User's Guide Part 2

441
Appendix/External Devices/Troubleshooting
This UIM cannot be recognized
ˎ
Make sure that the correct UIM
is inserted (P.36).
ˎ
The UIM contains an error.
Contact our service counter
(DoCoMo shop, etc.).
Time out
ˎ
Failed to connect within the
time set for the Connection
timeout. Change the setting or
retry to connect after a while
(P.197).
Too many active functions.
Cannot activate
ˎ
You cannot execute the
selected function because
of too many functions being
executed by multitasking. Quit
a currently executed function
and then retry the operation
(P.353).
Too many active functions.
Cannot execute. Quit other
function and retry
ˎ
You cannot execute a selected
function because of insufficient
memory. Quit a currently
executed function and then
retry the operation (P.353).
Too much data was entered
ˎ
Failed to send because of too
many characters. Reduce the
number of characters and try
to send again.
Transmission failed
ˎ
An error occured while sending
mail. Make sure that “
” is not
displayed and send it again. If
the message appears again,
retry to send after a while
(P.213).
ˎ
The address of SMS is
incorrect. Enter the correct
address (phone number) and
send again (P.234).
Transmission failed (552)
ˎ
Failed to connect to a line due
to a problem at the i-mode or
SMS center. Retry to connect
after a while.
U
UIM is full
ˎ
The number of SMS saved
in the UIM has reached the
maximum number. Delete
unnecessary SMS (P.223).
UIM is not inserted. Content is
unavailable
ˎ
Failed to operate because the
UIM is not inserted. Insert the
UIM that was used when you
retrieved the data or file and
then retry the operation (P.36).
Unable to display this program
guide
ˎ
When 2in1 is set to the B
mode, you cannot run the
program guide i-
α
ppli with
mail or using mail.
Unable to obtain data due to
replay restriction data error
ˎ
Failed to obtain the file
because of an error in the
playback restriction data.
Unable to retrieve the
requested URL (504)
ˎ
Failed to connect to the site or
website for some reason. Retry
to connect.
Unable to run this software
ˎ
When 2in1 is set to the B
mode, you cannot run i-
α
ppli
with mail or i-
α
ppli using mail.
Unable to update pattern
definitions
ˎ
Failed to update pattern
definitions because of error
occurrence.
Unable to use in My Data B
ˎ
You cannot originate a
PushTalk call from the Own
number display of the B mode.
Unsupported microSD
ˎ
A non-compatible microSD
memory card is installed in the
FOMA terminal. Install a FOMA
terminal-compatible microSD
memory card (P.307).
URL is too long to register
ˎ
Failed to save the site as
a bookmark because the
URL exceeds 256 half-width
characters (P.191).
Usage is currently restricted.
Try again later
ˎ
Users of the flat-rate i-mode
packet service may not be
able to connect during certain
hours because of sharp
increase in communication
traffic. In this case, wait for a
while until you can use i-mode.
Use ToruCa automatic reading
func through the reader/writer?
ˎ
Auto recognition is set to [OFF]
(P.260).
Y
Your HTTP version is not
supported (505)
ˎ
You tried to connect to the site,
etc. not supporting i-mode.
Symbol
error
ˎ
An error occurred while
running the i-
α
ppli software.
Start to run again or check the
error history (P.250).
“
○
△
□
.ne.jp”
宛のメールが混み
合っているため、送信すること
ができません（
555
）
(Failed
to send mail to “
○
△
□
.ne.jp”
because the line is congested)
※
Domain names vary
depending on each recipient.
ˎ
The line is extremely
congested. Wait for a while
and then retry the operation.