User's Manual

ManualsBrandsSony Mobile Communications ManualsElectronicsTransmitter module for mobile applications

Product Photo/Illustration

GM28

Integrator’s Manual

Summary of content (264 pages)

PAGE 1
GM28 Integrator’s Manual Product Photo/Illustration
PAGE 2
SAR statement: This product is intended to be used with the antenna or other radiating element at least 20cm away from any part of the human body. The information contained in this document is the proprietary information of Sony Ericsson Mobile Communications International.
PAGE 3
Contents Part 1: Overview................................................................................................. 11 1. Introduction............................................................................................................ 13 1.1 1.2 1.3 2. GM28 Modem......................................................................................................... 14 2.1 2.2 2.3 2.4 2.5 2.6 3. Target Users ................................................................................
PAGE 4
GM28 INTEGRATOR’S MANUAL 3.1 3.2 3.3 3.4 4. Hints for Integrating the Modem..........................................................................38 4.1 4.2 4.3 4.4 5. Switching On the Modem............................................................................. 36 Switching Off the Modem ............................................................................ 36 Resetting the Modem.................................................................................... 36 Operating States/LED.
PAGE 5
2.12 AT+VTS 3. Control and Status ................................................................................................. 67 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 3.29 4. ATQ ATS0 ATS2 ATS3 ATS4 ATS5 ATS6 ATS7 ATS8 ATS10 AT*ECAM AT*EDST AT*EMAR AT*EPEE AT+CCLK AT+CEER AT+CFUN AT+CIND AT+CLAC AT+CMEE AT+CMER AT+CPAS AT+CPIN AT+CPWD AT+CR AT+CRC AT+CSAS AT+CSQ AT+CTZU Result Code Suppression ............
PAGE 6
GM28 INTEGRATOR’S MANUAL 6. Data - GPRS..........................................................................................................107 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 7. AT+CHSC AT+CHSD AT+CHSN AT+CHSR AT+CHSU HSCSD Current Call Parameters ................................... 121 HSCSD Device Parameters............................................ 122 HSCSD Non Transparent Call Configuration................ 123 HSCSD Parameters Report ............................................
PAGE 7
10.12 10.13 10.14 10.15 AT+IFC AT+ILRR AT+IPR AT*E2ESC DTE-DCE Local Flow Control...................................... Cable Interface Local Rate Reporting ........................... Cable Interface Port Command ..................................... M2M Escape Sequence Guard Time ............................. 140 141 141 142 11. Network................................................................................................................. 143 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 11.
PAGE 8
GM28 INTEGRATOR’S MANUAL 13.9 13.10 13.11 13.12 13.13 13.14 13.15 13.16 13.17 AT+CMGC AT+CNMI AT+CMGR AT+CMGL AT+CMGD AT+CSDH AT+CSMP AT+CSCS AT+CSMS Send Command .............................................................. 189 New Message Indications to TE .................................... 192 Read Message................................................................. 196 List Message................................................................... 201 Delete Message ...........................
PAGE 9
17. Alphabetical Listing of AT Commands .............................................................
PAGE 10
GM28 INTEGRATOR’S MANUAL 10 LZT 123 7468 P1A
PAGE 11
Part 1: Overview Product Photo/Illustration
PAGE 12
PAGE 13
1. Introduction 1.1 Target Users GM28 modems are designed to be integrated into machine-machine or man-to-machine communications applications. They are intended to be used by manufacturers, system integrators, applications developers and developers of wireless communications equipment. 1.
PAGE 14
GM28 INTEGRATOR’S MANUAL 2. GM28 Modem 2.1 Description The dual band GSM 850/1900MHz GM28 is a GSM/GPRS serial modem. The modem is a powerful and flexible device that can be used in a wide range of telemetry and telematics applications that rely on the remote exchange of data, voice, SMS or faxes via the GSM cellular network. Small and lightweight, the GM28 has standard connectors and an integral SIM card reader making it easy and quick to integrate.
PAGE 15
2. GM28 MODEM 2.3 GM28 in a Communication System Figure 2.1 illustrates the main blocks of a wireless communication system using the GM28. It also shows the communication principles of the system. The definitions in the figure, as used elsewhere in this manual, are in accordance with the recommendations of GSM 07.07. • The MS (mobile station) represents the GM28 modem plus SIM card. The modem excluding SIM card, is known as the ME (mobile equipment). • The TE (terminal equipment) is a micro-controller (i.
PAGE 16
GM28 INTEGRATOR’S MANUAL Figure 2.2 illustrates the interface between the modem and the application. The entire System Connector Interface is described in detail in “Electrical Description”, page 28. Power and signals RJ11 Audio RJ9 Serial data TE (Application) MS (GM28) Antenna connector DB9 Figure 2.2 The Interface between the modem and the Application Note! ITU-T standards define TE and TA as DTE (Data Terminal Equipment) and DCE (Data Circuit Terminating Equipment) respectively.
PAGE 17
2. GM28 MODEM 2.4 Main Features and Services The modem performs a set of telecom services (TS) according to GSM standard phase 2+, ETSI and ITU-T. The services and functions of the modem are implemented by issuing AT commands over the RS232 serial interface. 2.4.1 Types of Mobile Station The GM28 is a dual band serial modem with the GSM radio characteristics shown in the table below.
PAGE 18
GM28 INTEGRATOR’S MANUAL 2.4.3 Voice Calls The GM28 offers the capability of mobile originated and mobile terminated voice calls, as well as supporting emergency calls. Multi-party, call waiting and call deflection features are available. Some of these features are network-operator specific. For the inter-connection of audio, the modem offers a balanced 4-wire analogue interface. DTMF (Dual Tone Multi Frequency) is supported. 2.4.
PAGE 19
2. GM28 MODEM • Network registration • Call barring • Call transfer 2.4.7 Serial Communication The GM28 enables an end-to-end communication path to be established between the external telemetry/telematics application and a remote terminal or host, via the GSM network. Once a path has been set up, voice or data communication can take place. Serial data with flow control according to the RS232 signalling protocol operates between the modem and the external application.
PAGE 20
GM28 INTEGRATOR’S MANUAL 2.5 Service and Support To contact customer support please use the details below: Customer Support Sony Ericsson Mobile Communications Maplewood Building Chineham Business Park Basingstoke RG24 8YB E-mail: modules.support@sonyericsson.com or modules.info@sonyericsson.com Information about Sony Ericsson and its products is available on the following web site: http://www.sonyericsson.com/M2M 2.6 Precautions The GM28 as a stand alone item is designed for indoor use only.
PAGE 21
3. ABBREVIATIONS 3.
PAGE 22
GM28 INTEGRATOR’S MANUAL Abbreviation Explanations SMS Short Message Service TA Terminal Adapter TE Terminal Equipment TS Telecom Services 22 LZT 123 7468 P1A
PAGE 23
Part 2: Integrating the Modem Product Photo/Illustration
PAGE 24
PAGE 25
1. Mechanical Description 1.1 Overview The pictures below show the mechanical design of the GM28 along with the positions of the different connectors and mounting holes. The GM28 case is made of durable PC/ABS plastic. LED Antenna connector RS232 connector Access to SIM card Figure 1.1 GM28 viewed from the left side Mounting hole (x2) Audio connector Power connector Figure 1.
PAGE 26
GM28 INTEGRATOR’S MANUAL Please note the following: • Mounting holes positioned at two of the corners make it possible to securely bolt the modem into your application. • Keypad, display, microphone, speaker and battery are not part of the modem. • The SIM card is mounted in the modem. • The pins and electrical characteristics or the modem’s various connectors are described in “2. Electrical Description”, page 28. • Information about the antenna connector is found in “2.3 Antenna Connector”, page 31.
PAGE 27
1. MECHANICAL DESCRIPTION 1.2 Physical Dimensions 3.5 71 51.0 66.4 .5 2) 45.3 (x 9.0 26.2 55.3 10.6 11.0 11.0 77.4 Measurements are given in millimetres. See also “Technical Data”, page 44.
PAGE 28
GM28 INTEGRATOR’S MANUAL 2. Electrical Description All electrical connections to the GM28 are designed to meet the standard air (4kV) and contact (8kV) discharge ESD tests, of EN 301 489-1. The modem uses the following industry standard connectors: • RJ11 6-way (power connector) • RJ9 4-way (handset connector) • SIM card reader • FME male coaxial jack (antenna connector) • Sub-D socket, 9 pin (RS232 serial port) 2.
PAGE 29
2. ELECTRICAL DESCRIPTION The power connector electrical characteristics are listed below: Pin Signal Dir Limits Description 1 VCC I 5 - 32V Positive power input 2 - - - No connection 3 HR_IN I –0.5 - 32V Active high control line used to switch off or reset the modem VIH > 5V, VIL < 2V Power off: 1s < t < 2s Hard reset: t > 3.5s 4 TO_IN I –0.5 - 32V Active high control line used to switch on the modem VIH > 5V, VIL < 2V Power on: t > 0.
PAGE 30
GM28 INTEGRATOR’S MANUAL Audio signal descriptions are listed below: Pin Signal Dir Description 1 MICN I Microphone negative input 2 BEARN O Earpiece negative output 3 BEARP O Earpiece positive output 4 MICP I Microphone positive input MICP and MICN are balanced differential microphone input signals. These inputs are compatible with an electret microphone. BEARP and BEARN are the speaker output signals. These are differential-mode outputs.
PAGE 31
2. ELECTRICAL DESCRIPTION 2.3 Antenna Connector The antenna connector allows transmission of radio frequency (RF) signals between the modem and an external customer-supplied antenna. The modem is fitted with a 50: FME male coaxial jack as shown below. RF Signal GND The table below shows the antenna electrical characteristics: Parameter Limit Nominal impedance 50: (SWR better than 2.
PAGE 32
GM28 INTEGRATOR’S MANUAL 2.4 SIM Card Reader The GM28 is fitted with a SIM card reader designed for 3V and 5V SIM cards. It is the flip-up type which is lockable in the horizontal position and is accessed through a removable panel as shown below. The SIM card reader includes a SIM presence switch. This ensures that when a SIM card is inserted or removed while the GM28 is turned ON, it will reset.
