TH R3/Elite User manual V1.
Product Introduction TH R3 Sensor interface On/Off LED indicator (Red) Button Wi-Fi LED indicator (Blue) Auto mode LED indicator(Green) Mounting base Protective cover Sensor interface TH Elite Dry contact interface On/Off LED indicator (Red) Button Wi-Fi LED indicator (Blue) Auto mode LED indicator(Green) LED screen Mounting base Protective cover The device weight is less than 1kg. The installation height of less than 2m is recommended.
LED indicator status instruction LED indicator status Status instruction Blue LED indicator flashes(one long and two short) Pairing mode Blue LED indicator keeps on Device is oline Blue LED indicator quick flashes once Fail to connect to router Blue LED indicator quick flashes twice Connected to router but fail to connect to server Blue LED indicator quick flashes three times Firmware updating Green LED indicator keeps on Auto-mode is on Features TH R3/Elite is a DIY smart switch with temperature
2. Wiring instruction 2-1 Remove protective cover 2-2 L Out L In N N N 100-240V AC L In 2-3 Wiring method of dry contact 9-10mm TH Elite Press the white button on the top of the wire connecting hole to insert the wire corresponding, then release. Dry contact wire conductor size: 0.13-0.5mm², wire stripping length: 9-10mm. Make sure all wires are connected correctly.
3. Insert the sensor Compatible SONOFF sensors: DS18B20, MS01, THS01, AM2301, Si7021. Compatible sensor extension cables: RL560. Some old version sensors need to be used with the accompanying adapter. Device pairing 1. Download the eWeLink App eWeLink eWeLink Android™ & iOS 2. Power on L Out L In N N After powering on, the device will enter the Bluetooth Pairing Mode during the first use. The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
The device will exit the Bluetooth Pairing Mode if not paired within 3mins. If you want to enter this mode, please long press button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release. 3. Add device Method 1: Bluetooth Pairing Add Device All devices Please set device in pairing mode based on user manual and choose the right pairing method.
Alexa voice control instructions 1. Download the Amazon Alexa App and sign up an account. Amazon Alexa 2. Add Amazon Echo Speaker on the Alexa App. 3. Account Linking (Link Alexa account on the eWeLink App) Link with Alexa Profile ① ② LINK ③ ④ 4. After linking the accounts, you can discover devices to connect on the Alexa App according the prompt. Account linking method of Google Assistant, Xiaodu, Tmall Genie, Mate Xiaoai and etc is similar., the guides on the App shall prevail.
Specifications Model THR316, THR320, THR316D, THR320D Input THR316, THR316D:100-240V ~ 50/60Hz 16A Max THR320, THR320D:100-240V ~ 50/60Hz 20A Max Output THR316, THR316D:100-240V ~ 50/60Hz 16A Max THR320, THR320D:100-240V ~ 50/60Hz 20A Max Dry contact output 5-30V，1A Max Wi-Fi IEEE 802.11 b/g/n 2.
Auto mode enable/disable Enable/disable the auto mode by double click the button on the device or enable/disable it on the App directly. Manual control and Auto mode can work at the same time. In the auto mode, you can turn on/off the device manually. After a while, auto mode will resume execution if it detects changes in temperature and humidity. Factory Reset Deleting the device on the eWeLink app indicates you restore it to factory setting. Common Problems Fail to pair Wi-Fi devices to eWeLink APP 1.
The LED indicator flashes twice on repeated means you fail to connect to the server. 1. Make sure the Internet connection is working. You can use your phone or PC to connect to the Internet, and if it fails to access, please check the availability of the Internet connection. 2. Maybe your router has a low carrying capacity. The number of devices connected to the router exceeds its maximum value. Please confirm the maximum number of devices that your router can carry.
