CDX-M620/M670 SERVICE MANUAL US Model CDX-M620/M670 Ver 1.0 2001. 03 AEP Model UK Model E Model CDX-M670 • The tuner and CD sections have no adjustments. SPECIFICATIONS AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.
CDX-M620/M670 Inputs Tone controls Loudness Power requirements Dimensions Mounting dimensions Mass Supplied accessories Telephone ATT control lead Illumination control lead BUS control input connector BUS audio input connector Antenna input connector (US model) Aerial input connector (AEP, UK, E model) AUX IN connector (US model) Bass ±8 dB at 100 Hz Treble ±8 dB at 10 Hz +8 dB at 100 Hz +2 dB at 10 Hz 12 V DC car battery (negative earth) Approx. 178 × 50 × 182 mm (w/h/d) Approx.
CDX-M620/M670 NOTE FOR THE OPENING OF THE FRONT PANEL In this set, the front panel is lowered to below the bottom face when it is opened. When servicing the set, place it on a stand having a height of about 2 cm. TABLE OF CONTENTS 1. GENERAL ........................................................................... 4 2. DISASSEMBLY 2-1. Front Panel Assy (Normal) ............................................... 16 2-2. Front Panel Assy (Inoperative) ......................................... 16 2-3.
CDX-M620/M670 SECTION 1 GENERAL US MODEL AEP, UK, E MODEL 4 This section is extracted from instruction manual.
CDX-M620/M670 US, AEP, UK, E MODEL 5
CDX-M620/M670 US MODEL 6
CDX-M620/M670 AEP, UK, E MODEL 7
CDX-M620/M670 8
CDX-M620/M670 9
CDX-M620/M670 US, AEP, UK, E MODEL 10
CDX-M620/M670 11
CDX-M620/M670 US MODEL Connection 12
CDX-M620/M670 13
CDX-M620/M670 AEP, UK, E MODEL Connection 14
CDX-M620/M670 15 15
CDX-M620/M670 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. Front Panel Assy (Normal) 2-2.
CDX-M620/M670 2-4. SUB PANEL (CD) SUB ASSY 1 CN603 4 claw 3 PTT 2.6x6 5 claw 2 PTT 2.6 x6 6 sub panel (CD) sub assy 2-5. MOTOR BLOCK ASSY, CAM (R) ASSY Note : Install the motor block assy and cam (R) assy in this roder. For phase alignment between cams (L) and (R), see page 22 and 24. 1 PTT 2.6x6 4 PTT 2.6x6 5 motor block assy Note: Install the cam (R) assy with the cam fully rotated in the direction of the arrow A.
CDX-M620/M670 2-6. MAIN BOARD 5 MAIN board 4 PTT 2.6x6 ground point 3 PTT 2.6x6 ground point 2 PTT 2.6x6 1 PTT 2.6x6 2-7. HEAT SINK 5 heat sink 4 PTT 2.6x6 3 PTT 2.6x10 2 PTT 2.6x6 1 PTT 2.
CDX-M620/M670 2-8. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the lead wires. 4 chassis (T) sub assy black red white 2-9.
CDX-M620/M670 2-10. SERVO BOARD 7 special screws 6 special screws 2 CN2 3 Removal the solders. 1 CN3 4 P 2x3 8 SERVO board 5 loading motor assy 2-11. SHAFT ROLLER ASSY 3 retaing ring (RA) 4 shaft retainer (roller) shaft retainer (roller) washer arm arm washer shaft retainer (roller) retaing ring (RA) Fig.
CDX-M620/M670 2-12. FLOATING BLOCK ASSY 6 floating block assy 7 compression spring (FL) 1 tension spring (KF1) 8 compression spring (FL) 4 Fit lever (D) in the direction of the arrow. 5 Turn loading ring in the direction of the arrow. 2 damper (T) 3 damper (T) 2-13.
CDX-M620/M670 SECTION 3 PHASE ALIGNMENT 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 3 arm (A-L) assy 4 stop ring 1.5, type-E 2 stop ring 1.5, type-E 1 arm (B-L) assy bracket (L) assy 3-2. CAM (L) 1 Move the arm (B-L) assy in the direction of the arrow A and the arm (A-L) assy in the direction of the arrow B fully (full open state). 2 Align the hole (large) on the cam (L) with part C and install the cam. 4 Turn the cam (L) clockwise and counterclockwise to verify that both the arms are operated. 3 stop ring 1.