PAGE 33
2. ELECTRICAL DESCRIPTION 2.5 RS232 Serial Port The modem supports a standard RS232 serial interface (EIA/TIA 574) via its 9 pin Sub-D connector, shown below. In line with serial communication terminology the GM28 serial modem should be considered as the data circuit-terminating equipment (DCE) and the external application or computer as the data terminating equipment (DTE).
PAGE 34
GM28 INTEGRATOR’S MANUAL 2.5.1 Serial Data The modem supports the standard data character format of 1 start bit, 8 bit data, no parity plus 1 stop bit, in total 10 bits per character. 2.5.2 Serial Data Signals - RD, TD The default baud rate is 9.6kbps, however higher bit rates up to 460kbps are supported. At start-up the GM28 transmits and receives data at the default rate of 9.6kbps in either standard AT mode or binary mode (the first received data - AT or binary format - determines the operating mode).
PAGE 35
2. ELECTRICAL DESCRIPTION Data Terminal Ready (DTR) DTR indicates that the DTE is ready to transmit and receive data. It also acts as a hardware ‘hang-up’, terminating calls when switched high. The signal is active low. You can define the exact behaviour of DTR with an AT command. The DTR line can also be used to switch on the modem when activated for 0.2 seconds. The DTR line must be deactivated prior to switching off the modem to ensure it switches off (powers down) correctly.
PAGE 36
GM28 INTEGRATOR’S MANUAL 3. Operation 3.1 Switching On the Modem There are two ways to switch on the modem, once power is applied. • either assert TO_IN high for > 0.2s; • or activate the RS232 control line DTR, high for > 0.2s. The modem is fully operational after 4 seconds. Logging onto a network may take longer than this and is outside the control of the modem.
PAGE 37
3. OPERATION 3.4 Operating States/LED The modem has a green LED, as depicted below, which is used to indicate various operating states. These states are described in following table. LED Notes! Operating State LED Status After switching on the modem On after 4s Switch off (Power down) or power removed Off Standby or talk Flashing No network, network search, no SIM card, no PIN entered On Switch off (Power Down): DC power is applied but the modem is switched OFF.
PAGE 38
GM28 INTEGRATOR’S MANUAL 4. Hints for Integrating the Modem This chapter gives you advice and helpful hints on how to integrate the GM28 into your application from a hardware perspective. Please read and consider the information under the following headings before starting your integration work: • Safety advice and precautions. • Installation of the modem. • Antenna. 4.1 Safety Advice and Precautions 4.1.1 General • Always ensure that use of the modem is permitted.
PAGE 39
4. HINTS FOR INTEGRATING THE MODEM • When the SIM card hatch is opened, the SIM card connectors lie exposed under the SIM card holder. CAUTION: Do not touch these connectors! If you do, you may release an electrical discharge that could damage the modem or the SIM card. • When designing your application, the SIM card’s accessibility should be taken into account. We always recommend that you have the SIM card protected by a PIN code.
PAGE 40
GM28 INTEGRATOR’S MANUAL Environmental Conditions The modem must be installed so that the environmental conditions stated in the Technical Data chapter, such as temperature, humidity and vibration are satisfied. Additionally, the electrical specifications in the Technical Data section must not be exceeded. Signal Strength The modem has to be placed in a way that ensures sufficient signal strength. To improve signal strength, the antenna can be moved to another position.
PAGE 41
4. HINTS FOR INTEGRATING THE MODEM 4.2.2 How to Install the Modem Power Supply • Use a high-quality power supply cable with low resistance. This ensures that the voltages at the connector pins are within the allowed range, even during the maximum peak current. • When the unit is powered from a battery or a high current supply, connect a fast 1.25A fuse in line with the positive supply. This protects the power cabling and modem.
PAGE 42
GM28 INTEGRATOR’S MANUAL • communication disturbances in the vicinity in which the antenna operates. In the sections below, issues concerning antenna type, antenna placement, antenna cable, and possible communication disturbances are addressed. In any event, you should contact your local antenna manufacturer for additional information concerning antenna type, cables, connectors, antenna placement, and the surrounding area. You should also determine whether the antenna needs to be grounded or not.
PAGE 43
4. HINTS FOR INTEGRATING THE MODEM Minimize the use of extension cables, connectors and adapters. Each additional cable, connector or adapter causes a loss of signal power. 4.3.5 Possible Communication Disturbances Possible communication disturbances include the following: • Noise can be caused by electronic devices and radio transmitters. • Path-loss occurs as the strength of the received signal steadily decreases in proportion to the distance from the transmitter.
PAGE 44
GM28 INTEGRATOR’S MANUAL 5. Technical Data Data Features CSD Up to 9.6kbps HSCSD (2+1) Up to 19.2kbps GPRS Class B (4+1) - P channels - Coding schemes CS1 - CS4 85.6kbps (subject to network support and terminal location) GSM 07.
PAGE 45
5. TECHNICAL DATA Data Storage SMS storage capacity 40 in ME In addition, the unit can handle as many SMS as the SIM can store Phone book capacity 100 Power Supply Supply voltage range 5 - 32V d.c.
PAGE 46
GM28 INTEGRATOR’S MANUAL The power consumption in Standby Mode is measured at the maximum paging rate. Radio Specifications Frequency range GM28: GSM 850MHz and 1900MHz (dual band) Maximum RF output power 2W (850MHz) and 1W (1900MHz) Antenna impedance 50: Static sensitivity Better than –102dBm E-OTD Currently unsupported in GM28 Audio Specifications Parameter Limit Output level (differential) t 4.0Vpp Output level (dynamic load = 32:) t 2.
PAGE 47
5. TECHNICAL DATA Electrical Connectors and LED Plug-in power supply connector RJ11 6-way Handset audio connector RJ9 4-way Antenna connector FME male RS232 port Sub-D socket, 9 pin LED Green Mechanical Specification Length 77.4mm Width 66.4mm Height 26.
PAGE 48
GM28 INTEGRATOR’S MANUAL Environmental specifications Operating temperature range –25°C to +55°C Storage temperature range –40°C to +85°C Relative humidity 5 - 95%, non-condensing Stationary vibration, sinusoidal Displacement: 7.5mm Acceleration amplitude: 20m/s² and 40m/s² Frequency range: 2-8Hz, 8-200Hz, 200-500Hz Stationary vibration, random Acceleration spectral density (m²/s²): 0.96, 2.88, 0.
PAGE 49
Part 3: Using AT Commands Product Photo/Illustration
PAGE 50
PAGE 51
1. Introduction to AT Commands 1.1 Overview AT commands, issued from a computer in your application are used to control and implement the functions of the modem. Using AT commands, the following actions are possible: • Control of DCE • GPRS • Call control • Supplementary Service • SIM application tool kit The GM28 contains a large number of Ericsson-specific commands in addition to those implemented in accordance with the GSM and ITU-T recommendations.
PAGE 52
GM28 INTEGRATOR’S MANUAL [] Square brackets are used to indicate that a certain item is optional. For example, sub-parameters of a command or an optional part of a response. The brackets do not appear in the command line. The default values of the supported parameters are indicated by using bold text when presenting the value. • Other characters, including ‘?’, ‘ ’, parenthesis, etc., appear in commands and responses as written.
PAGE 53
1. INTRODUCTION TO AT COMMANDS • AT*=[] Example! AT+CFUN=0 (powers down the modem) If several values are included in the command, they are separated by commas. It is also possible to enter commands with no values. Additional commands may follow an extended syntax command on the same command line if a semicolon (; IRA 3B) is inserted after the preceeding extended command as a separator. Read Command Syntax The read command is used to check the current values of parameters.
PAGE 54
GM28 INTEGRATOR’S MANUAL Possible formats for the result codes are: • Basic format result code, such as OK. The Basic result code also has a numerical equivalent.
PAGE 55
1. INTRODUCTION TO AT COMMANDS 1.3 Error Codes 1.3.1 +CME ERROR (Mobile Equipment Error Code) This final result code is similar to the regular ERROR result code. If +CME ERROR: is the result code for any of the commands in a command line, none of the commands in the same command line will be executed (neither ERROR nor OK result code shall be returned as a result of a completed command line execution). The format of can be either numerical or alphabetical, and is set with the +CMEE command.
PAGE 56
GM28 INTEGRATOR’S MANUAL Description Syntax 31 Network time-out 32 Network not allowed - emergency calls only 100 Unknown 101- 255 Reserved by ETS 1.3.2 +CMS ERROR (Message Service Failure Result Code) This final result code indicates an error related to mobile equipment or to the network. The operation is similar to the ERROR result code. None of the following commands in the same command line will be executed. Neither ERROR nor OK result code will be returned.
PAGE 57
1. INTRODUCTION TO AT COMMANDS Description 321 Invalid memory index 322 Memory full 330 SMSC address unknown 331 No network service 332 Network time-out 340 No +CNMA acknowledgment expected 500 Unknown error - 511 Other values in range 256 - 511 are reserved 512- Manufacturer specific 1.4 Examples on How to Use the AT Commands After every group of AT commands there is a section where some of the more complicated commands are exemplified.
PAGE 58
GM28 INTEGRATOR’S MANUAL 58 LZT 123 7468 P1A
PAGE 59
2. Call Control 2.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 2.2 ATA Answer Incoming Call Description Command Possible Responses Answer an incoming call ATA • • • • • CONNECT CONNECT NO CARRIER ERROR OK Answer and initiate connection to an incoming call.
PAGE 60
GM28 INTEGRATOR’S MANUAL 2.
PAGE 61
2. CALL CONTROL transmitted during the first 125 milliseconds after transmission of the termination character are ignored. This is to allow the DTE to append additional control characters such as line feed after the command line termination character.
PAGE 62
GM28 INTEGRATOR’S MANUAL 2.4 ATH Hang up Description Command Possible Responses Terminate the call ATH • ERROR • OK Signals the MS to terminate an active call. 2.5 ATO Return to Online Data Mode Description Command Possible Responses Return to on-line data mode ATO[] • • • • CONNECT CONNECT NO CARRIER ERROR Switch to the on-line data mode from the on-line command mode during an active call. Returns ERROR when not in on-line command mode. 2.
