min. (Background playback supported) Wireless LAN Compliant with IEEE802.11b/g/n (Corresponding frequency band to IEEE802.11n : 2.4 GHz) Bluetooth Supported Compliant with Bluetooth Bluetooth standard Ver. version 2.1 + EDR*1 Radio power Bluetooth standard Power Class 1 Available Within approx.
■ ■ Internal battery Battery type Lithium Ion Battery Voltage DC3.7V Current 1840mAh ■ File format The terminal supports the display or playback of the following file format: Type Sound Still image Video File format MP3, 3GPP, MP4, AMR, AMRWB, SMF, XMF, WAV, iMelody, RTTTL/RTX, OTA, Ogg vorbis JPEG, GIF, PNG, BMP 3GPP, MP4 * Still images are saved in JPEG format.
Specific Absorption Rate of Mobile Phone, etc. Mobile phone: GSM/GPRS/EDGE 850/900/ 1800/1900 & UMTS/HSPA B1/5/6/19 & LTE B1 Specific Absorption Rate of Mobile Phone This model SO-04D mobile phone complies with Japanese technical regulations and international guidelines regarding exposure to radio waves.
potential health risk. To date, no adverse health effects have been established as being caused by mobile phone use." Please refer to the WHO website if you would like more detailed information. http://www.who.int/docstore/peh-emf/ publications/facts_press/fact_english.htm Please refer to the websites listed below if you would like more detailed information regarding SAR. Ministry of Internal Affairs and Communications Website: http://www.tele.soumu.go.jp/e/sys/ele/ index.
standards include a safety margin designed to assure the safety of all individuals, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardized methods with the phone transmitting at its highest certified power level in all used frequency bands.
* In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/ kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a margin of safety to give additional protection for the public and to account for any variations in measurements. ** This paragraph is only applicable to authorities and customers in the United States.
Guidelines for Safe and Efficient Use Please follow these guidelines. Failure to do so might entail a potential health risk or product malfunction. If in doubt as to its proper function, have the product checked by a certified service partner before charging or using it. ■ Recommendations for care and safe use of our products ･ Handle with care and keep in a clean and dust-free place. ･ Warning! May explode if disposed of in fire. ･ Do not expose to liquid or moisture or excess humidity.
■ Children Warning! Keep out of the reach of children. Do not allow children to play with mobile phones or accessories. They could hurt themselves or others. Products may contain small parts that could become detached and create a choking hazard. ■ Power supply (Charger) Connect the charger to power sources as marked on the product. Do not use outdoors or in damp areas. Do not alter or subject the cord to damage or stress. Unplug the unit before cleaning it. Never alter the plug.
■ Personal medical devices ■ Mobile phones may affect implanted medical equipment. Reduce risk of interference by keeping a minimum distance of 22 cm (8.7 inches) between the phone and the device. Use the phone at your right ear. Do not carry the phone in your breast pocket. Turn off the phone if you suspect interference. For all medical devices, consult a physician and the manufacturer. ■ Some products provide GPS/Location based functions.
■ Antenna Use of antenna devices not marketed by Sony Mobile communications AB could damage the phone, reduce performance, and produce SAR levels above the established limits. Do not cover the antenna with your hand as this affects call quality, power levels and can shorten talk and standby times. ■ Radio Frequency (RF) exposure and Specific Absorption Rate (SAR) When the phone or Bluetooth handsfree is turned on, it emits low levels of radio frequency energy.
■ Flight mode ■ Bluetooth and WLAN functionality, if available in the device, can be enabled in Flight mode but may be prohibited onboard aircraft or in other areas where radio transmissions are prohibited. In such environments, please seek proper authorisation before enabling Bluetooth or WLAN functionality even in Flight mode. ■ Use only Sony Mobile communications AB branded original accessories and certified service partners. Sony Mobile communications AB does not test thirdparty accessories.
■ ■ Disposing of the battery Warning! Check local regulations or call a Sony Mobile communications AB Contact Center for information. Never use municipal waste. If the device requires an adapter for insertion into the handset or another device, do not insert the card directly without the required adapter.
･ Insert the memory card as far as it will go into any memory card adapter needed. The memory card may not operate properly unless fully inserted. ･ We recommend that you make a backup copy of important data. We are not responsible for any loss or damage to content you store on the memory card.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ･ Reorient or relocate the receiving antenna. ･ Increase the separation between the equipment and receiver. ･ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
End User Licence Agreement End User Licence Agreement Software delivered with this device and its media is owned by Sony Mobile Communications AB, and/or its affiliated companies and its suppliers and licensors. Sony Mobile grants you a non-exclusive limited licence to use the Software solely in conjunction with the Device on which it is installed or delivered. Ownership of the Software is not sold, transferred or otherwise conveyed.
