Manual
Table Of Contents
- Fig A: Packing List
- Fig B: Power Connections
- Fig C: Mains Lead Table
- Fig 1-1: RB-2S4 Reference Monitor Front Panel
- Fig 1-2: RB-2S10 Reference Monitor Front Panel
- Fig 1-3: Reference Monitor Block Diagram
- Fig 1-4: RM-2S4 Front Panel Controls
- Fig 1-5: RM-2S10 Front Panel Controls
- Fig 1-6: RM-2S4 Source Selector
- Fig 1-7: RM-2S10 Source Selector
- Fig 1-8: RM-2S4 & RM-2S10 Meters
- Fig 1-9: RM-2S4 & RM-2S10 DIPSwitch Settings
- Fig 1-10: Meter Labelling Options
- Fig 1-11: Brightness Control
- Fig 1-13: Balance Control
- Fig 1-12: Phase Meter Display
- Fig 1-14: Status LEDs
- Fig 1-15: RB-2S4 & RB-2S10 Modifier Switches
- Fig 1-16: Reference Monitor RM-2S4 Rear
- Fig 1-17: Reference Monitor RM-2S10 Rear
- Fig 1-18: RM-2S4 & RM-2S10 DIPswitch Settings
- Fig 2-1: RB-4C8 Reference Monitor Front Panel
- Fig 2-2: Reference Monitor Block Diagram
- Fig 2-3: RM-4C8 Front Panel Controls
- Fig 2-4: RM-4C8 Rotary Source Selectors
- Fig 2-5: RM-4C8 Meters
- Fig 2-6: RM-4C8 DIPSwitch Settings
- Fig 2-7: Meter Labelling Options
- Fig 2-8: Brightness Control
- Fig 2-9: Phase Meter Display
- Fig 2-10: Balance Control
- Fig 2-11: Status LEDs
- Fig 2-12: RB-4C8 Modifier Switches
- Fig 2-13: Reference Monitor RM-4C8 Rear
- Fig 3-1: RM-HD1 Expansion Card
- Fig 3-2: RM-HDE1 Expansion Card
- Fig 3-3: Reference Monitor RM-HD(E)1 Block Diagram
- Warranty
- Safety Information
- Installation Information
- Reference Monitors Introduction
- RM-2S4 Reference Monitor, 2 LED meters & 4 stereo
- channel inputs
- RM-2S10 Reference Monitor, 2 LED meters & 10 stereo
- channel inputs
- Technical Specification RM-2S4 & RM-2S10
- RB-4C8 Reference Monitor, 4 LED meters, 8 channel inputs &
- dual selectors
- Technical Specification RM-4C8
- RM-HD1 Reference Monitor HD-SDI Expansion Card &
- RM-HDE1 Reference Monitor HD-SDI & Dolby E Expansion Card
- Technical Specification RM-HD1 & RM-HDE1
- Serial Interface Commands & Responses Protocol
48
Reference Monitors User Handbook
REFERENCE MONITORS RM-4C8
2
REFERENCE MONITORS RM-HD(E)1
48
Reference Monitors User Handbook
REFERENCE MONITORS RM-HD(E)1
3
Technical Specication RM-HD1 & RM-HDE1
SDI Input
SDI Video: SMPTE 259M – SD @ 270 Mbps or
SMPTE 292M – HD @ 1.5 Gbps
Input Impedance: 75Ω
SDI Output
SDI Video: Reclocked input
Output Impedance: 75Ω
Output Level: 0.8 Vp-p
Return Loss: > 15 dB (1.5 GHz)
Jitter: < 0.2UI
Embedded Audio
Standard: SMPTE 272M or SMPTE 299M 24 bit 48 kHz synchronous/
asynchronous*
*Audio must be synchronous in SD. If asynchronous audio
is presented in an HD input then only one group can be
presented at any one time.
Connectors
HD-SDI Input: 1 x BNC 75Ω SDI input
HD-SDI Output: 1 x BNC 75Ω SDI output (reclocked loop through)
Equipment Type
RM-HD1: HD-SDI expansion card
RM-HDE1: HD-SDI & Dolby E Decoder expansion card
Physical Specication
Dimensions (Raw): 15cm (W) x 11.5cm (D) x 3.1cm (H)
5.9” (W) x 4.5” (D*) x 1.2” (H) (1U)
Dimensions (Boxed): 25cm (W) x 20cm (D) x 10cm (H)
9.8” (W) x 7.9” (D*) x 3.9” (H) (1U)
Weight (RM-HD1): Nett: 0.13kg Gross: 0.4kg
Nett: 0.3lb Gross: 0.9lb
Weight (RM-HDE1): Nett: 0.15kg Gross: 0.4kg
Nett: 0.3lb Gross: 0.9lb