PAGE 63
2. CALL CONTROL 2.8 ATX Call Progress Monitoring Control Description Command Possible Responses Set call progress monitoring control ATX=[] or ATX[] • OK • ERROR Read the current setting ATX? X: Show if the command is supported? ATX=? X: (list of supported s) Defines if the dial-tone detection and busy-tone detection are to be used during a call set-up. Note! 2.9 AT+CHUP Description 0 Body and dial tone detection off.
PAGE 64
GM28 INTEGRATOR’S MANUAL 2.10 AT+CMOD Call Mode Description Command Possible Responses Request Call Mode AT+CMOD=[] • OK • ERROR Shows the current setting AT+CMOD? • +CMOD: • OK • ERROR Show if the command is supported AT+CMOD=? • +CMOD: (list of supported s) • OK • ERROR Selects the call mode of further dialing commands (D) or for next answering command (A). Mode can be either single or alternating.
PAGE 65
2. CALL CONTROL 2.11 AT+CVHU Voice Hang-Up Description Command Possible Responses Set Command +CVHU=[] • +CME ERROR: • OK Read command +CVHU? • +CVHU: • +CME ERROR: Test if the command is supported +CVHU=? +CVHU: (list of supported s) Selects whether ATH or “drop DTR” causes a voice connection to be disconnected or not. Voice connection also includes alternating mode calls that are currently in voice mode. Note! 2.
PAGE 66
GM28 INTEGRATOR’S MANUAL Note! The AT+VTS command is used only during a voice call. Description ASCII character string An ASCII character string with entries in the set 0-9, #, *, AD separated by commas. Each entry is interpreted as a single ASCII character.
PAGE 67
3. Control and Status 3.1 ATQ Result Code Suppression Description Command Possible Responses Set Result Code Suppression ATQ[=] • OK • ERROR Read the current setting ATQ? Q: Show if the command is supported ATQ=? Q: (list of supported s) Determines whether or not the DCE transmits result codes to the DTE.
PAGE 68
GM28 INTEGRATOR’S MANUAL 3.3 ATS2 Escape Sequence Character Description Command Possible Responses Set escape sequence character ATS2=[] • OK • ERROR Read the current setting ATS2 Show if the command is supported ATS2=? S2: (list of supported s) Defines the character to be used as the escape sequence character when switching from on-line data mode to on-line command mode. The response to the command is modified to reflect the change. Note! 3.
PAGE 69
3. CONTROL AND STATUS the command line is terminated with a character (IA5 0/13), but the result code issued uses the character with the ordinal value 30 (IA5 2/14) in place of the . 3.
PAGE 70
GM28 INTEGRATOR’S MANUAL 3.6 ATS5 Command Line Editing Character (BACKSPACE) Description Command Possible Responses Request Command Line Editing Character ATS5= • OK • ERROR Shows the current setting ATS5? Show if the command is supported ATS5=? S5: (list of supported s) This S-parameter represents the decimal IA5 value of the character recognised by the DCE as a request to delete from the command line the immediately preceding character. 3.
PAGE 71
3. CONTROL AND STATUS 3.8 ATS7 Connection Completion Timeout Description Command Possible Responses Set connection completion timeout ATS7=[] • OK • ERROR Read the current setting ATS7? Show if the command is supported ATS7=? S7: (list of supported s) Defines the maximum time allowed between completion of dialling and the connection being established. If this time is exceeded then the connection is aborted. 3.9 ATS8 Description 50 Timeout value in seconds.
PAGE 72
GM28 INTEGRATOR’S MANUAL 3.10 ATS10 Automatic Disconnect Delay Control Description Command Possible Responses Set Automatic Disconnect Delay Control ATS10=[] • OK • ERROR Read the current setting ATS10? Show if the command is supported ATS10=? S10: (list of supported s) Included for compatibility. No functionality 3.11 AT*ECAM Description 2 Remains connected for two tenths of a second.
PAGE 73
3. CONTROL AND STATUS • to make it possible for the TE to display call state information for an ongoing call. Description 0 The call log function is disabled (off). Default value 1 The call log function is enabled (on) Examples AT*ECAM? *ECAM: 0 AT*ECAM=1 OK 3.
PAGE 74
GM28 INTEGRATOR’S MANUAL 3.13 AT*EMAR Ericsson Master Reset Description Command Possible Responses Perform a master reset in the MS AT*EMAR= • +CME ERROR: • OK • ERROR Shows if the command is supported or not AT*EMAR=? • +CME ERROR: • OK • ERROR This command requests the MS to reset user data. The user data in the MS will be reset to the default values. This command also unlocks the MS. 3.
PAGE 75
3. CONTROL AND STATUS 3.15 AT+CCLK Set Clock and Date Description Command Possible Responses Set the real time clock of the ME AT+CCLK= • +CME ERROR: • OK • ERROR Show the current setting AT+CCLK? • • • • Show if the command is supported AT+CCLK=? • OK • ERROR +CCLK: +CME ERROR: OK ERROR Sets the real time clock of the ME. If setting fails in an ME, error +CME ERROR: is returned. Read command returns the current setting of the clock.
PAGE 76
GM28 INTEGRATOR’S MANUAL 3.17 AT+CFUN Set Phone Functionality Description Command Possible Responses Set MS functionality AT+CFUN= • +CME ERROR: • OK Show the current setting AT+CFUN? • +CFUN: • +CME ERROR: Show if the command is supported AT+CFUN=? • +CFUN: (list of supported s) • +CME ERROR: Selects the level of functionality in the MS. "Full functionality" results in the highest level of power usage. It is possible to activate all parts of the modem.
PAGE 77
3. CONTROL AND STATUS 3.18 AT+CIND Indicator Control Description Command Possible Responses Set Indicator Control AT+CIND=[ [,[,…]]] • +CME ERROR: • OK • ERROR Read the current setting AT+CIND? • • • • Test if the command is supported AT+CIND=? • +CIND: (,(list of supported s)), (,(list of supported s)),… • +CME ERROR: • OK • ERROR +CIND: ,,… +CME ERROR: OK ERROR Used to set the values of ME indicators.
PAGE 78
GM28 INTEGRATOR’S MANUAL 3.19 AT+CLAC List all available AT Commands Command Possible Responses +CLAC [ […]] +CME ERROR: +CLAC=? +CME ERROR: Causes the ME to return one or more lines of AT commands. This command has the same functionality as AT*. Note! 3.20 AT+CMEE This command only returns the AT commands that are available to the user.
PAGE 79
3. CONTROL AND STATUS 3.
PAGE 80
GM28 INTEGRATOR’S MANUAL 3.22 AT+CPAS Phone Activity Status Description Command Possible Responses Execute Phone Activity Status AT+CPAS[=] • • • • Test if the command is supported AT+CPAS=? • +CPAS: (list of supported s) • +CME ERROR • OK • ERROR +CPAS: +CME ERROR OK ERROR Returns the activity status of the ME. It can be used to interrogate the ME before requesting action from the phone.
PAGE 81
3. CONTROL AND STATUS 3.23 AT+CPIN PIN Control Description Command Possible Responses Request PIN Control AT+CPIN=[,] • +CME ERROR: • OK • ERROR Show the current setting AT+CPIN? • +CPIN: • +CME ERROR: • OK • ERROR Show if the command is supported AT+CPIN=? • +CME ERROR: • +CPIN: (supported s) • OK • ERROR Sends the password to the ME, which is necessary to make the ME operational (SIM PIN, SIM PUK or PH-SIM).
PAGE 82
GM28 INTEGRATOR’S MANUAL Description PH-SIM PIN ME is waiting PHone-to-SIM card password to be given SIM PIN2 ME is waiting SIM PIN2 to be given. This is recommended to be returned only when the last executed command resulted in PIN2 authentication failure (i.e. +CME ERROR: 17); if PIN2 is not entered correctly after the failure, it is recommended that ME does not block its operation SIM PUK2 ME is waiting SIM PUK2 to be given.
PAGE 83
3. CONTROL AND STATUS 3.24 AT+CPWD Change Password Description Command Possible Responses Request facility lock AT+CPWD=, , • +CME ERROR • OK • ERROR Show if the command is supported AT+CPWD=? • +CPWD: (,), (,), … • +CME ERROR • OK • ERROR Sets a new password for the facility lock function defined by command Facility Lock +CLCK.
PAGE 84
GM28 INTEGRATOR’S MANUAL Description Integer type Maximum length of the password for the facility Description 0 Phone failure 3 Operation not allowed 5 PH-SIM PIN required 10 SIM not inserted 11 SIM PIN required 12 SIM PUK required 13 SIM failure 14 SIM busy 15 SIM wrong 16 Incorrect password 17 SIM PIN2 required 18 SIM PUK2 required 23 Text string too long 24 Invalid characters in text string 100 Unknown 101..
PAGE 85
3. CONTROL AND STATUS 3.25 AT+CR Service Reporting Control Description Command Possible Responses Set Service Reporting Control AT+CR= • OK • ERROR Read current setting AT+CR? • +CR: • OK • ERROR Test if the command is supported AT+CR=? • +CR: (list of supported s) • OK • ERROR Enables or disables display of intermediate bearer capability reports during the handshake phase. Description 0 Disable reporting.
PAGE 86
GM28 INTEGRATOR’S MANUAL Test command returns values supported by the TA as a compound value. Description 0 Disables extended format 1 Enables extended format Unsolicited Result Codes: +CRING: 3.
PAGE 87
3. CONTROL AND STATUS 3.28 AT+CSQ Signal Strength Description Command Possible Responses Execute Signal Strength AT+CSQ • • • • Test if the command is supported AT+CSQ=? • +CSQ: (list of supported s),(list of supported s) • +CME ERROR • OK • ERROR +CSQ: , +CME ERROR OK ERROR Returns the received signal strength indication and channel bit error rate from the ME. Test command returns values supported by the TA as compound values.
PAGE 88
GM28 INTEGRATOR’S MANUAL 3.29 AT+CTZU Automatic Time Zone Update Description Command Possible Responses Enable and disable automatic time zone update via NITZ AT+CTZU= • +CME ERROR: • OK • ERROR Read current setting AT+CTZU? • • • • Show if the command is supported AT+CTZU=? • +CTZU: (list of supported s) • +CME ERROR: • OK • ERROR +CTZU: +CME ERROR: OK ERROR Enables and disables the automatic time zone update via NITZ.