CDX-M620/M670 3-3. MOTOR BLOCK 1 Turn the cam (L) and position the cam so that part A does not touch the SWITCH board SW900. 3 PTT 2.6x6 4 PTT 2.6x6 2 motor block SWITCH board 5 PTT 2.6x6 SW1001 SW1002 cam (L) A 3-4. ALIGNMENT BETWEEN ARM (A-L) ASSY AND ARM (B-L) ASSY 1 Input 9V DC to the motor terminal until the cam (L) stops rotating. Take care to avoid overload of the motor. 2 Verify that the arm (A-L) assy and arm (B-L) assy are positioned as shown below (full open).
CDX-M620/M670 3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 3 arm (A-R) assy 4 stop ring 1.5, type-E 2 stop ring 1.5, type-E 1 arm (B-R) assy bracket (R) assy 3-6. CAM (R) 1 Move the arm (B-R) assy in the direction of the arrow A and the arm (A-R) assy in the direction of the arrow B fully (full open state). 2 Align the hole (large) on the cam (R) with part C and install the cam. 4 Turn the cam (R) clockwise and counterclockwise to verify that both the arms are operated. 3 stop ring 1.
CDX-M620/M670 SECTION 4 DIAGRAMS 4-1. IC PIN DESCRIPTIONS • IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name I/O Pin Description 1 DVDD — Digital power supply pin 2 3 DVSS SOUT — O Digital ground Servo brock serial data output (Not used.) 4 5 SOCK XOLT O O Servo brock serial data read clock output (Not used.) Servo brock serial data latch output (Not used.) 6 7 SQSO SQCK O I Sub Q 80 bit, PCM peak and level data output.
CDX-M620/M670 Pin No. 52 Pin Name TE I/O I Tracking error signal input 53 54 CE RFDC I I Center servo analog input RF signal input 55 56 ADIO AVSSO O — Test pin (Not used.) Analog ground 57 58 IGEN AVDDO I — Constant current input from OP amplifier. Analog ground 59 60 ASYO ASYI O I EFM full-swing output (“L”: VSS, “H”: VDD) Asymmetry comparate voltage input 61 62 RFAC AVSS3 I — EFM signal input Analog ground 63 64 CLTV FILO I O VCO control voltage input from master.
CDX-M620/M670 • IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name I/O 1 ITRPT — Not used in this set. Pin Description 2, 3 4, 5 — NCO — — Not used in this set. Not used in this set. 6 7 OPEN CLOSE I O Front panel open detection input Front panel close control output 8 9 LINKOFF NCO I — Bus interface link input Not used in this set. 10 11 D SW SSTP I I 12, 13 14, 15 NCO — — — Not used in this set. Not used in this set.
CDX-M620/M670 Pin No. 57 Pin Name SENS I/O I SENS signal input 58 59 — — — — Not used in this set. Not used in this set. 60 61 BU.
CDX-M620/M670 • IC501 MB90574BPMT-G-321-BND (SYSTEM CONTROL) (MAIN BOARD) (US MODEL) • IC501 MB90574BPMT-G-322-BND (SYSTEM CONTROL) (MAIN BOARD) (AEP, UK, E MODEL) Pin No. Pin Name I/O Pin Description 1–3 (NCO) O Not used. (Open) 4 5 SP LATCH ATT O O Spectrum analyzer data latch signal System mute signal 6 7 SYS RST (NCO) O O System reset signal Not used. (Open) 8 9 VCC (NCO) — O Power supply pin (+5 V) Not used.
CDX-M620/M670 Pin No. 57 Pin Name DDC ON I/O O Pin Description DC/DC converter power control signal 58 59 CD EJECT OK CD OPEN REQ O I CD eject control signal Front panel open request signal 60 61 (NCO) OPEN KEY O I Not used. (Open) OPEN key detection signal 62 63 NOSE SW VSS I — Nose SW detection signal Ground 64 65 DETACH SW PWM I I Detach SW detection signal Oscillation frequency count input 66 – 68 69 (NCO) FLASH W O I Not used.
