Manual
Table Of Contents
- Fig A: Packing List
- Fig B: Power Connections
- Fig C: Mains Lead Table
- Fig 1-1: RB-2S4 Reference Monitor Front Panel
- Fig 1-2: RB-2S10 Reference Monitor Front Panel
- Fig 1-3: Reference Monitor Block Diagram
- Fig 1-4: RM-2S4 Front Panel Controls
- Fig 1-5: RM-2S10 Front Panel Controls
- Fig 1-6: RM-2S4 Source Selector
- Fig 1-7: RM-2S10 Source Selector
- Fig 1-8: RM-2S4 & RM-2S10 Meters
- Fig 1-9: RM-2S4 & RM-2S10 DIPSwitch Settings
- Fig 1-10: Meter Labelling Options
- Fig 1-11: Brightness Control
- Fig 1-13: Balance Control
- Fig 1-12: Phase Meter Display
- Fig 1-14: Status LEDs
- Fig 1-15: RB-2S4 & RB-2S10 Modifier Switches
- Fig 1-16: Reference Monitor RM-2S4 Rear
- Fig 1-17: Reference Monitor RM-2S10 Rear
- Fig 1-18: RM-2S4 & RM-2S10 DIPswitch Settings
- Fig 2-1: RB-4C8 Reference Monitor Front Panel
- Fig 2-2: Reference Monitor Block Diagram
- Fig 2-3: RM-4C8 Front Panel Controls
- Fig 2-4: RM-4C8 Rotary Source Selectors
- Fig 2-5: RM-4C8 Meters
- Fig 2-6: RM-4C8 DIPSwitch Settings
- Fig 2-7: Meter Labelling Options
- Fig 2-8: Brightness Control
- Fig 2-9: Phase Meter Display
- Fig 2-10: Balance Control
- Fig 2-11: Status LEDs
- Fig 2-12: RB-4C8 Modifier Switches
- Fig 2-13: Reference Monitor RM-4C8 Rear
- Fig 3-1: RM-HD1 Expansion Card
- Fig 3-2: RM-HDE1 Expansion Card
- Fig 3-3: Reference Monitor RM-HD(E)1 Block Diagram
- Warranty
- Safety Information
- Installation Information
- Reference Monitors Introduction
- RM-2S4 Reference Monitor, 2 LED meters & 4 stereo
- channel inputs
- RM-2S10 Reference Monitor, 2 LED meters & 10 stereo
- channel inputs
- Technical Specification RM-2S4 & RM-2S10
- RB-4C8 Reference Monitor, 4 LED meters, 8 channel inputs &
- dual selectors
- Technical Specification RM-4C8
- RM-HD1 Reference Monitor HD-SDI Expansion Card &
- RM-HDE1 Reference Monitor HD-SDI & Dolby E Expansion Card
- Technical Specification RM-HD1 & RM-HDE1
- Serial Interface Commands & Responses Protocol
16
Reference Monitors User Handbook
REFERENCE MONITORS RM-2S4 & RM-2S10
REFERENCE MONITORS RM-2S4 & RM-2S10
1
SW1: When set to ON, digital input 1 is terminated with 110Ω.
SW2: When set to ON, digital input 2 is terminated with 110Ω.
SW11: When set to ON, digital input 3 is terminated with 110Ω.
SW12: When set to ON, digital input 4 is terminated with 110Ω.
Audio Inputs (RM-2S10)
Three 25-pin female D-type connectors are provided for the simultaneous connection of
up to ten stereo analogue (BANK ANA) and ten stereo AES/EBU digital (BANK DIG) audio
sources. The pin assignations are as follows:
Pin No. Function
(BANK DIG 1-10)
Function
(BANK ANA 1-5)
Function
(BANK ANA 6-10)
1 AES/EBU Input 1+ Analogue Input 1L+ Analogue Input 6L+
14 AES/EBU Input 1- Analogue Input 1L- Analogue Input 6L-
2 Ground Ground Ground
15 AES/EBU Input 2- Analogue Input 1R- Analogue Input 6R-
3 AES/EBU Input 2+ Analogue Input 1R+ Analogue Input 6R+
16 AES/EBU Input 3+ Analogue Input 2L+ Analogue Input 7L+
4 AES/EBU Input 3- Analogue Input 2L- Analogue Input 7L-
17 Ground Ground Ground
5 AES/EBU Input 4- Analogue Input 2R- Analogue Input 7R-
18 AES/EBU Input 4+ Analogue Input 2R+ Analogue Input 7R+
6 AES/EBU Input 5+ Analogue Input 3L+ Analogue Input 8L+
19 AES/EBU Input 5- Analogue Input 3L- Analogue Input 8L-
7 Ground Ground Ground
20 AES/EBU Input 6- Analogue Input 3R- Analogue Input 8R-
8 AES/EBU Input 6+ Analogue Input 3R+ Analogue Input 8R+
21 AES/EBU Input 7+ Analogue Input 4L+ Analogue Input 9L+
9 AES/EBU Input 7- Analogue Input 4L- Analogue Input 9L-
22 Ground Ground Ground
10 AES/EBU Input 8- Analogue Input 4R- Analogue Input 9R-
23 AES/EBU Input 8+ Analogue Input 4R+ Analogue Input 9R+
11 AES/EBU Input 9+ Analogue Input 5L+ Analogue Input 10L+
24 AES/EBU Input 9- Analogue Input 5L- Analogue Input 10L-
12 Ground Ground Ground
25 AES/EBU Input 10- Analogue Input 5R- Analogue Input 10R-
13 AES/EBU Input 10+ Analogue Input 5R+ Analogue Input 10R+