PAGE 89
4. Audio AT*E2EAMS and AT*E2APR are new commands that replace the funtionality offered by the *EALR, *EAMS, *EARS and *ELAM commands. Use the new commands in new applications. The old commands are included for compatibility. 4.
PAGE 90
GM28 INTEGRATOR’S MANUAL • configure the whole profile, specifying each audio parameter in a comma separated list; • set a single parameter, given by its parameter number; • save the current profile to non-volatile memory under the current profile number (see AT*E2APR). The current audio settings can also be displayed by running the read command AT*E2EAMS? Default audio settings are given in AT*E2APR. Abortability: This command may not be aborted.
PAGE 91
4.
PAGE 92
GM28 INTEGRATOR’S MANUAL , Description 4 5dB PGA gain 5 7.5dB PGA gain 6 –7.
PAGE 93
4.
PAGE 94
GM28 INTEGRATOR’S MANUAL Description 0 Microphone voltage at 2.
PAGE 95
4. AUDIO 4.
PAGE 96
GM28 INTEGRATOR’S MANUAL , Description 0 Profile 0 (Factory profile set for handset).
PAGE 97
4. AUDIO 4.3 AT*EALR Ericsson Audio Line Request Description Command Possible Responses Request the audio lines (ATMS,AFMS) AT*EALR= [, [,]] • *EALR: , , • OK • ERROR Show the current setting AT*EALR? *EALR: ,, Show list of supported parameters AT*EALR=? *EALR:(list of supported s, s and s parameters) Included for compatibility. No functionality.
PAGE 98
GM28 INTEGRATOR’S MANUAL 4.
PAGE 99
4. AUDIO 4.
PAGE 100
GM28 INTEGRATOR’S MANUAL 4.6 AT*ELAM Ericsson Local Audio Mode Description Command Possible Responses Set local audio mode AT*ELAM= [,] • *ELAM: , • OK • ERROR Show the current service setting AT*ELAM? *ELAM: , Show list of supported parameters AT*ELAM=? *ELAM: (list of supported s and s parameters) Included for compatibility. No functionality. 4.
PAGE 101
4. AUDIO 4.8 AT*EMIR Ericsson Music Mute Indication Request Description Command Possible Responses Request for mute indications AT*EMIR= • OK • ERROR Show supported message types along with the current service setting AT*EMIR? *EMIR: , Show list of supported services AT*EMIR=? *EMIR: (list of supported s) Included for compatibility. No functionality. 4.
PAGE 102
GM28 INTEGRATOR’S MANUAL The set command is effective only as long as the phone senses that it is connected to an external accessory that has issued the command. Once the phone and the accessory are disconnected the setting returns to default. Description 0 The phone MMI controls audio volume over AFMS 1 Audio volume over AFMS is output at maximum level that is no clipping occurs.
PAGE 103
5. Data - CSD/HSCSD Note! Since the modem does not support V42bis compression the following commands have not been implemented: • AT+DS • AT+DR 5.
PAGE 104
GM28 INTEGRATOR’S MANUAL Description 71 9600bps V.110 (ISDN) 75 14400bps V.110 (ISDN) 79 19200bps V.110 (ISDN) 80 28800bps V.110 (ISDN) 81 38400bps V.110 (ISDN) 82 48000bps V.110 (ISDN) 83 56000bps V.110 (ISDN) Description 0 Asynchronous connection (UDI or 3.
PAGE 105
5. DATA - CSD/HSCSD 5.2 AT+CRLP Radio Link Protocol Description Command Possible Responses Set radio link protocol AT+CRLP=[ [,[, [,[, [, ]]]]]] • OK • ERROR Read the command AT+CRLP? • +CRLP: ,,,[, [,]][ • +CRLP: ,,,[, [,]][...
PAGE 106
GM28 INTEGRATOR’S MANUAL Description 48 38 - 100 Acknowledgment timer T1 (*10ms) Description 6 0 - 255 Re-transmission attempts N2 Description 5 3 - 255 Re-sequencing period T4 (*10ms) Description Integer RLP version.
PAGE 107
6. Data - GPRS 6.1 AT+CGACT PDP Context Activate or Deactivate Description Command Possible Responses Activate or deactivate the specified PDP context(s) +CGACT=[ [,[,[,…]]]] • +CME ERROR: • OK • ERROR Read the command +CGACT? • +CGACT: , [ +CGACT: , [...]] • OK • ERROR Test if the command is supported +CGACT=? • +CGACT: (list of supported s) • OK • ERROR Used to activate or deactivate the specified PDP context(s).
PAGE 108
GM28 INTEGRATOR’S MANUAL 6.2 AT+CGATT GPRS Attach or Detach Description Command Possible Responses Attach or detach MS to the GPRS/packet domain/packet domain service +CGATT=[] • +CME ERROR: • OK • ERROR Read the command +CGATT? • +CGATT: • OK • ERROR Test if the command is supported +CGATT=? • +CGATT: (list of supported s) • OK • ERROR Used to attach the MS to, or detach the MS from, the GPRS/packet domain service.
PAGE 109
6. DATA - GPRS 6.3 AT+CGDATA Enter Data State Description Command Possible Responses Establish GPRS/packet domain connection +CGDATA=[,[cid [,cid>[,…]]]] • • • • Test if the command is supported +CGDATA=? • +CGDATA: (list of supported s) • OK • ERROR CONNECT ERROR OK ERROR Causes the MS to perform whatever actions are necessary to establish communication between the TE and the network using one or more GPRS/packet domain PDP types.
PAGE 110
GM28 INTEGRATOR’S MANUAL 6.4 AT+CGDCONT Define PDP Context Description Command Possible Responses Select PDP context parameters +CGDCONT=[ [, [, [, [, [, [, [,…[,pdN]]]]]]]]] • +CME ERROR: • OK • ERROR Read the command +CGDCONT? • +CGDCONT: , ,, ,, [,[,…[,pdN]]] [+CGDCONT: , ,, ,, [,[,…[,pdN]]] [...
PAGE 111
6. DATA - GPRS Description String type (Access Point Name) a string parameter which is a logical name that is used to select the GGSN or the external packet data network. If the value is null or omitted, then the subscription value will be requested Description String type A string parameter that identifies the MS in the address space applicable to the PDP.
PAGE 112
GM28 INTEGRATOR’S MANUAL 6.
PAGE 113
6. DATA - GPRS 6.6 AT+CGPADDR Show PDP Address Description Command Possible Responses Show PDP addresses for specified CIDs +CGPADDR=[ [, [,…]]] • +CGPADDR: , [+CGPAD DR: , [...]] • OK • ERROR Test if the command is supported +CGPADDR=? • +CGPADDR: (list of defined s) • OK • ERROR Returns a list of PDP addresses for the specified context identifiers. The test command returns a list of defined s.
PAGE 114
GM28 INTEGRATOR’S MANUAL 6.
PAGE 115
6.
PAGE 116
GM28 INTEGRATOR’S MANUAL 6.8 AT+CGQREQ Description 8 10000 (~22bits/s) 9 20000 (~44bits/s) 10 50000 (~111bits/s) 11 100000 (~0.22kbits/s) 12 200000 (~0.44kbits/s) 13 500000 (~1.11kbits/s) 14 1000000 (~2.2kbits/s) 15 2000000 (~4.4kbits/s) 16 5000000 (~11.
PAGE 117
6. DATA - GPRS The set command specifies a profile for the context identified by the (local) context identification parameter, . Since this is the same parameter that is used in the +CGDCONT command, the +CGQREQ command is effectively an extension to the +CGDCONT command. The QoS profile consists of a number of parameters, each of which may be set to a separate value. A special form of the set command, +CGQREQ= causes the requested profile for context number to become undefined.
PAGE 118
GM28 INTEGRATOR’S MANUAL Description 0 Subscribed (from network) value used 1 Best effort 2 100 (~0.22bits/s) 3 200 (~0.44bits/s) 4 500 (~1.11bits/s) 5 1000 (~2.2bits/s) 6 2000 (~4.4bits/s) 7 5000 (~11.1bits/s) 8 10000 (~22bits/s) 9 20000 (~44bits/s) 10 50000 (~111bits/s) 11 100000 (~0.22kbits/s) 12 200000 (~0.44kbits/s) 13 500000 (~1.11kbits/s) 14 1000000 (~2.2kbits/s) 15 2000000 (~4.4kbits/s) 16 5000000 (~11.
PAGE 119
6. DATA - GPRS 6.
PAGE 120
GM28 INTEGRATOR’S MANUAL Description String type Two byte cell ID in hexadecimal format 6.
PAGE 121
7. Data - HSCSD 7.1 AT+CHSC HSCSD Current Call Parameters Description Command Possible Responses Show current HSCSD call parameters AT+CHSC • • • • Test if command is supported AT+CHSC=? • +CME ERROR: • OK • ERROR +CHSC:,,, +CME ERROR: OK ERROR Returns information about the current HSCSD call parameters, i.e. the current number of receive and transmit timeslots, air interface user rate and channel coding. Description 0 No HSCSD call is active.
PAGE 122
GM28 INTEGRATOR’S MANUAL 7.2 AT+CHSD HSCSD Device Parameters Description Command Possible Responses Show HSCSD features supported by the ME/ TA AT+CHSD • +CHSD: ,, ,, • +CME ERROR: • OK • ERROR Test if command is supported AT+CHSD=? • +CME ERROR: • OK • ERROR Shows information about HSCSD features supported by the ME/TA.
PAGE 123
7. DATA - HSCSD 7.3 AT+CHSN HSCSD Non Transparent Call Configuration Description Command Possible Responses Set HSCSD configuration.
PAGE 124
GM28 INTEGRATOR’S MANUAL 7.
PAGE 125
7. DATA - HSCSD but before possible TE-TA rate (+ILRR) reporting and before the intermediate result code CONNECT is transmitted. The format of the intermediate result code is: +CHSR: ,,, For the value definitions, refer to “AT+CHSC HSCSD Current Call Parameters”, page 121. For instance, for a non-transparent HSCSD call, result code ‘CHSR: 2, 1, 4, 8’ means that the call has two timeslots downlink, one timeslot uplink, the air interface user rate is 28.
