Vanguard DOC leaflet.
English MBW-200 Bluetooth™ watch ................................4 Icons .......................................................................6 Getting started ........................................................9 Using your watch ..................................................16 Troubleshooting ....................................................25 Declaration of conformity for MBW-200 ...............26 FCC statement......................................................
MBW-200 Bluetooth™ watch Thank you for purchasing the Sony Ericsson MBW-200 Bluetooth™ watch. The MBW-200 provides you with intelligent control of calls and music through your watch. You are notified when your phone rings and if you receive a text message. When your phone rings the name or number of the caller is displayed in the watch and you can mute or reject it. If your phone has a music player you can play, stop and change tracks with your watch.
Watch overview Right top key Crown key Right bottom key Display Next/Volume up key Play/Stop key Previous/Volume down key 5
Icons Status icons Incoming call Message received The Bluetooth function on. No connection to phone The Bluetooth function on.
Adjusting volume Pairing succeeded Out of range notification: connection to the phone is lost Watch in pairing mode 7
Setting icons The Bluetooth function on The Bluetooth function off Message notification on Message notification off Out of range notification on Out of range notification off Start pairing mode Instruction symbols The following symbols may appear in the User guide: Note Tip Warning 8
Getting started Box content Before you start using the watch, make sure the following items are in the box: • Charger (A) • Charging clip (B) • The MBW-200 (C) 9
Charging Make sure your watch battery is fully charged. The minimum time to fully charge is 2 hours. To charge the battery 1 2 1 Connect the charger, without the charging clip, to the mains.
2 Connect the charger to the charging clip with the symbols on the charger and clip connector facing the same direction. 3 4 3 On the charging clip, press the handle to open the clip, and slide it over the watch. Make sure the contacts of the clip are connected to the contacts on the back of the watch. 4 Wait approximately 2 hours or until the battery icon indicates charging is complete.
Setting the time To set the time • Gently pull out the crown and rotate it to set the time. When the time is set, push the crown back in until you hear a click. Pairing Your watch has to be paired with your phone before you can use it.
phone at a time. Start a new pairing procedure to use the watch with another phone. 20 cm (8”) Follow instructions in the phone User guide on how to turn on the Bluetooth function in the phone. To pair your watch with a phone 1 Turn on the Bluetooth function in your phone. 2 Turn on Bluetooth visibility in your phone. This makes your phone visible to other Bluetooth devices. 3 Press the bottom key on the watch repeatedly to select pairing mode , then press the right top key to turn on pairing mode.
If pairing is successful, the pairing icon appears and the watch vibrates. To stop pairing, press the right top key. After you have paired your watch with a phone, the watch will automatically connect to the phone as soon as the phone is on and within range. If pairing fails, you need to set the watch in pairing mode and repeat the pairing procedure. See how to set the watch in Pairing mode on page 12.
If you choose Always ask, you will always be asked if you want to reconnect each time the watch and the phone are within range. • Always allow If you choose Always allow, the watch automatically reconnects to the phone each time both devices are within range. Always allow is the preferred setting. Pairing mode To pair your watch a second time, for example, with another phone or if the first pairing failed, do this manually by setting the watch to pairing mode.
Using your watch Settings Settings are shown as icons in the display. To read more about Setting icons go to page 8. To enter the Settings menu • Press the right bottom key. To turn a setting on or off 1 Press the right bottom key repeatedly until the setting you want is centered in the watch display. 2 Press the right top key to turn the setting on or off. Calls When the phone rings, the watch vibrates and the name or number of the caller is displayed in the watch.
To mute an incoming call • Press the right top key once. To reject an incoming call • Press the right top key twice to reject a call.
Text messages When message notification is on, the watch vibrates and appears when you receive a text message. Message notification is on by default. The name or number of the sender is displayed in the watch. Go to www.sonyericsson.com/support for an overview of which phone models fully support this functionality. To change message notification status 1 Press the right bottom key repeatedly to select 2 Press the right top key to change between on off . .
To listen to music • Press and hold the play/stop key to play a track. • Press the play/stop key to stop a track. • Press and hold the next/volume up key to go forward to the next music track. • Press and hold the previous/volume down key to go to the previous track. Track info • Press the right top key three times to display track information from the phone.
To increase and decrease volume • To increase music or voice volume press the next/ volume up key. • To decrease music or voice volume press the previous/ volume down key. Battery status To check the watch battery status YYYY-MM-DD • From standby press the right top key. The phone date is also shown.
Date To check the phone date YYYY-MM-DD • From standby press the right top key once. The watch battery status is also shown. The date format shown in the watch is set to YYYY-MMDD (year, month and day).
Time To check the phone time HH:MM • From standby press the right top key twice. Watch battery status and Bluetooth function status are also shown. The time format shown in the watch is set to 24-hour, HH:MM (hour and minute). The Bluetooth function The Bluetooth function makes wireless connection to your phone possible. You have to turn the Bluetooth function off in sensitive areas like airplanes or hospitals.
2 Press the right top key to change between on . and off If battery level is low, the Bluetooth function is automatically turned off. Turn on the Bluetooth function again when the battery is fully charged. Out of range When the phone is out of range the watch vibrates and the icon appears. 2 m (6.6 ft.
The out-of-range distance varies and depends where you are. The connection may be improved if there are no solid objects between your watch and phone. If you are out of range more than 24 hours, reconnect to the phone again by pressing the right top key on the watch. To change out-of-range notification status 1 Press the bottom key repeatedly to select 2 Press the right top key to change between on off . . and Master reset Set the watch to factory default settings and delete changes you have made.
Troubleshooting Music player does not start If the music player does not start when you press the Play/Stop key then turn the music on using the phone. Battery capacity If the battery does not work properly it needs to be replaced by a certified repair centre. Software version To check software version • In pairing mode, press the right bottom key five times. To stop checking software version, press the right top key twice. Ignore the pairing request in the phone.
Declaration of conformity for MBW-200 We, Sony Ericsson Mobile Communications AB of Nya Vattentornet SE-221 88 Lund, Sweden declare under our sole responsibility that our product Sony Ericsson type DGA-0002005 and in combination with our accessories, to which this declaration relates is in conformity with the appropriate standards EN 300 328:V1.7.1, EN 301 489-17:V1.2.1, EN 301 489-7:V1.3.
FCC statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any change or modification not expressly approved by Sony Ericsson may void the user's authority to operate the equipment.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Export Regulations: Software, including technical data, is subject to U.S. export control laws, including the U.S.