CDX-M620/M670 Pin No. 112 Pin Name 4V SEL I/O I Pin Description 4V select control signal 113 114 (NCO) TUN ON O O Not used. (Open) Tuner power control signal 115 116 LED SW1 LED SW2 O O Illumination select control signal 1 Illumination select control signal 2 117 118 (NCO) (NCO) O O Not used. (Open) Not used. (Open) 119 120 VSS (NCO) — O Ground Not used.
CDX-M620/M670 • IC702 HD643255A36F (SUB SYSTEM CONTROL) (MAIN BOARD) Pin No. Pin Name I/O 1 SA CLK O Not used. (Open) Pin Description 2 3 PG4 VSS O — Not used. (Open) Ground 4 5 NC VCC — — Not used. (Open) Power supply pin (+ 5V) 6–9 10 PC0 – PC3 VSS O — Not used. (Open) Ground 11 – 14 15 – 18 PC4 – PC7 PB0 – PB3 O O Not used. (Open) Not used. (Open) 19 20 – 23 VSS PB4 – PB7 — O Ground Not used. (Open) 24 – 27 28 PA0 – PA3 VSS O — Not used.
CDX-M620/M670 Pin No. 83 Pin Name STBY I/O I Hardware standby signal Pin Description 84 85 VCC XTAL — — Power supply pin (+5 V) Crystal oscillator (18.432 MHz) 86 87 EXTAL VSS — — Crystal oscillator (18.432 MHz) Ground 88 89 PF7 VCC O — Not used. (Open) Power supply pin (+5 V) 90 – 96 97 PF6 – PF0 UNI SO O O Not used. (Open) SONY BUS serial data output 98 99, 100 UNI SI VSS I — SONY BUS serial data input Ground 101 102 UNI CKI P53 I O SONY BUS serial clock input Not used.
CDX-M620/M670 4-3. BLOCK DIAGRAM — CD SECTION — 4 RF AMP, LD APC, ERROR AMP IC1 OPTICAL PICK-UP KSS-720A CDL ATT DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR IC501 CD SYSTEM CONTROL IC5 5 C B C 7 B 6 RF EQ RFO 16 61 RFAC EFM DEM D/A I/F LOUT1 D/A LOUT2 CONV.
CDX-M620/M670 4-4.
CDX-M620/M670 4-5.
CDX-M620/M670 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) • Waveforms — Servo Board — • Waveforms — Main Board — (MODE: CD PLAY) (MODE: FM) 1 1 for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance.
CDX-M620/M670 4-6.
CDX-M620/M670 • Semiconductor Location (Page 43) 39 39 Ref. No.
CDX-M620/M670 • Refer to page 37 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 54 for IC Block Diagrams. IC B/D (Page 41) (Page 46) Note: • Voltage is dc with respect to ground under no-signal conditions.
CDX-M620/M670 • Refer to page 37 for Waveforms. 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 54 for IC Block Diagrams. (Page 40) IC B/D (Page 40) Note: • Voltage is dc with respect to ground under no-signal conditions.
CDX-M620/M670 4-9. PRINTED WIRING BOARDS — MAIN SECTION — • Semiconductor Location Ref. No. Location Ref. No.
CDX-M620/M670 (Page 39) (Page 48) • Semiconductor Location Ref. No. D101 D102 D105 D106 D301 D305 Location E-3 F-3 D-1 E-2 B-7 B-8 Ref. No. D306 D307 D308 D401 D405 D501 Location B-8 B-8 B-8 B-3 C-5 B-2 Ref. No. D502 D504 D508 D510 D603 D607 Location H-4 I-4 H-4 G-4 G-5 G-4 Ref. No. D608 D610 D611 D651 D652 D801 Location G-7 B-2 B-2 I-3 J-4 J-12 Ref. No. D802 D803 D805 D806 Location J-10 J-5 J-10 J-11 IC309 A-7 Ref. No. IC601 IC701 Location G-5 I-12 Q103 Q106 Q113 E-2 F-2 E-1 43 Ref. No.