PAGE 126
GM28 INTEGRATOR’S MANUAL 126 LZT 123 7468 P1A
PAGE 127
8. Fax 8.1 AT*E2FAX Ericsson M2M Fax Comm. Baud Rate Modification Description Command Possible Responses Request change of fax comm. baud rate AT*E2FAX= • ERROR • OK Displays currently set rate AT*E2FAX? • *E2FAX: • ERROR Shows if the command is supported AT*E2FAX=? • *E2FAX: (list of supported s) • ERROR This command allows the modification of the factory default RS232 comm. setting between standard 9600 baud and 19200 baud.
PAGE 128
GM28 INTEGRATOR’S MANUAL AT*E2FAX? *E2FAX: 0 OK (Current default setting is 19200 baud) AT*E2FAX=0 OK (Sets default RS232 setting to 9600 baud) 8.2 Low Level Fax Commands The following table of low level fax commands are supported and used by the GM28 for fax operation.
PAGE 129
9. Identification 9.1 AT Attention Command Description Command Possible Responses Checks the communication between the MS and application AT • OK • +CME ERROR This command is used to determine the presence of an MS. If the MS supports AT commands, it returns an OK final result code. 9.
PAGE 130
GM28 INTEGRATOR’S MANUAL 9.4 AT* List all Supported AT Commands Description Command Possible Responses List all implemented AT commands AT* [ […]] / [ […]] Lists all the commands supported by the MS. 9.
PAGE 131
9. IDENTIFICATION 9.7 AT+CGMR Description String type Model name for the transceiver unit, for example, GM28 Read MS Revision Identification Description Command Possible Responses Request MS revision identification string AT+CGMR • • +CME ERROR: Show if the command is supported AT+CGMR=? • OK • ERROR This command causes the MS to return a string containing information about the software version. 9.
PAGE 132
GM28 INTEGRATOR’S MANUAL This command provides compatibility with Microsoft Windows 95. 9.10 AT+GCAP Description 0 Same information as +GMM command (model identification) 1 Same information as +GMR command (revision identification) 3 Modem model description 5 Active settings 7 Modem configuration profile (brief listing of the modem functionality: fax classes, Bluetooth, IrDA, modem type, etc.
PAGE 133
10. Interface 10.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 10.2 AT&C Circuit 109 (DCD) Control Description Command Possible Responses Set behavior of carrier detect AT&C[] OK ERROR Determines the behaviour of the carrier detect. 10.3 AT&D Description 0 DCD always on 1 DCD follows the connection.
PAGE 134
GM28 INTEGRATOR’S MANUAL 10.4 AT&S Circuit 107 (DSR) Response Description Command Possible Responses Set behaviour of data set ready AT&S[] • OK • ERROR Determines the behaviour of the data set ready signal. 10.5 AT+WS46 Description 0 DSR always on 1 DSR on in data mode. DSR off in command mode.
PAGE 135
10. INTERFACE 10.6 ATE Command Echo Description Command Possible Responses Request Command Echo ATE[] ATE=[] • OK • ERROR Show the current setting ATE? Show if the command is supported ATE=? E: (list of supported s) The setting of this parameter determines whether or not the DCE echoes characters received from the DTE during command state and online command state. 10.
PAGE 136
GM28 INTEGRATOR’S MANUAL List of result codes 10.
PAGE 137
10. INTERFACE Commands included on the same command line as the Z command will be ignored. 10.9 AT+CMUX Description 0 Select the user profile to restore Switch to 07.10 Multiplex Protocol Description Command Possible Responses Switch to 07.
PAGE 138
GM28 INTEGRATOR’S MANUAL Description 1 9600bits/s 2 19200bits/s 3 38400bits/s 4 57600bits/s 5 115200bits/s 6 230400bits/s 7 460800bits/s Description 31 Default maximum frame size Description 10 100ms default timer Description 3 Default maximum number of re-transmissions Description 30 300ms default timer Description 10 10s default timer Description 1..
PAGE 139
10. INTERFACE 10.10 AT+CRES Restore SMS Settings Description Command Possible Responses Restore settings AT+CRES[=] • +CMS ERROR: • OK • ERROR Get available profiles AT+CRES=? • +CRES: (list of supported s) • +CMS ERROR: • OK • ERROR Restores message service settings from non-volatile memory to active memory. A TA can contain several profiles of settings.
PAGE 140
GM28 INTEGRATOR’S MANUAL 10.12 AT+IFC Description 3 Space. Default value DTE-DCE Local Flow Control Description Command Possible Responses Defines DTE-DCE local flow control AT+IFC=[, []] • OK • ERROR Read the current setting AT+IFC? +IFC: , Show if the command is supported AT+IFC=? +IFC: (list of supported s,s) Defines the flow control between the modem and the computer when in on-line data mode.
PAGE 141
10. INTERFACE 10.13 AT+ILRR Cable Interface Local Rate Reporting Description Command Possible Responses Defines DTE-DCE character framing AT+ILRR= • OK • ERROR Read the current setting AT+ILRR? +ILRR: Show if the command is supported AT+ILRR=? +ILRR:(list of supported s) Specifies whether or not the extended-format “+ILRR:” information text is transmitted from the DCE to the DTE.
PAGE 142
GM28 INTEGRATOR’S MANUAL The specified rate takes effect following the issuance of any result code(s) associated with the current command line. Description Discrete integer value The value specified shall be the rate in bits per second at which the DTE-DCE interface should operate, e.g. “19200” or “115200”. The rates supported by a particular DCE are manufacturer specific. The following rates, are supported; 1200 2400 4800 9600 19200 38400 57600 115200 230400 460800 10.
PAGE 143
11. Network 11.1 AT*E2CD Ericsson M2M Cell Description Description Command Possible Responses Request network cell description AT*E2CD= • ERROR • OK Read the command AT*E2CD? • *E2CD: ,,, • ERROR Show if the command is supported AT*E2CD=? • *E2CD: (list of supported s) • ERROR Controls the presentation of an unsolicited result code E2CD: when =1, or when there is a change in one of the network cell parameters, E2CD: ,,.
PAGE 144
GM28 INTEGRATOR’S MANUAL Description 0-63 According to GSM 04.18 V8.6.0, the coding of the timing advance value is the binary representation of the timing advance in bit periods; 1 bit period = 48/13 ìs.
PAGE 145
11. NETWORK 11.
PAGE 146
GM28 INTEGRATOR’S MANUAL There are four presentation format modes (Display, Compact, Verbose, and Reduced Display) and two response types (one shot response or continuous unsolicited responses). The purpose of the presentation format mode Display is to display the data in a readable form, including headers and line breaks (). This format is, however, not well suited for machine decoding. The formats Verbose, Compact and Reduced Display do not have headers or line breaks.
PAGE 147
11.
PAGE 148
GM28 INTEGRATOR’S MANUAL Description 4 Enable compact network location information unsolicited result code.
PAGE 149
11. NETWORK Description Integer type Received Signal Strength level in dBm measured on idle mode Description Integer type Received Signal Strength level in dBm. The Rx Level is taken in the Downlink and statistically is applied to 100 TDMA frames of the TCH or during a SACCH multiframe Description Integer type Received Signal Strength level in dBm.
PAGE 150
GM28 INTEGRATOR’S MANUAL Description 4 1.9% < BER < 2.7% 5 3.8% < BER < 5.4% 6 7.6% < BER < 11.0% 7 BER > 15.0% Description Integer Path Loss criterion parameter for neighbour cells. The MS calculates this parameter, in idle mode, to decide if the cell is suitable to camp on. After the calculation the criterion is C1 > 0. See GSM 05.08 Description Integer Cell reselection parameter for neighbour cells.
PAGE 151
11. NETWORK 11.3 AT*E2SPN M2M Service Provider Indication Description Command Possible Responses Request service provider indication AT*E2SPN • *E2SPN: • +CME ERROR: Show if the command is supported AT*E2SPN=? • OK • ERROR Causes the MS to return the service provider name stored in the SIM card ( parameter). The text will consist of a maximum of 16 bytes containing the service provider name stored in the EFSPN file in the SIM card (see GSM 11.11).
PAGE 152
GM28 INTEGRATOR’S MANUAL 11.5 AT*ECSP Ericsson Customer Service Profile Description Command Possible Responses Read the customer service profile from the SIM AT*ECSP= • *ECSP: , • +CME ERROR: • OK • ERROR Test if the command is supported AT*ECSP=? • +CME ERROR: • OK • ERROR This command is used to read the customer service profile (CSP) from the SIM. CSP is a list on the SIM, which indicates the services that are user accessible.
PAGE 153
11. NETWORK 11.6 AT*EPNR Ericsson Read SIM Preferred Network Description Command Possible Responses Read entries in SIM preferred list AT*EPNR= [, [,,[...
PAGE 154
GM28 INTEGRATOR’S MANUAL 11.7 AT*EPNW Ericsson Write SIM Preferred Network Description Command Possible Responses Write/delete entries in SIM preferred list AT*EPNW=[] [,,] • +CME ERROR: • OK • ERROR Test if the command is supported and list the possible settings AT*EPNW=? • *EPNW: (list of supported s), (list of supported )s • +CME ERROR: • OK • ERROR This command is used to edit the SIM preferred list of networks (EFPLMNSEL).
PAGE 155
11. NETWORK EXAMPLES AT*E2SSN? 8944110063503224707 OK where the raw data contained in the ICCid field on the SIM is 984411003605234207F7. Test command: AT*E2SSN=? OK 11.
PAGE 156
GM28 INTEGRATOR’S MANUAL 11.10 AT+CIMI Subscriber Identification Description Command Possible Responses Read IMSI AT+CIMI • • • • Show if the command is supported AT+CIMI=? • OK • ERROR +CME ERROR OK ERROR Causes the TA to return , identifying the individual SIM attached to the ME. Description string without double quotes International Mobile Subscriber Identity 11.
PAGE 157
11.
PAGE 158
GM28 INTEGRATOR’S MANUAL Description 16 Data circuit sync 32 Data circuit async 64 Dedicated packet access 128 Voice L2 1..30 When “no reply” is enabled or queried, this gives the time in seconds to wait before the call is forwarded. Default value is 20 11.
