Manual
Table Of Contents
- Analogue Redbox User Handbook rev 1.92
- Contents
- Figures
- Warranty, Safety & Installation Information
- RB-MA1 Single & RB-MA2 Dual Microphone Amplifiers
- RB-SM1 Single & RB-SM2 Dual Stereo To Mono Converter
- RB-UL1 Single, RB-UL2 Dual & RB-UL4 Quad Stereo Unbalanced
- RB-LU4 Quad Stereo Balanced To Unbalanced Converter
- RB-BL2 Single & RB-BL4 Dual Bi-Directional Matching Converte
- RB-SL2 Twin Mono, or Stereo, Limiter
- RB-DA6 6 Way Stereo Distribution Amplifier
- RB-HD1 Stereo Headphone Amplifier
- RB-HD6 6 Way Stereo Headphone Distribution Amplifier
- RB-SD1 Silence Detection Unit
- RB-PMX4 10 Input, 4 Output Analogue Preset Mixer
- RB-LI2 Stereo Line Isolation Unit
- RB-PLI6 6 Way Mono Passive Line Isolation Unit
- RB-SS10 10 Way Stereo Analogue Source Selector/Mixer
- RB-LC3 3 Way Light/Power Controller
- Glossary
- Connectors And Cabling
- Index
Chapter 15 - RB-LC3 3 Way Light/Power Controller
15-4 Redbox User Handbook
15.3.4. Configuration Switches
The configuration switches are used to set the flash mode for each output separately.
The selections allow the outputs to be controlled by a remote input, a telephone call,
or a combination of remote inputs, say, for example to control 2 lights such as
“Rehearsal” and “Live”, using Settings 10-13.
The configuration switches are also used to select the operating mode, either latching
or momentary, for each output. The operating mode is set when power is applied to
the unit and the configuration switches are set to either Setting 15 or 16. The Output
will flash once to indicate latching mode has been selected or twice to indicate
momentary mode has been selected. The configuration switches can then be returned
to the required Setting. In Latching Mode (Setting 15 selected on power up), the
Output is On/Flashing only while the selected Remote Inputs remain asserted. In
Momentary Mode (Setting 16 selected on power up), each separate assertion of the
selected Remote Inputs changes the state of the Output. For example: for setting 4,
the first assertion of Remote 1 switches Output 1 on. The second assertion of Remote
1 switches Output 1 off. The operating mode has no effect when using Settings 1-3.
The available settings for output 1, configured using switches Sw1 to Sw4, are
detailed below:
Fig 15-4: Output 1 Configuration Setting
Setting
No
Sw1 Sw2 Sw3 Sw4 Description
1 Off Off Off Off Flash Output 1 when telephone rings
Output 1 On when telephone is off-hook
2 On Off Off Off Output 1 On when telephone is off-hook
3 Off On Off Off Flash Output 1 when telephone rings
4 On On Off Off Output 1 On when Remote 1 asserted
5 Off Off On Off Output 1 On when Remote 2 asserted
6 On Off On Off Output 1 On when Remote 3 asserted
7 Off On On Off Flash Output 1 when Remote 1 asserted
8 On On On Off Flash Output 1 when Remote 2 asserted
9 Off Off Off On Flash Output 1 when Remote 3 asserted
10 On Off Off On Output 1 On when Remote 1 or Remote 2
asserted
11 Off On Off On Output 1 On when Remote 1 asserted and
Remote 2 not asserted
12 On On Off On Output 1 On when Remote 1 not asserted
and Remote 2 asserted
13 Off Off On On Output 1 On when Remote 1 asserted and
Remote 2 asserted
14 On Off On On Reserved for future assignment
15 Off On On On Latching Mode selection for Output 1
16 On On On On Momentary Mode selection for Output 1