Handbook

SignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED SIGNS
SIGNALLED STUDIO ILLUMINATED SIGNS
SignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED SIGNS
SIGNALLED STUDIO ILLUMINATED SIGNS
76
Note: a reasonable amount of force is needed to fully connect the LED sign assembly to the
wall plate.
The sign can be removed from the wall mount plate by holding around the end moulding,
as close to the wall as possible, and pushing up on the sign until the retaining pins unclip.
This will take more force to achieve than when tting the sign.
Note: do not clip and unclip the sign repeatedly as this can damage the retaining pins and
cause the sign to be a loose t on the wall mount plate.
LD-KE1 SignalLED Conversion Kit, Single Flush Mount to End Mount
To convert the LD-20F & LD-40F style ush mount single sided signs into single sided end
mount signs you will need to t the LD-KE1 conversion kit. Please follow these instructions
carefully.
Note: You’ll need the following tools to use the conversion kit:, a No. 0 and No.1 Pozi-drive
screwdriver.
Take care not to damage the clear surface of the sign board. The surface will be marked by
swarf or rough surfaces, so please use a clean cloth to hold the sign.
Because the sign is single sided the text will only be correctly viewable from one side. If the
UFYUNVTUCFWJFXFEGSPNPOFQBSUJDVMBSTJEFUIJTNVTUCFDIPTFOJOJUJBMMZBTJUXJMMBòFDUUIF
disassembly and subsequent re-assembly of the sign
As standard the SignalLED PCB is tted into the right hand end of the LD-20F & LD-40F (see
Fig 9). If you would like the sign to be viewable with the right hand side of the sign mounted
onto the wall please use the ‘Right Hand Side’ tting instructions.
If you would like the sign to be viewable with the left hand side of the sign mounted onto
the wall, please use the ‘Left Hand Side’ tting instructions.
Fig 9: Sign Components to be Converted
Right Hand Side Fitting of the Conversion Kit
1) Open the end cover on the left hand ush mount assembly by removing the self
tapping screw with a No.1 pozi-drive screwdriver.
2) Remove the left hand ush mount assembly by unscrewing the 4 screws that x the
end moulding to the aluminium tube. These are located inside at the bottom of the
end moulding. See Fig 11.
3) Align the 4 pins of the extrusion end cover with the screw holes in the exposed end
of the aluminium tube. Note the orientation of the cut-out with the clear sign board
and press t the end cover fully onto the aluminium tube.
4) Open the end cover on the right hand ush mount assembly by removing the self-
tapping screw with a No.1 pozi-drive screwdriver.
5) Remove the ush wall mount moulding from the end moulding by unscrewing the 4
screws visible under the cover See Fig 12.
6) Fit the internal hanger plate into the end wall mount moulding. Align the semi-
circular cut-out in the hanger plate with the raised section above the serial number
label, which indicates the bottom of the assembly. Also make sure that the hanger
plate ts into the slots in the wall mount moulding.
7) This combination is then xed to the right hand ush mount assembly end moulding
with the 4 supplied No.4 x ¾ self tap screws. See Fig 13. Do not substitute any other
screws in these positions and do not reuse the screws removed from these positions,
because they will not support the sign correctly.
8) Please refer to the installation notes for the LD-40E style signs to complete the nal
tting and colour/conguration set-up.
Fig 10: Kit Components Used for the Conversion Fig 11: Removing the Left Hand Assembly