CDX-M620/M670 • Refer to page 37 for Waveforms. 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 54 for IC Block Diagrams. (Page 45) IC B/D (Page 46) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 54 for IC Block Diagrams. IC B/D (Page 44) IC B/D IC B/D (Page 46) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 • Refer to page 37 for Waveforms. 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 54 for IC Block Diagrams. (Page 45) (Page 44) IC B/D (Page 40) (Page 47) IC B/D Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 • Refer to page 37 for Waveforms. 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 54 for IC Block Diagrams. (Page 51) (Page 46) (Page 49) IC B/D Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 4-14. PRINTED WIRING BOARD — SUB (CD) SECTION — (Page 43) • Semiconductor Location Ref. No.
CDX-M620/M670 4-15. SCHEMATIC DIAGRAM — SUB (CD) SECTION — • Refer to page 55 for IC Block Diagram. (Page 47) IC B/D Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 4-16. PRINTED WIRING BOARD — KEY SECTION — • Semiconductor Location (Page 52) ( Ref. No. (D7) (D8) Location A-8 A-9 (IC1) B-7 LED1 LED2 LED3 LED4 B-4 B-10 B-2 B-3 Ref. No. LED5 LED6 LED7 LED8 LED9 LED10 LED11 LED12 LED13 Location B-2 B-3 C-1 C-3 C-13 C-2 A-3 A-2 C-13 Ref. No.
CDX-M620/M670 4-17. SCHEMATIC DIAGRAM — KEY SECTION — (Page 53) (Page 47) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 4-18. PRINTED WIRING BOARD — DISPLAY SECTION — (Page 50) • Semiconductor Location Ref. No. (D61) (D62) (D63) (D64) (D65) (D66) (D67) (D68) (D70) ( Location A-11 A-2 A-2 A-3 A-3 A-3 B-10 A-12 A-13 Ref. No. (IC60) (IC61) (IC62) Location B-9 B-11 A-13 LED60 LED62 LED63 LED64 LED65 A-1 A-2 A-12 B-2 B-12 Ref. No.
CDX-M620/M670 4-19. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 55 for IC Block Diagrams. (Page 51) IC B/D Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
CDX-M620/M670 • IC BLOCK DIAGRAMS IC1 CXA2596M IC7 LA6576L-TE-L IC306 TC7660SE0A713 APC PD AMP + – 1 VCC VEE 1 REV 2 CH2-CH4 OUTPUT ON/OFF MUTE2 35 MUTE2 VCC2 3 CH1 OUTPUT ON/OFF MUTE1 34 MUTE1 23 LC/PD 2 VREF 1.25V + – + – APC LD AMP VL0+ 21 HOLD SW + – VO4+ 7 VO3+ 8 VIN1/VREF SW VO3– 18 RFTC VC 14 13 12 11 10 9 VERF. +2.5V VCC REFERENCE VOLTAGE 26 REG-IN VO2– 11 – + +2.
CDX-M620/M670 ACINRL ACINRF ACINRR OUTLF OUTLR OUTRF OUTRR OUTSWL OUTSWR OUTSSL OUTSSR IC305 TDA7406TR 33 32 31 30 29 28 27 26 25 24 23 MIXER MONO- MONOFADER FADER ACINLF 34 SWINR 35 SWINL 36 ACIN ACOUTR 37 ACOUTL 38 MAIN MONO- MONOFADER FADER MONO- MONOFADER FADER FRONT OUTPUT SELECTOR SUBWOOFER +PHASE CONTROL REAR SW SECOND CREF 39 22 VDD IIC-BUS LP VOICE BANDPASS HP 21 SCL 20 SDA BASS SUPPLY TREBLE DIGITAL CONTROL HIGH-CUT VOLUME SOFTMUTE COMPANDER 19 GND 18 EXT-ATT
CDX-M620/M670 SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ...
