December 16, 2019 2170 - Hedron hedron ™ assembly instructions ©2019 SONNEMAN - A Way of Light Multiple U.S. and foreign patents pending.
December 16, 2019 Hedron™ Product Information and Warnings Important • Always disconnect the power before installing or replacing Luminaires and before cleaning or other maintenance. • Consult a qualified, licensed electrician to ensure correct branch circuit conductor. Consulter un électricien qualifié pour vous assurer que les conducteurs de la dérivation sont adéquats. • Please read all included assembly instructions and warnings carefully before installation.
December 16, 2019 Welcome to Hedron™ A Hedron configuration is built from LED hubs, connecting arms, and cable ceiling hangers. Illumination radiates through either the white optical acrylic lenses, or sparkles with refracted light through micro-faceted clear acrylic crystal lenses. Each hub is a complete LED light engine, using an array of LEDs with driver circuitry on each of the two faces of the hub.
December 16, 2019 C1 (Short) Arms - Multiple boxes 101/2" C C1 (60) 1 s rm A C2 (Long) Arms - Multiple boxes 121/4" C2 (30) C 2 s rm A KEY 6-Way Hub (H6) 5-Way Hub (H5) C1 - 10½” C2 - 12¼” 2 of 13 ©2019 SONNEMAN - A Way of Light
December 16, 2019 Step 1 a. Attach all C1 arms to an H5 Hub, as shown in Fig. 2. Install each Arm into an LED Hub by fully inserting the Arm into a Neck on the Hub (Fig. 1). After each Arm is connected to the Hub, install the M2 Set Screw into the Neck of the Hub, using the Small Hex Wrench provided, and tighten until it comes in contact with the plastic cap on the Arm. DO NOT OVERTIGHTEN THE SCREWS. b. Repeat for all H5 Hubs, including the Powered Hub. Set aside the Powered Hub with Arms for Step 9. c.
December 16, 2019 Step 2 a. Take one of the completed H5 Hubs and attach H6 Hubs onto the end of each arm using one of the necks without a notch. b. Connect the H6 Hubs using C2 Arms as shown in Fig. 4. Note: Make sure the notches on the H6 Hubs are facing each other and not the H5 Hub (see Detailed View). c. Fig. 5 shows this step in the context of the assembly as a whole.
December 16, 2019 Step 3 a. Attach five of the completed H5 Hub clusters to H6 Hubs as shown in Fig. 6. b. Fig. 7 shows this step in the context of the assembly as a whole. Arm Key C1 101/2" (25) Hub Key 5x H5 PWR Fig. 6 IMPORTANT: Be sure to install all M2 Set Screws to secure the Arms to the Hubs, as shown on page 5. Fig.
December 16, 2019 Step 4 a. Attach C2 Arms to remaining open necks in the H6 Hubs. b. Attach H6 Hubs to C2 Arms and adjacent C1 Arms, as shown in Fig. 8. Note: Make sure the notches on the H6 Hubs are facing each other and not the H5 Hub (see Detailed View). c. Fig. 9 shows this step in the context of the assembly as a whole. Arm Length Key C2 121/4" (5) Hub Key 5x H6 Notch Direction IMPORTANT: Be sure to install all M2 Set Screws to secure the Arms to the Hubs, as shown on page 5. Fig.
December 16, 2019 Step 5 a. Attach H6 Hubs to the remaining open C1 Arms using one of the necks without a notch. b. Connect the H6 Hubs to adjacent H6 Hubs with C2 Arms, as shown in Fig. 10. Note: Make sure the notches on the H6 Hubs are facing each other and not the H5 Hub (see Detailed View). c. Fig. 11 shows this step in the context of the assembly as a whole.
December 16, 2019 Step 6 a. Attach five of the completed H5 Hub clusters to H6 Hubs as shown in Fig. 12. b. Fig. 13 shows this step in the context of the assembly as a whole. Arm Key C1 101/2" (25) Hub Key 5x H5 PWR Fig. 12 IMPORTANT: Be sure to install all M2 Set Screws to secure the Arms to the Hubs, as shown on page 5. Fig.
December 16, 2019 Step 7 a. Attach C2 Arms to remaining open necks in the H6 Hubs. b. Attach H6 Hubs to C2 Arms and adjacent C1 Arms, as shown in Fig. 14. Note: Make sure the notches on the H6 Hubs are facing each other and not the H5 Hub (see Detailed View). c. Fig. 15 shows this step in the context of the assembly as a whole. Arm Length Key C2 121/4" (5) Hub Key 5x H6 Notch Direction IMPORTANT: Be sure to install all M2 Set Screws to secure the Arms to the Hubs, as shown on page 5. Fig.
December 16, 2019 Step 8 a. Slide Hanger Clips onto three of the remaining C2 Arms, then use the provided large Hex Wrench to tighten the Screw, as seen in Fig. 19. b. Connect the open H6 hubs using the remaining C2 Arms as shown in Fig. 16. Note: Hanger Clips must be positioned as shown in Fig. 18. c. Fig. 17 shows this step in the context of the assembly as a whole. Arm Length Key C2 121/4" (5) Large Hex Wrench Screw Hang Clip Arm Fig. 19 Fig.
December 16, 2019 Step 9 Outlet Box a. Feed the Cord on the Power Feed Hub through the Bushing on the Power Feed. Adjust the cord length to the desired height, and secure with the Slotted Set Screw using the provided Screwdriver. Reserve excess Cord in the Power Feed. The Power Feed Hub must be a minimum of 12" below the canopy. b. Attach the Mounting Plate to the Outlet Box using the two (2) Outlet Box Screws. c.
December 16, 2019 Step 10 a. Connect the Power Feed Hub cluster as seen in Fig. 21, making sure not to tangle the cords and cable. b. Adjust cables until fixture is level and cord loses its slack but is not taut. c. Restore power to Outlet Box. Arm Key C1 101/2" (5) Hub Key 1x H5 PWR IMPORTANT: Be sure to install all M2 Set Screws to secure the Arms to the Hubs, as shown on page 5. 12 of 13 Fig.
December 16, 2019 COMPLETED ASSEMBLY ©2019 SONNEMAN - A Way of Light 13 of 13
December 16, 2019 Coax Splicing Assembly Instructions INSTRUCTIONS D’INSTALLATION FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID THE WARRANTY Coaxial Power Cord: Outer Braided Conductor Inner Stranded Conductor End View Insulation Outer Jacket If field-cutting is required, please follow the below instructions: 1. Make a 1” slice along the length of the cord's outer jacket (Fig. 1). CAUTION: Do not cut through the outer braided conductor. 2.