About Open Source Software About Open Source Software This product includes certain open source or other software originating from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers and notices. The exact terms of GPL, LGPL and some other licenses, disclaimers and notices are reproduced in the about box in this product and are also available at http:// opensource.sonymobile.
Intellectual Property Right About the Copyright and Portrait rights Copyrighted contents you recorded or obtained from sites or Internet home pages using this product by downloading or other means, such as documents, images, music data, software, are prohibited from reproduction, transformation and transmission over public lines without consent of the copyright holders, unless intended for personal use or any other purpose permitted by law.
･ Rovi, G-GUIDE, G-GUIDE MOBILE and their logos are registered trademarks in Japan of U.S. Rovi Corporation and/or its affiliates. ･ "Liquid Identity" logo, "Xperia", "PlayNow", and "Timescape" are trademarks or registered trademarks of Sony Mobile Communications AB. ･ "APP NAVI", "acro" is a registered trademark of Sony Mobile Communications, Inc. ･ "Media Go" is a trademark or registered trademark of Sony Electronics Inc.
･ "Microsoft", "Windows", "Outlook", "Windows Vista", "Windows Server", "Windows Media" and "ActiveSync" are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. ･ This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft.
･ Other product and company names mentioned herein may be the trademarks of their respective owners. In context, TM and ® mark are omitted. ･ Any rights not expressly granted herein are reserved. All other trademarks are property of their respective owners.
Index A About phone .............................................. 140 Access point Initializing................................................ 110 Setting ..................................................... 109 Accessibility ................................................ 139 Account setting Facebook ................................................. 133 Google ..................................................... 132 Accounts & sync ......................................... 132 Auto-sync ..............
Opening .................................................. 153 Searching text ........................................ 154 Setting home page ................................ 155 Switching browser windows................ 154 Zooming in/out ...................................... 154 C Calculator ....................................................... 75 Calendar ...................................................... 227 Creating schedule .................................. 228 Displaying schedule ............
E Ear speaker volume ...................................... 84 Early Warning "AreaMail".......................... 152 eco mode ....................................................... 75 Email ............................................................ 144 Deleting ................................................... 147 Forwarding ............................................. 147 Initial settings ......................................... 144 Receiving .................................................
Format ..................................................... 137 International call ........................................... 82 International roaming service ................. 234 International roaming setting ................. 240 J Japanese syllabary keyboard ...................... 56 K Key lock Setting ........................................................ 38 Unlocking ................................................... 39 Keys .................................................................
O PUK code (Personal Unblocking Key)...... 126 OfficeSuite .................................................. 233 Online dictionary .......................................... 63 Osaifu-Keitai ............................................... 223 Osaifu-Keitai Lock Settings .................. 225 Own number ................................... 7, 90, 140 Q P PC Companion ........................................... 159 Personal area ................................................. 80 Phone language ........
Slideshow .................................................... 196 Software keyboard ....................................... 48 Software update ........................................ 252 Sound .......................................................... 119 Specific Absorption Rate of Mobile Phone ...................................................................... 258 Specification ............................................... 255 sp-mode ......................................................
WORLD CALL ................................................. 82 World clock ................................................. 231 WORLD WING ............................................. 234 X xLOUD.......................................................... 119 Xperia........................................................... 108 Xperia Japanese keyboard .......................... 47 Setting ........................................................ 60 Y YouTube ..............................................
Make various applications or charge your billing plan, check your charges and points, and more online. My docomo (http://www.mydocomo.com/) ⇒ 各種お申込・お手続き (Various applications/procedures) *In Japanese only. * "docomo ID and password" are required for use. * Please contact "General Inquiries" described on the last page of this manual if you forget or do not have "docomo ID and password". * May not be available in some cases depending on the conditions of your subscription.
General Inquiries 0120-005-250 (toll free) *Service available in: English, Portuguese, Chinese, Spanish, Korean. *Unavailable from part of IP phones. (Business hours: 9:00 a.m. to 8:00 p.m.) ■From DOCOMO mobile phones (In Japanese only) (No prefix) 151 (toll free) *Unavailable from land-line phones, etc. ■From land-line phones (In Japanese only) Repairs ■From DOCOMO mobile phones (In Japanese only) (No prefix) 113 (toll free) *Unavailable from land-line phones, etc.
