User's Guide Part 1

77
PushTalk
●
Each speech session granted by obtaining the
floor is time limited. The obtained floor is released
after the time limit. The PushTalk communication
is terminated if no member takes over the floor
within a certain interval.
●
When there is any change in PushTalk
communication status or a member takes over
the floor, the signal tone sounds.
●
You cannot use i-mode during PushTalk
communication.
●
When other functions are activated, you cannot
obtain the floor. However, when you activate a
function while you have the floor, you can speak
while you press and hold .
●
When you receive a videophone call, data
communication, or a PushTalk call during
PushTalk communication, a new call is saved in
the Received record and the current PushTalk
call is continued.
Originating a PushTalk
Call

You cannot originate a PushTalk call during a voice
call, a videophone call, or data communication, or
while the B mode is set in 2in1.

If you originate a PushTalk call during i-mode
communication, the i-mode communication is
terminated. Originating a PushTalk call while running
i-
α
ppli also stops the i-
α
ppli.

Number B of 2in1 cannot be used for PushTalk and
PushTalkPlus services.
1
Enter a phone number in the stand-by
display.
2
Press .
Ｍｙｓｅｌｆ
０９０ＸＸＸＸＸＸＸＸ Ｃｏｎｎｅｃｔｅｄ
Ｏｎ ＰｕｓｈＴａｌｋ
０９０ＸＸＸＸＸＸＸＸ
Ｄｉａｌｉｎｇ ＰｕｓｈＴａｌｋ
When you originate a
PushTalk call, it is switched
to the hands-free operation
that allows you to hear the
signal tone from the speaker.
To speak
Press while the floor
is open. You can speak
while you press and hold
.
3
Press to end the communication.
●
You cannot use PushTalk to place a call to
emergency numbers (110, 119, and 118).
●
You cannot set whether to notify the caller ID
when you originate a PushTalk call even if you
add “186/184”.
●
The setting whether to originate a PushTalk call
with/without the caller ID follows the setting of the
Set Notification (P.45).
●
When you set the Set Notification to [Notify], all
members including added members are notified
the phone numbers of the person who originates
and all members. When you set it to [Not notify],
[User Unset] is displayed in the fields of the
speaker and all members including added
members.
●
If you set [Call with ID]/[Call without ID] of the
caller ID at the Option call display when you
originate a PushTalk call, the phone numbers of
yours and all members are/are not notified to all
members based on the selected call condition.
●
When you originate a PushTalk call, if the Set
Notification is set as well as the Call condition
is set at the Option call display, the following
priority is applied.
1. Call condition selected at the Option call
display when originating a PushTalk call
2. Set Notification
Originating a PushTalk Call from
the Call Record
You can originate a PushTalk call using the
Redial and Received records.

You cannot originate a PushTalk call using the call
records of Number B when 2in1 is used.
Example: Originating a PushTalk call from the Received
record
1
Press ( ) in the stand-by display.
The Received record display appears.
2
Select a received record and press .
When a PushTalk call is originated, the signal tone
sounds.
●
If a member is disconnected during PushTalk
communication among several persons, the
disconnected member can come back to the
session using the Redial/Received record as
long as the other members continue it. When the
PushTalk communication is already ended, the
call is going to be a new one.