User Manual
Table Of Contents
- 1. Introduction
- 2. GR47/GR48 Radio Devices
- 3. Abbreviations
- 4. Mechanical Description
- 5. System Connector Interface
- 5.1 Overview
- 5.2 General Electrical and Logical Characteristics
- 5.3 Grounds
- 5.4 VCC - Regulated Power Supply Input
- 5.5 Battery Charging Input (CHG_IN)
- 5.6 Turning the Radio Device ON/OFF and the External Power Signal
- 5.7 Analogue Audio
- 5.8 PCM Digital Audio
- 5.9 Serial Data Interfaces
- 5.10 SIM Card Related Signals
- 5.11 Service/Programming
- 5.12 Buzzer
- 5.13 LED
- 5.14 General Purpose Digital I/O Ports
- 5.15 Extended I/O capabilities
- 5.16 General Purpose Analogue I/O Ports
- 5.17 External I 2C Serial Control Bus
- 5.18 TX_ON - Burst Transmission
- 5.19 Real Time Clock
- 6. Antenna Connector
- 7. Keyboard Interface
- 8. Hints for Integrating the Radio Device
- 9. Embedded Applications
- 10. TCP/IP Stack
- 11. Technical Data
- 12. Declaration of Conformity
- 13. Introduction to the Developer’s Kit
- 14. Using the Developer’s Kit
14. USING THE DEVELOPER’S KIT
76
LZT 123 7589 R1A
$XGLRDQG3&0
0LVFHOODQHRXV
Jumper Default Description
ULD To OUT To enable analog audio microphone path ULD must
be connected to OUT using the jumper.
OUT To ULD To enable analog audio microphone path OUT must
be connected to ULD using the jumper.
DLD To IN To enable analog audio earpiece path DLD must be
connected to IN using the jumper.
In To DLD To enable analog audio earpiece path IN must be
connected to DLD using the jumper.
SYN - This is an output connection for the PCM
synchronisation signal from the radio device.
CLK - This is an output connection for the PCM clock signal
from the radio device.
BUZZER Fitted When fitted, this link enables the DK buzzer driver
circuitry.
Jumper Default Description
DSR Fitted Connects serial port flow control signal DSR between
UART connector X4 and radio device.
Note: DSR is a dual function signal from the radio
device. When this signal is being used for any other
purpose (e.g. Keypad or application specific through
X2 or X3), this jumper must be removed.
RI Fitted Connects serial port control signal RI between UART
connector X4 and radio device.
Note: RI is a dual function signal from the radio
device. When this signal is being used for any other
purpose (e.g. Keypad or application specific through
X2 or X3), this jumper must be removed.
DTR Fitted Connects serial port flow control signal DTR between
UART connector X4 and radio device.
Note: DTR is a dual function signal from the radio
device. When this signal is being used for any other
purpose (e.g. Keypad or application specific through
X2 or X3), this jumper must be removed.
CTS Fitted Connects serial port flow control signal CTS between
UART connector X4 and radio device.
Note: CTS is a dual function signal from the radio
device. When this signal is being used for any other
purpose (e.g. Keypad or application specific through
X2 or X3), this jumper must be removed.
RTS Fitted Connects serial port flow control signal RTS between
UART connector X4 and radio device.
Note: RTS is a dual function signal from the radio
device. When this signal is being used for any other
purpose (e.g. application specific I/O through X2 or
X3), this jumper must be removed.