PAGE 159
11. NETWORK Description 0 Asynchronous modem 4 Voice 5 Fax Description 0 3.1kHz 1 UDI 11.
PAGE 160
GM28 INTEGRATOR’S MANUAL Test command returns values supported by the TA as a compound value. Description 0 Disable 1 Enable Description 0 COLP not provisioned 1 COLP provisioned 2 unknown (e.g. no network, etc.
PAGE 161
11. NETWORK 11.
PAGE 162
GM28 INTEGRATOR’S MANUAL Description 0 Unknown 1 Available 2 Current 3 Forbidden 11.
PAGE 163
11. NETWORK 11.
PAGE 164
GM28 INTEGRATOR’S MANUAL Unsolicited Result Codes *ECPV - Ciphering Indicator SYNTAX - Unsolicited Result code Description Response When Set command informs the TE when a communication is unsecured due to the fact that the network is not enciphering the communication *ECPV: When AT*ECPI enables it, the *ECPV: is sent during a connection whenever the communication is not enciphered.
PAGE 165
11. NETWORK 11.
PAGE 166
GM28 INTEGRATOR’S MANUAL Description String Type Three digits in decimal format. The Mobile Country Code identifies the PLMN serving cell country according to ITU Description String Type Two digits in decimal format.
PAGE 167
12. Phonebook 12.1 AT*E2PBCS Ericsson M2M Phonebook Check Sum Description Command Possible Responses Request phone book checksum AT*E2PBCS • *E2PBCS: • +CME ERROR: Show if the command is supported AT*E2PBCS=? • OK • ERROR Command causes the ME to return the phone book checksum stored internally . Phone book checksum is recalculated whenever there is a change in the phone book.
PAGE 168
GM28 INTEGRATOR’S MANUAL 12.3 AT*ESCG Description 1-10 The group index within the hierarchical phone book Description 1 Contact 2 Phone number Description Integer The index of the contact/group/phone number to add. The parameter has the following meaning: if the item to add is a contact, the is the index of the contact in the contacts book.
PAGE 169
12. PHONEBOOK 12.
PAGE 170
GM28 INTEGRATOR’S MANUAL Description 1 Index number to the first credit card call access server 2 Index number to the second credit card call access server Description 0 Credit card calling disabled 1 Index number to the first credit card call access server 2 Index number to the second credit card call access server Description String Character string <0..9,+>, max.
PAGE 171
12. PHONEBOOK 12.5 AT*ESDG Ericsson Delete Group Description Command Possible Responses Deletes a group defined in the hierarchical phone book AT*ESDG= • +CME ERROR: • OK Show if the command is supported and list the possible AT*ESDG=? • *ESDG: list of s • OK This command deletes the group at position from the hierarchical phone book. 12.
PAGE 172
GM28 INTEGRATOR’S MANUAL 12.7 AT*ESGR Ericsson Group Read Description Command Possible Responses Lists the groups defined in the hierarchical phone book AT*ESGR • *ESGR: , [ , ..] • OK • ERROR Shows if the command is supported AT*ESGR=? OK This command lists the groups in the hierarchical phone book. 12.
PAGE 173
12. PHONEBOOK 12.
PAGE 174
GM28 INTEGRATOR’S MANUAL 12.10 AT+CPBF Phonebook Find Description Command Possible Responses Shows the current setting +CPBF= • +CPBF: ,,, [[...]+CBPF: ,,, ] • +CME ERROR: • OK • ERROR Show if the command is supported +CPBF=? • • • • +CPBF: , +CME ERROR: OK ERROR Returns phone book entries whose alphanumeric field starts with .
PAGE 175
12. PHONEBOOK Description string type Phone number of format Description 129 ISDN/telephony numbering plan, national/international unknown 145 ISDN/telephony numbering plan, international number 161 ISDN/telephony numbering plan, national number 128 - 255 Other values refer to GSM 04.08 section 10.5.4.7 Description string type Field of maximum length ; character set as specified by the select TE character set command, +CSCS.
PAGE 176
GM28 INTEGRATOR’S MANUAL 12.12 AT+CPBS Phone Storage Description Command Possible Responses Set phone book storage AT+CPBS= [,] • +CME ERROR • OK • ERROR Read the current setting AT+CPBS? • • • • Test if the command is supported AT+CPBS=? • +CPBS: (list of supported s) • +CME ERROR • OK • ERROR +CPBS: +CME ERROR OK ERROR Selects phone book memory storage , which is used by other phone book commands.
PAGE 177
12. PHONEBOOK 12.13 AT+CPBW Phonebook Write Description Command Possible Responses Request phone book write AT+CPBW=[] [, [, [,]]] • +CME ERROR • OK • ERROR Show if the command is supported AT+CPBW=? • +CPBW: (list of supported s), ,(list of supported s), • +CME ERROR • OK • ERROR Writes phone book entry in location number in the current phone book memory storage area, selected with AT+CPBS.
PAGE 178
GM28 INTEGRATOR’S MANUAL Description integer type Value indicating the maximum length of field 178 LZT 123 7468 P1A
PAGE 179
13. Short Message Services - Point to Point 13.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 13.2 AT+CGSMS Select Service for MO SMS Messages See 6.10, AT+CGSMS Select Service for MO SMS Messages 13.
PAGE 180
GM28 INTEGRATOR’S MANUAL Test command returns lists of memory storage supported by the TA. Description string type Memory from which messages are read and deleted (commands List Messages +CMGL, Read Message +CMGR and Delete Message +CMGD) “ME” ME message storage “SM” SIM message storage.
PAGE 181
13. SHORT MESSAGE SERVICES - POINT TO POINT 13.4 AT+CSCA Service Centre Address Common for both PDU and Text Modes Description Command Possible Responses Set service centre address AT+CSCA= [,] • OK • ERROR Show the current setting AT+CSCA? • +CSCA: , • OK • ERROR Show if the command is supported AT+CSCA=? • OK • ERROR Updates the SMSC address, through which mobile originated SMs are transmitted.
PAGE 182
GM28 INTEGRATOR’S MANUAL 13.5 AT+CMGF Message Format Common for both PDU and Text Modes Description Command Possible Responses Set message format AT+CMGF= • OK • ERROR Read the current setting AT+CMGF? • +CMGF: • OK • ERROR Show if the command is supported AT+CMGF=? • +CMGF: (list of supported s) • OK • ERROR This command tells the TA, which input and output format to use for messages.
PAGE 183
13. SHORT MESSAGE SERVICES - POINT TO POINT same as specified by the send message command, +CMGS. If writing fails, final result code +CMS ERROR: is returned. See “AT+CPMS Preferred Message Storage”, page 179.
PAGE 184
GM28 INTEGRATOR’S MANUAL Note! SMS-COMMANDs and SMS-STATUS-REPORTs cannot be stored in text mode. Description 2 Stored unsent message (only applicable to SMs) Description String type GSM 03.40 TP-Originating-Address Value in string format; BCD numbers (or GSM default alphabet characters) are converted to characters of the currently selected TE character (refer command +CSCS). Type of address given by Description String type GSM 03.
PAGE 185
13. SHORT MESSAGE SERVICES - POINT TO POINT 13.7 AT+CMGS Send Message PDU Mode Description Command Possible Responses Send message AT+CMGS= PDU is given • +CMGS: [,] • +CMS ERROR: • OK • ERROR Show if the command is supported AT+CMGS=? • OK • ERROR Sends a message from a TE to the network (SMS-SUBMIT). Message reference value is returned to the TE on successful message delivery.
PAGE 186
GM28 INTEGRATOR’S MANUAL Description ... GSM 03.40 RP-User-Data element of RP-ACK PDU; format is same as for in case of SMS, but without GSM 04.
PAGE 187
13. SHORT MESSAGE SERVICES - POINT TO POINT carriage returns can be used (previously mentioned four character sequence shall be sent to the TE after every carriage return entered by the user); if TE character set is “HEX”: the entered text should consist of two IRA character long hexadecimal numbers which ME/TA converts to 7-bit characters of GSM alphabet (e.g.
PAGE 188
GM28 INTEGRATOR’S MANUAL AT+CMGS=“+447747008670” > Test SMS +CMGS: 15 OK 13.8 AT+CMSS Send From Storage PDU mode Description Command Possible Responses Send from storage AT+CMSS= • • • • Show if the command is supported AT+CMSS=? • OK • ERROR +CMSS: +CMS ERROR: OK ERROR Sends message with location value from message storage to the network (SMS-SUBMIT or SMS-COMMAND). Reference value is returned to the TE on successful message delivery.
PAGE 189
13. SHORT MESSAGE SERVICES - POINT TO POINT supports, is returned. If sending fails in a network or an ME error, final result code +CMS ERROR: is returned. This command is abortable. Description Integer type Value in the range of location numbers supported by the associated memory Description String type GSM 03.
PAGE 190
GM28 INTEGRATOR’S MANUAL TE on successful message delivery. Optionally (when +CSMS value is 1 and network supports) is returned. Values can be used to identify message upon unsolicited delivery status report result code. If sending fails in a network or an ME error, final result code +CMS ERROR: is returned. This command is abortable. Description Integer type Value indicating in PDU mode (+CMGF=0), the length of the actual TP data unit in octets (i.e.
PAGE 191
13. SHORT MESSAGE SERVICES - POINT TO POINT 8-bit octets (refer to +CMGS). Message reference value is returned to the TE on successful message delivery. Optionally, when +CSMS value is 1 and there is network support, is returned. Values can be used to identify message upon unsolicited delivery status report result code. If sending fails in a network or an ME error, final result code +CMS ERROR: is returned. This command is abortable.
PAGE 192
GM28 INTEGRATOR’S MANUAL 13.
PAGE 193
13. SHORT MESSAGE SERVICES - POINT TO POINT Description 0 No SMS-DELIVER indications are routed to the TE. No class, Class 0, class 1 and class 3 use as preferred storage. Class 2 messages shall be stored in the SIM. If it this is not possible then the MS shall send an error message accordingly to GSM 03.
