2152 - Aquila Major constellation ™ assembly instructions Multiple U.S. and foreign patents pending.
November 20, 2018 Constellation™ Product Information and Warnings Important • Always disconnect the power before installing or replacing Luminaires and before cleaning or other maintenance. • Consult a qualified, licensed electrician to ensure correct branch circuit conductor. Consulter un électricien qualifié pour vous assurer que les conducteurs de la dérivation sont adéquats. • Please read all included assembly instructions and warnings carefully before installation.
November 20, 2018 Welcome to Constellation™ A Constellation configuration is built from LED hubs, connecting arms, end arms, and cable ceiling hangers. Illumination radiates through either the white optical acrylic lenses, or sparkles with refracted light through micro-faceted clear acrylic crystal lenses. Each hub is a complete LED light engine, using an array of LEDs with driver circuitry on each of the two faces of the hub.
November 20, 2018 Hubs - Contains the LED hubs, arranged by Aquila Major assembly sections and identified with a chart inside the box cover. s hub s hub Power Feed Hub (1) 45° Hub (9) Linear Hub (10) M2 Set Screw (80+) Section Boxes - Organized by assembly section, each box contains various sizes of connecting arms or end arms.
November 20, 2018 REMOTE POWER SUPPLY AND POWER FEED INSTALLATION Outlet Box Remote Power Supply Fig. 1a Remote Power Supply Installation (Fig. 1a): 1. Shut off power to the Outlet Box. 2. Install the Power Supply in a remote and accessible location near the fixture in accordance with local electrical code. Make appropriate electrical connections using wire nuts: a. Connect the Power Supply’s live wire (black) to the live supply wire. b.
November 20, 2018 COMPONENT INSTALLATION INSTRUCTIONS D’INSTALLATION Arm and LED Hub Assembly: 1. Install each Arm into an LED Hub by fully inserting the Arm into a Neck on the Hub (Figs. 2a/2b). 2. After each Arm is connected to the Hub, install the M2 Set Screw into the Neck of the Hub, using the Small Hex Wrench provided, and tighten until it comes in contact with the plastic cap on the Arm. DO NOT OVERTIGHTEN THE SCREWS.
November 20, 2018 OVERVIEW OF ASSEMBLED AQUILA MAJOR Section 1 - page 8 Section 2 - page 9 Section 3 - page 10 Section 4 - page 11 ©2018 SONNEMAN - A Way of Light 7 of 12
November 20, 2018 SECTION 1 a. Build this section using the Hubs labeled Section 1 in the Hubs box, and Connecting Arms from the Section 1 box. b. Start by connecting a C9 Arm to a 45° Hub (1a), and insert into Stay Clip 1 (Fig. 4b), then insert into the Hang Clip and connect to the Power Feed Hub (1b) as shown below (Fig. 4a). Tighten the Hang Clip approx. 4” from the Power Feed Hub. c. Connect the Power Feed Hub to the Power Feed and install per the instructions on page 5. d.
November 20, 2018 SECTION 2 a. Build this section using the 45° Hubs labeled Section 2 in the Hubs box, and Connecting Arms from the Section 2 box. b. Start by connecting the C8 Arm to a Linear Hub (2a) then pass this arm through Stay Clip 2 (Fig. 5a), refer to Stay Clip instructions on page 6, and continue by connecting a Linear Hub (2b) and a C4 Arm. c. Continue adding Hubs and Arms following the order and pattern in Fig. 5a, and complete this Section by connecting a C4 Arm to 45° Hub (1d) on Section 1.
November 20, 2018 SECTION 3 a. Build this section using the 45° Hubs labeled Section 3 in the Hubs box, and Connecting Arms from the Section 3 box. b. Start by connecting the E6 Arm to a Linear Hub (3a) then pass this arm through Stay Clip 1 until the arm end is approx. 2” from the clip (Fig. 6b), refer to instructions on page 6. Continue by connecting a C9 Arm to the Linear Hub (3a), followed by a 45° Hub (3b). c. Add the remaining Arms and Hubs following the order and pattern in Fig.
November 20, 2018 ADDING THE END ARMS (Section 4) a. Build this section using the End Arms from the Section 4 box. b. Refer to the illustration below (Fig. 7) to secure each of the End Arms, there is no specific order for installing these. IMPORTANT: Be sure to install all M2 Set Screws to secure the Arms to the Hubs, as shown on page 6. Arm Length Key E1 2½" (7) E2 4½" (6) E3 6½" (4) E4 8½" (1) E5 10½" (1) E4 E5 E1 E3 Fig.
November 20, 2018 COMPLETED ASSEMBLY 12 of 12 ©2018 SONNEMAN - A Way of Light