CDX-M620/M670 5-2. CAM SECTION 59 58 55 57 #5 56 #2 #2 61 60 M601 #4 #2 #5 #2 58 64 #2 #2 54 65 63 #5 62 53 #12 51 #5 #5 #5 52 Ref. No. Part No. Description 51 52 53 54 55 3-230-495-01 X-3380-549-1 X-3380-544-1 X-3380-548-1 X-3380-546-1 CAM (L) ARM (B-R) ASSY BRACKET (L) ASSY ARM (B-L) ASSY ARM (A-L) ASSY 56 57 58 59 3-376-464-11 3-045-714-01 3-342-940-01 3-045-713-01 SCREW (+PTT 2.6X6), GROUND POINT GEAR (B) WASHER (M) GEAR (A) Remark 66 Ref. No. Part No.
CDX-M620/M670 5-3. MAIN BOARD SECTION 113 #2 #2 #2 #3 108 114 112 107 #2 109 #2 #2 110 115 #2 #2 111 #2 104 TUX201 106 105 107 106 F901 104 103 103 102 101 Ref. No. Part No.
CDX-M620/M670 5-4. FRONT PANEL (KEY) ASSY SECTION front panel (DSPL) assy 171 #6 172 173 174 170 169 178 175 not supplied (KEY board) #6 168 166 LCD1 176 164 177 165 163 167 162 159 161 160 156 158 153 157 151 152 155 154 Ref. No. Part No. Description 151 151 151 152 153 X-3380-536-1 X-3380-537-1 X-3380-539-1 3-230-483-01 3-230-482-01 154 155 156 157 158 159 160 161 161 162 162 * 163 * 163 Ref. No. Part No.
CDX-M620/M670 5-5. FRONT PANEL (DSPL) ASSY SECTION 212 211 213 210 207 206 209 205 LCD60 208 214 207 215 204 not supplied (DISPLAY board) 203 #7 202 201 #7 Ref. No. Part No.
CDX-M620/M670 5-6. CD MECHANISM SECTION (1) (MG-383Z-121//K) 252 #8 #8 254 253 257 259 251 266 265 264 256 264 255 255 C 263 M903 261 C 260 #10 258 Ref. No. Part No.
CDX-M620/M670 5-7. CD MECHANISM SECTION (2) (MG-383Z-121//K) 304 301 306 307 307 308 D 314 310 not supplied 312 303 305 313 311 D 309 302 302 302 Ref. No. Part No. Description 301 302 303 304 305 3-040-025-01 3-040-031-01 3-040-056-01 3-040-024-01 3-040-054-01 ARM, CHUCKING DAMPER (T) LEVER (D) RETAINER (DISC) WHEEL (LW), WORM 306 307 3-040-026-01 SPRING (CH), TENSION 3-040-032-01 SPRING (FL), COMPRESSION 62 Remark Ref. No. Part No.
CDX-M620/M670 5-8. CD MECHANISM SECTION (3) (MG-383Z-121//K) 351 M901 (supplied with 351) 352 357 M902 353 358 #11 359 360 354 #8 355 356 361 #8 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No.
CDX-M620/M670 SECTION 6 ELECTRICAL PARTS LIST DISPLAY NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable Ref. No. Part No.
CDX-M620/M670 DISPLAY Ref. No. Part No. Description Remark Ref. No. R72 R73 R74 R76 R77 1-216-811-11 1-216-805-11 1-216-864-11 1-216-841-11 1-216-825-11 METAL CHIP METAL CHIP SHORT METAL CHIP METAL CHIP 150 47 0 47K 2.2K 5% 5% 1/16W 1/16W 5% 5% 1/16W 1/16W C7 C8 C9 C10 R78 R79 R80 R81 R82 1-216-825-11 1-216-825-11 1-216-825-11 1-216-817-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 2.2K 2.
CDX-M620/M670 KEY Ref. No. LSW15 LSW18 LSW20 LSW22 LIMIT SW Part No. Description Remark Ref. No. 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (TA) (AEP,UK,E) 1-771-883-11 SWITCH, TACTILE (WITH LED) (DISC –) 1-771-883-11 SWITCH, TACTILE (WITH LED) (DISC +) 1-771-883-11 SWITCH, TACTILE (WITH LED) (> M) Part No. Description R42 R43 R44 R45 R46 1-216-825-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-025-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 2.2K 2.2K 2.2K 2.