PAGE 194
GM28 INTEGRATOR’S MANUAL Text Mode Description Command Possible Responses Set new message indication to TE AT+CNMI=[ [,[,[, ]]]] • +CMS ERROR: • OK • ERROR Shows the current setting AT+CNMI? • +CNMI: ,,, • OK • ERROR Show if the command is supported AT+CNMI=? • +CNMI: (list of supported s), (list of supported s), (list of supported s), (list of supported s) • OK • ERROR Selects the procedure for the way in which new messages received f
PAGE 195
13. SHORT MESSAGE SERVICES - POINT TO POINT Description 0 Store message to “BM” (or some manufacturer specific memory).
PAGE 196
GM28 INTEGRATOR’S MANUAL 13.11 AT+CMGR Read Message PDU Mode Description Command Possible Responses Read message AT+CMGR= • +CMGR: ,[],] • +CMS ERROR: • OK • ERROR Show if the command is supported AT+CMGR=? • OK • ERROR Returns message with location value from preferred message storage to the TE. Status of the message and entire message data unit is returned.
PAGE 197
13.
PAGE 198
GM28 INTEGRATOR’S MANUAL Description String type GSM 03.40 TP-Originating-Address Value in string format; BCD numbers (or GSM default alphabet characters) are converted to characters of the currently selected TE character (refer command +CSCS). Type of address given by Description String type GSM 03.
PAGE 199
13. SHORT MESSAGE SERVICES - POINT TO POINT The entered text should be formatted as follows: if (set with +CSMP) indicates that GSM 03.38 default alphabet is used and indicates that GSM 03.40 TP-User-Data-Header-Indication is not set: if TE character set other than "HEX" (refer command Select TE Character Set +CSCS in TS 07.
PAGE 200
GM28 INTEGRATOR’S MANUAL Description Integer GSM 03.40 TP--command-type. Default value is 0 Description Integer GSM 03.41 CBM serial number Description String type All different possible combinations of CBM message identifiers (refer ) (default is empty string); e.g. “0,1,5-7” GSM 03.41 CBM message identifier in integer format Description Integer format GSM 03.41 CBM page parameter bits 4-7 in integer format Description Integer type GSM 03.
PAGE 201
13. SHORT MESSAGE SERVICES - POINT TO POINT Description 0 - 143 (TP-VP+1) x 5 minutes (i.e. 5 minute intervals up to 12 hous) 144 - 167 12 hours + ((TP_VP-143) x 30 minutes) 168 - 196 (TP-VP-166) x 1 day 197 - 255 (TP-VP-192) x 1 week Description Integer type GSM 03.40 TP-message-number 13.
PAGE 202
GM28 INTEGRATOR’S MANUAL Description String type Manufacturing specific. Should be left empty but not omitted Description Integer type Value indicating in PDU mode (+CMGF=0), the length of the actual TP data unit in octets (i.e. the RP layer SMSC address octets are not counted in the length) Description In the case of SMS: GSM 04.11 SC address followed by GSM 03.
PAGE 203
13.
PAGE 204
GM28 INTEGRATOR’S MANUAL Description Integer Indicates the status of messages in memory 0 Received unread message (new message) 1 Received read message 2 Stored unsent message (only applicable to SMs) 3 Stored sent message (only applicable to SMs) 4 All messages (only applicable to +CMGL command) Description String type GSM 03.
PAGE 205
13. SHORT MESSAGE SERVICES - POINT TO POINT Description String type GSM 03.40 TP-service-centre-time-stamp in time-string format (refer
) Description Integer type Value indicating in PDU mode (+CMGF=0), the length of the actual TP data unit in octets (i.e. the RP layer SMSC address octets are not counted in the length) The entered text should be formatted as follows: if (set with +CSMP) indicates that GSM 03.
PAGE 206
GM28 INTEGRATOR’S MANUAL
Description String GSM 03.40 TP-Discharge-Time in string format "yy/MM/ dd,hh:mm:ss+-zz where characters indicate year, month, day, hour,minutes, seconds and time zone Description Integer GSM 03.40 TP-Status Description Integer GSM 03.40 TP-Command-Type (default 0) Description Integer GSM 03.
PAGE 207
13. SHORT MESSAGE SERVICES - POINT TO POINT 13.13 AT+CMGD Delete Message Common for both PDU and Text modes Description Command Possible Responses Delete message AT+CMGD= • +CMS ERROR: • OK • ERROR Show if the command is supported AT+CMGD=? • OK • ERROR Deletes message from preferred message storage location . If deleting fails, final result code +CMS ERROR: is returned. Test command shows the valid memory locations.
PAGE 208
GM28 INTEGRATOR’S MANUAL 13.
PAGE 209
13. SHORT MESSAGE SERVICES - POINT TO POINT 13.16 AT+CSCS Select Character Set Description Command Possible Responses Set command informs TA which character set is used by the TE AT+CSCS= • OK • ERROR Show the current setting AT+CSCS? • +CSCS: • OK • ERROR Show list of supported character sets AT+CSCS=? • +CSCS: (list of supported s) • OK • ERROR This command informs the TA which character set is used by the TE.
PAGE 210
GM28 INTEGRATOR’S MANUAL 13.17 AT+CSMS Select Message Service Common for both PDU and Text Modes Description Command Possible Responses Select message service AT+CSMS= • +CSMS: ,, • +CMS ERROR: • OK • ERROR Show supported message types along with the current service setting AT+CSMS? • +CSMS: ,,, • OK • ERROR Show list of supported services AT+CSMS=? • +CSMS: (list of supported s) • OK • ERROR Selects messaging service .
PAGE 211
13. SHORT MESSAGE SERVICES - POINT TO POINT Description 0...127 GSM 04.11 Annex E-2 values 128...255 GSM 03.40 subclause 9.2.3.22 values 300 ME failure 302 Operation not allowed 304 Invalid PDU mode parameter 310 SIM not inserted 311 SIM PIN required 312 PH-SIM PIN required 313 SIM failure 314 SIM busy 315 SIM wrong 316 SIM PUK required 317 SIM PIN2 required 318 SIM PUK2 required 500 Unknown error ...511 Other values in range 256...511 are reserved 512...
PAGE 212
GM28 INTEGRATOR’S MANUAL 212 LZT 123 7468 P1A
PAGE 213
14. Short Message Services - Cell Broadcast 14.1 AT+CNMI New Message Indications to TE See 13.10, AT+CNMI New Message Indications to TE 14.
PAGE 214
GM28 INTEGRATOR’S MANUAL 214 LZT 123 7468 P1A
PAGE 215
15. SIM Application Toolkit 15.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 15.
PAGE 216
GM28 INTEGRATOR’S MANUAL 15.3 AT*E2STKD M2M STK Display Text Description Command Possible responses Answer to the reception of DISPLAY TEXT AT*E2STKD= • +CME ERROR • OK • ERROR Test if the command is supported AT*E2STKD=? • *E2STKD: (list of supported ) • +CME ERROR • OK • ERROR The ME passes the parameters within DISPLAY TEXT command to the external application by means of the unsolicited result code *E2STKD.
PAGE 217
15. SIM APPLICATION TOOLKIT Values follow GSM 11.14 standard. Description 0 Display normal priority text 1 Display high priority text Description 0 Clear message after a dalay 1 Wait for user to clear message Description 0 Text is coded in unpacked format, using the SMS default 7bit coded alphabet, as defined in GSM 03.38 with bit 8 set to 0.
PAGE 218
GM28 INTEGRATOR’S MANUAL Answer command allows the external application to send the appropriate answer, after receiving the unsolicited result code, and before the timeout expires. If Answer command is sent once the timeout expires, an ERROR response is generated. If parameter is not 0, a failure has occurred and no more parameters are sent. If the extra parameters are sent, the ME indicates ERROR. Test command returns the list of supported values, and the maximum value of .
PAGE 219
15. SIM APPLICATION TOOLKIT Values follow GSM 11.14 standard. 15.5 AT*E2STKI Description 0 Text is coded in unpacked format, using the SMS default 7-bit coded alphabet, as defined in GSM 03.38 with bit 8 set to 0. It corresponds to data coding scheme of 8 bit 1 Text is coded in packed format, using the SMS default 7-bit coded alphabet, packed in 8-bit octets, as defined in GSM 03.38.
PAGE 220
GM28 INTEGRATOR’S MANUAL Test command returns the list of suported values, and . Values follow GSM 11.14 standard. Note! Description 0 OK. Performed as required: the text was displayed. It corresponds to ‘00’ command performed succesfully, described in the GSM standard 1 Failed. User terminated session: the text was displayed as requested and the user wants to end the proactive session.
PAGE 221
15. SIM APPLICATION TOOLKIT Values follow GSM 11.14 standard.
PAGE 222
GM28 INTEGRATOR’S MANUAL 15.6 AT*E2STKL M2M STK Select Item Description Command Possible responses Answer to the reception of SELECT ITEM AT*E2STKL=, [] • +CME ERROR • OK • ERROR Test if the command is supported AT*E2STKL=? • *E2STKL: (list of supported ), (list of supported ) • +CME ERROR • OK • ERROR The ME passes the parameters within SELECT ITEM command to the external application by means of the unsolicited result code *E2STKL.
PAGE 223
15. SIM APPLICATION TOOLKIT Unsolicited Result Codes: E2STKL: ,,, [,]E2STKL: ,, ,[…]E2STKL: , ,,] Values follow GSM 11.14 standard. Description 0 Text is coded in unpacked format, using the SMS default 7-bit coded alphabet, as defined in GSM 03.38 with bit 8 set to 0.
PAGE 224
GM28 INTEGRATOR’S MANUAL 15.
PAGE 225
15. SIM APPLICATION TOOLKIT Description 0 Remove the current menu 1 New menu to be displayed Unsolicited Result Codes: *E2STKM: ,,, E2STKM: ,, ,[[…]E2STKM: , ,,] Values follow GSM 11.14 standard. Description 0 Text is coded in unpacked format, using the SMS default 7bit coded alphabet, as defined in GSM 03.38 with bit 8 set to 0.
