User's Guide Part 2

368
Appendix/External Devices/Troubleshooting
If Any Error Message Appears
z In the following table, error messages are written in
red, and explanation/solution and reference pages
are written in black.
z Error messages are described in alphabetical and
Kana order.
z Numbers in parentheses are codes used by the
i-mode Center as separators between transmitted
errors.
“ACMmax restriction cannot call”
● This message appears when the accumulated call
charges exceed the upper limit set in a FOMA card
(UIM) and a call cannot be made. Perform “Reset total
cost” to release the restriction.→ p.294
“Activating BOX lock Cannot download”
● There is a lock on the inbox and outbox as a whole, or
on folders using mail-linked i-αppli, so mail-linked
i-αppli cannot be downloaded or upgraded. To
download or upgrade the mail-linked i-αppli, release
the Mail box lock.→ p.112
“Activating BOX lock Unable to delete”
● There is a lock on the inbox and outbox as a whole, or
on folders using mail-linked i-αppli, so the mail-linked
i-αppli and the folders using them cannot be deleted.
To delete the mail-linked i-αppli and the folders using
them, release the Mail box lock.
If you delete only the mail-linked i-αppli, a message will
be displayed asking whether to delete the
corresponding mail folders dedicated to that i-αppli.
Select “NO”.→p.112
“Activating folder lock Cannot download”
● See “Activating BOX lock Cannot download” (p.368) for
the explanation and solution.
“Activating folder lock Unable to delete”
● See “Activating BOX lock Unable to delete” (p.368) for
the explanation and solution.
“Activating restrict dialing”
● This message appears when you attempt a prohibited
operation while Restrict dialing is set.→p.112
“Address is not valid (451)”
● Displayed when the mail has not been sent to the
specified address correctly.→ p.156
“Attached file is deleted”
● This message appears when an i-mode message
received that you attempt to quote to send a reply has
any file attached. It is also displayed if you attempt to
forward an i-mode mail that has a file attached that is
prohibited from being attached to mail or output from
the FOMA terminal. The attached file is deleted when
you press d.
“Authentication canceled (401)”
● This message appears when the Cancel button is
pressed on the Authentication screen.
“Authentication type is not supported (401)”
● This message appears when authentication fails. Press
d to return to the original page.
“Cannot dial by Number B abroad Dial by Number
A”
● This message appears when the 2in1 mode is set to B
mode and you attempted to make a call while overseas.
Select OFF for “Caller ID Notification” to make calls
without caller ID with Number A.
“Cannot reset by this Ext. IC card”
● This message appears when you put the FeliCa mark
close to an unregistered contactless IC card during
user authentication with the IC card authentication
function.→p.111
“Cannot save attached file”
● This message appears when a mail is received with an
attached file that cannot be registered for Receive Ir
data, cable connection communication or copying from
microSD card.
“Cannot set this schedule”
● This message appears when you have attempted to
use “Copy & add this” on a schedule item with the
same date and time as an existing item, or if you have
received such a schedule item via infrared or iC
exchange or cable connection.
“Caution! This SMS includes Phone Nos. or
URLs. Be careful if you do not recognize the
sender.”
● This message appears when you set “Message scan”
under “Scanning function” to ON and attempt to open
SMS containing a phone number or URL. Check the
sender, then press d to display the text of the SMS.
→p.383
“Certificate is rejected (tampered)”
● This message appears when an altered SSL certificate
has been received. An SSL communication cannot be
established with this site.
● This message appears when an altered SSL/TLS
certificate has been received. An SSL/TLS
communication cannot be established with this site.
“Check new messages is set all OFF”
● New messages cannot be checked because none of
the items is selected in “Set check new messages”.
Select items to check in “Set check new messages”.
→p.179
“Connection failed”
● This message appears when the host settings are
incorrect. Set the host correctly, using “Host selection”
under i-mode common set. → p.149
● Connection to i-mode failed for some reason. Retry
connection.
● Set “Caller ID Notification” to “ON” and retry.→p.46