General Guidelines Please read the following instructions carefully and use the product accordingly. Please keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed. Notes Personal injury and/or damage to the product may scour if products are used outside of their intended purposes and/or if products have been changed/modified from their original design.
A (1) Main Umbrella Plastic Water Tillable Stand C(1) Swivel Mechanism Base Pole E (1) Swivel Cover F — (1) Allen Wrench Stainless Bolt (M8 x0.63IN Washer 1(1) Threaded Knob J(1) Crank Handle K(1) Umbrella Cover L(1) Connector CE ) rms) Lower Pols N (1) Solar Panel SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble or install the product. = Assemble on level ground. » Keep children away from assembly area. «Two adults are required for safe assembly.
Carefully check all packaging materials before discarding. Do not assemble if there are missing pieces. Step 1 Place the stand (part B) on a level ground where you intend to locate your umbrella. Open the cap on the top of the stand and fill the stand with water. Then tighten the cap. The stand is quite heavy when filled with water (220lbs) . In case you want to move the stand, open the cap on the side of the stand and release the water first.
Step 3 Attach the Base Pole (part D) on top of the Swivel Mechanism (part C) with bolts (part G2), washers (part H), and Allen wrench (part F). Important Notice : Pay attention to the size of the middle hole in the Swivel Cover (part E). Side Ais 1.6” and Side Side B on the Swivel Cover (part E) and the locking hole on the Base Pole (part D) must be on the same side.
bel Step 5 Place the lower pole ( part M) on the base as sector ( part L ) on the top of the lower pole ( part the sam the two holes are on M) .
Step 7 Attach the Solar Panel ( part N) on the top of Main Umbrella ( part. 5 ~ Firmly, but carefully, connect the plug on the solar panel with the socket on the top of the umbrella. Do not pull on wires as doing so may permanently damage the connections. Before the first use, ensure the solar panel receives at feast 8 hours of direct sunlight to charge the batteries. Align the notches on the solar panel with the grooves on thirtieth of the umbrella, hide the plug and wires inside the hollow space.
Step 9 Insert the Crank Handle {part J} into the square hole on the Main Umbrella (part A). Screw the Threaded Knob (part |) into the locking hole on the Main Umbrella (part A). ATTENTION: MAKE SURE ALL BOLTS AND SCREWS ARE FULLY TIGHTENED BEFORE USING THE UMBRELLA.
Step 10 Squeezing the trigger before attempting to raise the crank house. Turn the Crank Pp handle clockwise to extend the umbrella fully. 10 0} Press the light switch on the rib end to turn the solar lights on / off .
Step 11 The umbrella has 6 position holes on the main pole to lock the canopy at different angles.
Step 12 Squeeze the trigger before attempting to lower the crank house. Tums the Crank handle counter-clockwise to close the umbrella. This umbrella has a 360 degree swivel mechanism . Before attempting Step 13 to turn the umbrella, close the umbrella first and press the lever down with your foot to release the mechanism.
BATTERY REPLACEMENT Charge the batteries in the solar panel every year of when the light output is diminished. « Only install new batteries: of the same type info the product; Ni-MG 2000mAh rechargeable batteries: « Failure: to insert batteries in the comet polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause batteries to leak. + Do not rx old and new batteries, +» Do rot mix Alkaline, Nicks Cadmium or Lithium rechargeable batteries.
