Owner's manual

xii
Appendix A - CLI ASCII-Based Interface
• ReadOnlyPassword
Specifies a password which allows only read and no writes. It is
case sensitive, 0 to 32 characters, and cannot contain spaces. An
empty password can be configured by not specifying one.
Default: Password
set ReadOnlyPassword
• ReadOnlyUsername
Specifies the user name which allows only read and no writes.
It is case insensitive, 1 to 32 characters, and cannot contain
spaces.
Default: user
set ReadOnlyUsername [username]
get ReadOnlyUsername
• Reserve (Immediate)
Reports the state of CLI reservation for the current CLI session.
If the command reports that Reservations are enabled, then
another CLI session has control of parameter modification on
the unit.
Reserve
• ResetFCPortErrors
Resets all Fibre Channel error counts for the specified port to
zero.
ResetFCPortErrors [fp | all]
• RestoreConfiguration (Immediate, Disabled on Error)
Use default to force the NVRAM setting to its original defaults.
Use factory to force the NVRAM setting to its original defaults,
including the unit's World Wide Name (WWN). Use saved to
undo any changes made since the last save.
RestoreConfiguration [default | factory | saved]
• RGAddStorage (Immediate)
Adds additional storage to an existing RAID group. Warning:
This feature is not supported under Mac OS X. Up to 10 indices
of available block devices, provided by the BlockDevScan
command, may be added to the RAID group. If this list is
omitted, use RGMemberAdd instead of RGAddStorage. If you
use Commit to automatically save the configuration, all user
data is removed from each new member drive. If you do not
use Commit, you must use the command RGCommit to save
the configuration. If you do not use the Commit parameter
and you have not used RGCommit, you may use the command
RGCancelAddStorage. Note: Mirrors cannot be added to a RAID 4,
RAID 5, RAID 6, or DVRAID RAID group.
RGAddStorage [GroupName] [Mirror | Stripe |
Span] <BlockDevID… <commit>
• Password
Specifies the password used for all sessions: Telnet, FTP and
Sonnet Web Management Tool. Password is case sensitive, from
0 through 32 characters, and cannot contain spaces. Configure
an empty password by pressing Return (Enter) when asked to
designate a new password and confirmation.
Default: Password
set Password
• Performance
Lists performance data for the specified Fibre Channel port
including the average rate (MB/sec.) and number of I/Os
measured over the previous sampling period. Samples are taken
about every second. Successful SCSI Read (08h, 28h) and Write
(0Ah, 2Ah) commands are considered I/Os.
get Performance <fp>
• Ping
Sends an ICMP echo request to the specified host.
ping [mp1] [xxx.xxx.xxx.xxx] <count <size>>
• RAIDRebuildPriority
Sets or displays the RAID rebuild priority. A RAID rebuild
priority set to high gives higher priority to RAID rebuilds and
lower priority to the processing of simultaneous read/write
transactions. A RAID rebuild priority set to low gives lower
priority to the rebuild and a higher priority to read/write
transactions. Set to same, the RAID rebuild and processing of
read/write transactions is the same.
Default: same
set RAIDRebuildPriority <GroupName | all> [high
| low | same]
SaveConfiguration command required
get RAIDRebuildPriority <GroupName | all>
• RAIDSpeedWriteLimit
Specifies or displays the limit on the RAID Speed Write
function. Warning: Changing the default setting (8) may result in
poor performance or timeouts. A lower setting is recommended
when using multiple initiators. A higher setting may improve
performance with multiple streams of sequential write I/O, but
too high a setting will cause timeouts.
Default: 8
set RAIDSpeedWriteLimit [0–256]
get RAIDSpeedWriteLimit