User's Manual Part 2

398
Appendix/External Devices/Troubleshooting
This software is not supported by this
phone
ˎ
The software you want to down-
load or upgrade does not support
the FOMA terminal.
This UIM cannot be recognized
ˎ
Make sure that the correct UIM is
inserted (P.36).
ˎ
The UIM contains an error. Contact
our service counter (DoCoMo
shop, etc.).
Time out
ˎ
Failed to connect within the time
set for the Connection timeout.
Change the setting or retry to
connect after a while (P.169).
Too many active functions. Cannot
activate
ˎ
You cannot execute the selected
function because of too many
functions being executed by
multitasking. Quit a currently ex-
ecuted function and then retry the
operation (P.316).
Too many active functions. Cannot
execute. Quit other function and retry
ˎ
You cannot execute a selected
function because of insufficient
memory. Quit a currently ex-
ecuted function and then retry the
operation (P.316).
Too much data was entered
ˎ
Failed to send because of too
many characters. Reduce the
number of characters and try to
send again.
Transmission failed
ˎ
An error occured while sending
mail. Make sure that “
” is not
displayed and send it again. If the
message appears again, retry to
send after a while (P.184).
ˎ
The address of SMS is incorrect.
Enter the correct address (phone
number) and send again (P.202).
Transmission failed (552)
ˎ
Failed to connect to a line due to a
problem at the i-mode or SMS cen-
ter. Retry to connect after a while.
U
UIM is full
ˎ
The number of SMS saved in the
UIM has reached the maximum
number. Delete unnecessary SMS
(P.193).
UIM is not inserted. Content is
unavailable
ˎ
Failed to operate because the
UIM is not inserted. Insert the UIM
that was used when you retrieved
the data or file and then retry the
operation (P.36).
Unable to display this program
guide
ˎ
When 2in1 is set to the B mode,
you cannot run the program guide
i-
α
ppli with mail or using mail.
Unable to obtain data due to replay
restriction data error
ˎ
Failed to obtain the file because
of an error in the playback restric-
tion data.
Unable to retrieve the requested URL
(504)
ˎ
Failed to connect to the site or
website for some reason. Retry to
connect.
Unable to run this software
ˎ
When 2in1 is set to the B mode,
you cannot run i-
α
ppli with mail
or i-
α
ppli using mail.
Unable to search any available
channels
ˎ
Failed to search any broadcast
station in the current area.
Unable to update pattern definitions
ˎ
Failed to update pattern defini-
tions because of error occurrence.
Unable to use in My Data B
ˎ
You cannot originate a PushTalk
call from the Own number display
of the B mode.
Unavailable channel
ˎ
Failed to receive the signal be-
cause you are in a location without
the broadcast wave. Move to a lo-
cation with better radio wave con-
dition and then retry the operation.
ˎ
Failed to receive the signal because
broadcasting is in intermission.
Unsupported microSD
ˎ
A non-compatible microSD mem-
ory card is installed in the FOMA
terminal. Install a FOMA terminal-
compatible microSD memory
card (P.278).
URL is too long to register
ˎ
Failed to save the site as a book-
mark because the URL exceeds
256 half-width characters (P.164).
Usage is currently restricted. Try
again later
ˎ
Users of the flat-rate i-mode pack-
et service may not be able to con-
nect during certain hours because
of sharp increase in communica-
tion traffic. In this case, wait for a
while until you can use i-mode.
Use ToruCa automatic reading func
through the reader/writer?
ˎ
Auto recognition is set to [OFF] (P.225).
Y
Your HTTP version is not supported
(505)
ˎ
You tried to connect to the site,
etc. not supporting i-mode.
Symbol
error
ˎ
An error occurred while running the
i-
α
ppli software. Start to run again
or check the error history (P.216).
“
○
△
□
.ne.jp”
宛のメールが混み合っ
ているため、送信することができ
ません（
555
）
(Failed to send mail
to “
○
△
□
.ne.jp” because the line is
congested)
※
Domain names vary depending
on each recipient.
ˎ
The line is extremely congested.
Wait for a while and then retry the
operation.