PAGE 226
GM28 INTEGRATOR’S MANUAL The parameters have no default values. 15.8 AT*E2STKN M2M STK Envelope (Menu Selection) Description Command Possible responses Do the menu selection AT*E2STKN= • +CME ERROR • OK • ERROR Test if the command is supported AT*E2STKN=? • *E2STKN: (list of supported ) • +CME ERROR • OK • ERROR The application informs the ME about the selected menu item by means of the AT*E2SKTN command. The ME answers with OK, or ERROR.
PAGE 227
15. SIM APPLICATION TOOLKIT Values follow GSM 11.14 standard. Description 0 OK. Performed as required. It corresponds to ‘00’ command performed succesfully, described in the GSM standard 1 Failed. User terminated session. It corresponds to ‘10’ Proactive session terminated by the user, described in the GSM standard 2 Failed. User requests backwards move. It corresponds to ‘11’ backward move in the proactive SIM session requested by the user 3 Failed. No response from user.
PAGE 228
GM28 INTEGRATOR’S MANUAL Description Integer type (0-240) Value indicating the maximum length of field Description String type Field of string type between “”. Coding is according to EFAND as defined in GSM 11.11 The maximum length is fixed 15.
PAGE 229
15. SIM APPLICATION TOOLKIT 15.11 *E2STKP STK Send SS Unsolicited Result Code: *E2STKP: , , , , , The ME passes the parameters within SEND SS command to the external application, by means of the unsolicited result code *E2STKP. This informs the external application that the ME has sent an SS string to the network, and provides the current status after this operation.
PAGE 230
GM28 INTEGRATOR’S MANUAL 15.12 *E2STKU STK Send USSD Unsolicited Result Code: *E2STKU: , , Description: The ME shall passes the parameter within SEND USSD command to the external application, by means of the unsolicited result code *E2STKU. This informs the external application that the ME is sending a USSD string to the network. Description 0 Text is coded in unpacked format, using the SMS default 7bit coded alphabet, as defined in GSM 03.
PAGE 231
15. SIM APPLICATION TOOLKIT 15.13 *E2STKR STK Refresh Unsolicited Result Code: *E2STKR: The ME informs the external application about the coming REFRESH command, by means of the unsolicited result code *E2STKR (eg Reset is coming).
PAGE 232
GM28 INTEGRATOR’S MANUAL Description 2 Set Up Call command timeout is set to the value of 3 Display Text command timeout is set to the value of 4 Get Input command timeout is set to the value of 5 Select Item command timeout is set to the value of Description Integer type (0-99) Specifies the value in seconds to be set in the timeout associated with the command specified in 0 All the commands timeouts are set to its default value (
PAGE 233
16. Supplementary Services 16.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 16.
PAGE 234
GM28 INTEGRATOR’S MANUAL 16.
PAGE 235
16. SUPPLEMENTARY SERVICES 16.4 AT+CAOC Advice of Charge Description Command Possible Responses Execute command AT+CAOC[=] • [+CAOC: ] +CME ERROR: • OK • ERROR Read command, shows the current mode AT+CAOC? • +CAOC: • OK • ERROR Test command, shows if the command is supported AT+CAOC=? • [+CAOC: (list of supported s] • OK • ERROR Use of Advice of Charge supplementary service command enables the subscriber to get information about the cost of calls.
PAGE 236
GM28 INTEGRATOR’S MANUAL 16.
PAGE 237
16. SUPPLEMENTARY SERVICES 16.
PAGE 238
GM28 INTEGRATOR’S MANUAL 16.
PAGE 239
16. SUPPLEMENTARY SERVICES 16.8 AT*ELIN Ericsson Line Set Description Command Possible Responses Set the current line to AT*ELIN= • • • • *ELIN: +CME ERROR: OK ERROR Read the current line AT*ELIN? • • • • *ELIN: +CME ERROR: OK ERROR Test if the command is supported AT*ELIN=? • *ELIN: list of supported s +CME ERROR: • OK • ERROR This command requests the ME to set the current line to .
PAGE 240
GM28 INTEGRATOR’S MANUAL Refer to GSM 02.30 for Public MMI services and codes. 16.10 AT*E2SSI Description String Type String in double quotes, containing a Public MMI command to modify, activate, interrogate or deactivate a Supplementary Service.
PAGE 241
16.
PAGE 242
GM28 INTEGRATOR’S MANUAL Description 81 MULTI_PARTY 112 ALL_CHARGING_SS 113 ADVICE_OF_CHARGE_INFORMATION 114 ADVICE_OF_CHARGE_CHARGING 144 ALL_BARRING_SERVICES 145 BARRING_OF_OUTGOING_CALLS 146 BARRING_OF_ALL_OUTGOING_CALLS 147 BARRING_OF_ALL_OUTGOING_INTERNATIONAL_CALLS 148 BARRING_OF_ALL_OG_INTERNATIONAL_NON_HPLMN_ DIRECTED_CALLS 153 BARRING_OF_INCOMING_CALLS 154 BARRING_OF_ALL_INCOMING_CALLS 155 BARRING_OF_ALL_IC_CALLS_WHEN_OUTSIDE_HPLMN Description
PAGE 243
16.
PAGE 244
GM28 INTEGRATOR’S MANUAL Description 4 SS_STATUS_PROVISIONED 7 SS_STATUS_PRA Description String Phone number string in double quotes Description 0-65532 Integer value for time Description 0 PERMANENT 1 TEMPORARY_DEFAULT_RESTRICTED 2 TEMPORARY_DEFAULT_ALLOWED Description 1 OVERRIDE_CATEGORY 2 CLI_RESTRICTION_OPTION 5 RESTRICTION_PER_CALL 244 LZT 123 7468 P1A
PAGE 245
16. SUPPLEMENTARY SERVICES 16.11 AT+CCFC Call Forwarding number and Conditions Description Command Possible Responses Request Calling forwarding number and conditions AT+CCFC= ,[,[,[, [,]]]] • +CME ERROR • when =2 and command successful: +CCFC: ,[,, [,]][ +CCFC: ,[,, [, ]][...
PAGE 246
GM28 INTEGRATOR’S MANUAL Description integer format Type of address octet 129 ISDN/telephony numbering plan, national/international unknown. Default value if ‘+’ is not in 145 ISDN/telephony numbering plan, international number. Default value if ‘+’ is in 161 ISDN/telephony numbering plan, national number 128 - 255 Other values Description integer format Type of subaddress octet 128 NSAP (X.213/ISO 8348 AD2), even number of address signals 136 NSAP (X.
PAGE 247
16. SUPPLEMENTARY SERVICES 16.
PAGE 248
GM28 INTEGRATOR’S MANUAL Description integer Sum of integers each representing a class of information.
PAGE 249
16. SUPPLEMENTARY SERVICES 16.
PAGE 250
GM28 INTEGRATOR’S MANUAL Description 2 Places all active calls (if any exist) on hold and accepts the other (held or waiting) call 2X Places all active calls on hold, except call X with which communication is supported 3 Adds a held call to the conversation 4 Connects the two calls and disconnects the subscriber from both calls (explicit call transfer) “X” is the numbering (starting with 1) of the call given by the sequence of setting up or receiving the calls (active, held or waiting) as see
PAGE 251
16. SUPPLEMENTARY SERVICES Description 0 CLIP not provisioned 1 CLIP provisioned 2 Unknown (e.g. no network) Unsolicited Result codes: +CLIP: , ,,, Defined values: 16.15 AT+CLIR Description String Type phone number of format specified by type of address octet in integer format (refer to GSM 04.08, subclause 10.5.4.
PAGE 252
GM28 INTEGRATOR’S MANUAL revoke this adjustment. If this command is used by a subscriber without provision of CLIR in permanent mode the network will act according GSM 02.81. The setting shall be per logical channel. When the MS is turned off and then turned on again the parameter setting shall turn back to default, i.e. the presentation of CLI shall be used according to the subscription of the CLIR service, is 0.
PAGE 253
16. SUPPLEMENTARY SERVICES 16.
PAGE 254
GM28 INTEGRATOR’S MANUAL Description 0 Disable the +CSSU result code presentation status in the TA 1 Enable the +CSSU result code presentation status in the TA Description 0 Unconditional call forwarding is active 1 Some of the conditional call forwarding are active 2 Call has been forwarded 3 Call is waiting 4 This is a CUG call (also present) 5 Outgoing calls are barred 6 Incoming calls are barred 7 CLIR suppression rejected Description 0…9 CUG index
PAGE 255
16. SUPPLEMENTARY SERVICES 16.
PAGE 256
GM28 INTEGRATOR’S MANUAL The different alternatives are shown below. Network Mobile Equipment External application 1 Signal Sends unsolicited result code +CUSD Result code presentation enabled, presented 2 Signal asking for reply Sends unsolicited result code +CUSD Result code presentation enabled, presented 3 Answer AT+CUSD 3b Sends AT+CUSD Description 0 Disable result code presentation in the TA 1 Enable result code presentation in the TA 2 Terminate (abort) USSD dialogue.
PAGE 257
16.
PAGE 258
GM28 INTEGRATOR’S MANUAL 258 LZT 123 7468 P1A
PAGE 259
17. Alphabetical Listing of AT Commands AT Command Description Page No.
PAGE 260
GM28 INTEGRATOR’S MANUAL AT Command Description Page No.
PAGE 261
17. ALPHABETICAL LISTING OF AT COMMANDS AT Command Description Page No.
PAGE 262
GM28 INTEGRATOR’S MANUAL AT Command Description Page No. AT+CMGC Send Command 189 AT+CMGD Delete Message 207 AT+CMGF Message Format 182 AT+CMGL List Message 201 AT+CMGR Read Message 196 AT+CMGS Send Message 185 AT+CMGW Write Message to Memory 182 AT+CMOD Call Mode AT+CMSS Send From Storage 188 AT+CMUX Switch to 07.
PAGE 263
17. ALPHABETICAL LISTING OF AT COMMANDS AT Command Description Page No.
PAGE 264
GM28 INTEGRATOR’S MANUAL AT Command Description Page No. ATT Select Tone Dialling ATV DCE Response Format ATX Call Progress Monitoring Control ATZ Reset to Default Configuration Unsolicited Result Code Description *E2STKE STK Send Short Message 228 *E2STKP STK Send SS 229 *E2STKR STK Refresh 231 *E2STKU STK Send USSD 230 62 135 63 136 Page No.