MINI Extreme Wi-Fi Smart Switch ·中 文 ----------1 - 7 · English ----------8 - 14 · Warning ----------15 - 16
产品介绍 按键 网络指示灯 接线端口 设备重量＜1Kg，建议安装高度＜2米。 信号指示灯状态说明 指示灯状态 状态说明 蓝灯呈两短一长闪烁 蓝牙配网模式 蓝色常亮 设备在线 1
功能特点 MINI Extreme紧凑小巧的机身，能够安装在开关暗盒中且最大支持10A负载，使普通开关变为智 能开关。 安全且智能，也可在智能场景中联动其他设备，实现你的家庭自动化。 远程控制 智能定时/延时 语音控制 局域网控制 通电反应 点动模式 智能场景 群组控制 设备安装 1.
2. 接线 1. S1、S2 接或不接开关，设备都可通过自动化或App来控制。 2. 禁止将S1连接零线、地线等强电, 禁止将S2连接火线、零线、地线等强电，以免损坏设备， 造成危险。 3. 确保线路接入无误。 配对至易微联App 1.
2. 上电 通电后，设备首次使用，默认进入蓝牙配网模式。网络指示灯呈“两短一长闪烁”。 10分钟内没有进行配网，设备将退出蓝牙配网模式。 如需再次进入，长按设备按钮5秒直到 网络指示灯呈两短一长闪烁即可。 3.
添加轻智能子设备 进入 eWeLink App 设备设置页面，选择“轻智能子设备”再点击“添加” ，然后触发子设备，即可添 加成功。 设备设置 轻智能子设备 快捷设置 位置管理 分享设备 添加 创建群组 小程序控制 局域网控制 设备设置 轻智能子设备 0/8 网络指示灯 将MINI Extreme安装在暗盒中 5
产品参数 产品型号 MINIR4 输出 100-240V ~ 50/60Hz 10A Max 输入 最大功率 Wi-Fi 工作温度 工作湿度 外壳材料 产品规格 100-240V ~ 50/60Hz 10A Max 2400W IEEE 802.11b/g/n 2.4GHz -10℃-40℃ 5%-95%RH,无冷凝 PC V0 39.5x33x16.8mm 更换设备网络 在 eWeLink App 设备设置界面选择“WiFi设置”进行更换。 恢复出厂设置 在 eWeLink App 端“删除设备” ，设备即恢复出厂设置。 常见问题 1. Wi-Fi设备与易微联App配对失败 1、确保设备进入配对模式.
3、确保Wi-Fi运行在2.4GHz频段。 4、确保正确输入Wi-Fi网络名称和密码，且没有包含特殊字符。 密码错误是常见的配对失败原因。 5、配对时为了确保良好的信号传输，请将设备靠近路由器。 2. LED指示灯连续闪烁两次，服务器连接失败 1、确保网络连接正常。 你可以通过手机或者电脑连接网络。 如果连接失败，请检查网络。 2、路由器承载力较低，连接到路由器的设备超过最大值。 请查看你的路由器可以连接的最大设 备数量。 如果超过最大值，请删除个别设备或者更换一个承载力较高的路由器再次连接。 如果以上方法均无法解决此问题，请在易微联APP上通过“帮助&反馈”提交你的问题。 3.
English Product introduction Button Network indicator Wiring ports The device weight is less than 1kg, and the recommended installation height is less than 2m.
English Features MINI Extreme is compact and tiny enough to be installed in the mounted box, and it supports loads of up to 10A, enable to transform your ordinary switch into a smart switch. Safe and smart, allows you to set smart scenes with other smart devices to automate your home. Remote Control Timer Schedule Voice Control LAN Control Power-on State Inching Mode Smart Scene Group Control Installation 1. Power off Please install and maintain the device by a professional electrician.
English 2. Wiring instruction Before installing the device, please install an air switch as the protective device (Air switch: 10A/250V). 1、No matter S1 and S2 are connected or left idle to the external switch, this device canbe controlled by automation or the App. 2、To avoid damaging the equipment and causing danger, it is forbidden to connect S1 to strong electricity such as neutral wire or earth wire or to connect S2 to strong electricity such as live wire, neutral wire, earth wire and etc.
English 2. Power on After powering on, the device will enter the Bluetooth Pairing Mode defaulted during the first use, and the Network indicator flashes in a cycle of two short and one long. The device will exit the Bluetooth Pairing Mode if not been paired within 10mins. If you want to enter this mode again, please long press the button for 5s until the Network indicator flashes in a cycle of two short and one long and then release. 3.
English Add eWeLink-Remote Sub-devices Enter the Device Settings page on the eWeLink App, select "eWeLink-Remote sub-devices" and tap "Add", then trigger the sub-device to add it successfully.
English Specifications Model MINIR4 Input 100-240V ~ 50/60Hz 10A Max Output 100-240V ~ 50/60Hz 10A Max Max. power 2400W Wi-Fi IEEE 802.11b/g/n 2.4GHz Working temperature -10℃-40℃ Working humidity 5%-95% RH, non-condensing Casing material PC V0 Dimension 39.5x33x16.8mm Device Network Changing Change the device's network by "Wi-Fi Settings" in the "Device Settings" page on the eWeLink App. Factory Reset Reset the device to factory settings by "Delete device" on the eWeLink App.
English 3、Make sure your Wi-Fi works on 2.4GHz band. 4、Make sure to enter the Wi-Fi SSID and password correctly without special characters. Incorrect password is a common cause of pairing failure. 5、To ensure good signal transmission while pairing, please place the device close to the router. 2. The LED indicator flashes twice on repeated means the server fails to connect. 1、Make sure the networking is normal. Check the internet works well by connecting your phone or PC.
Warning FCC Warning Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning IC Warning This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le onjunc areil est conforme aux CNR d’ l’innovation, la science et le développement économique Canada licables aux areils radio exempts de licence.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type MINIR4 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals Operation frequency Range: 2402-2480MHz(BLE) 2412-2472MHz(Wi-Fi) RF Output Power: 2dBm(BLE) 15dBm(802.11b),14dBm(802.11g),15dBm(802.11n20), 16dBm(802.