CDX-M620/M670 MAIN Ref. No. Part No. * * * A-3283-172-A MAIN BOARD, COMPLETE (M670:US) A-3283-173-A MAIN BOARD, COMPLETE (M620) A-3283-174-A MAIN BOARD, COMPLETE (AEP,UK,E) ********************* Description Remark * * * * * 3-019-565-01 3-230-509-01 3-230-510-21 3-230-510-31 3-230-513-01 Part No. Description C128 C201 C202 C205 C206 1-125-837-11 1-162-918-11 1-164-156-11 1-164-156-11 1-164-156-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 18PF 0.1uF 0.1uF 0.
CDX-M620/M670 MAIN Ref. No. Part No. Description C306 C307 C308 C309 1-162-965-11 1-162-965-11 1-162-927-11 1-125-837-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP C310 1-164-156-11 CERAMIC CHIP 0.1uF C311 1-125-837-11 CERAMIC CHIP 1uF C312 1-164-156-11 CERAMIC CHIP 0.1uF C313 C314 C315 1-162-927-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP 100PF 0.1uF 0.
CDX-M620/M670 MAIN Ref. No. Part No. Description C407 C451 C452 C454 C455 1-126-572-11 1-124-234-00 1-124-234-00 1-128-057-11 1-124-234-00 ELECT ELECT ELECT ELECT ELECT Remark C456 C457 C501 1-162-974-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP 1-162-968-11 CERAMIC CHIP 0.01uF 0.1uF 0.0047uF 10% C501 1-165-176-11 CERAMIC CHIP 0.047uF C502 1-162-964-11 CERAMIC CHIP 0.
CDX-M620/M670 MAIN Ref. No. Part No. Description D602 D603 D604 D605 D606 8-719-017-95 8-719-422-64 8-719-017-95 8-719-420-51 8-719-988-61 DIODE DIODE DIODE DIODE DIODE MA8180-TX MA8062-M MA8180-TX MA729 1SS355TE-17 Remark Ref. No. Part No. Description Remark J651 D607 D608 D609 D610 D611 8-719-017-95 8-719-988-61 8-719-801-78 8-719-977-12 8-719-977-12 DIODE DIODE DIODE DIODE DIODE MA8180-TX 1SS355TE-17 1SS184 KDZ6.8V (AEP,UK,E) KDZ6.
CDX-M620/M670 MAIN Ref. No. Part No.
CDX-M620/M670 MAIN Ref. No. Part No. Description Remark Part No. Description R347 R348 R349 R350 1-216-864-11 1-216-864-11 1-216-864-11 1-216-833-11 SHORT SHORT SHORT METAL CHIP 0 0 0 10K R351 1-216-833-11 METAL CHIP 10K R352 1-216-835-11 METAL CHIP 15K 5% R353 1-216-822-11 METAL CHIP 1.
CDX-M620/M670 MAIN Ref. No. Part No. Description Remark R389 1-216-829-11 METAL CHIP 4.7K R389 R390 R391 R393 1-216-864-11 1-216-841-11 1-216-821-11 1-216-821-11 0 47K 1K 1K R395 R397 R399 1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-845-11 METAL CHIP 1K 1K 100K 5% 5% 5% R400 1-216-845-11 METAL CHIP 100K 5% R401 1-216-057-00 METAL CHIP 2.
CDX-M620/M670 MAIN Ref. No. SERVO Part No. Description R655 R656 R657 R658 R659 1-216-837-11 1-216-304-11 1-216-839-11 1-216-304-11 1-216-304-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 3.3 33K 3.3 3.3 5% 5% 5% 5% 5% Remark 1/16W 1/10W 1/16W 1/10W 1/10W R660 R661 R662 R701 R702 1-216-809-11 1-216-809-11 1-216-304-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 3.
CDX-M620/M670 SERVO Ref. No. Part No. Description C508 C509 C510 C511 C512 1-164-230-11 1-164-360-11 1-164-217-11 1-164-217-11 1-162-963-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 0.1uF 150PF 150PF 680PF 5% Part No.
CDX-M620/M670 SERVO Ref. No. SUB (CD) SW Part No.
CDX-M620/M670 Ref. No. Part No. Description Remark Ref. No.
CDX-M620/M670 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 78 Date 2001.
