Handbook

SignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED SIGNS
SIGNALLED STUDIO ILLUMINATED SIGNS
SignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED SIGNS
SIGNALLED STUDIO ILLUMINATED SIGNS
310
There is a 3 step procedure to congure the sign for each particular input state, e.g. if
you want to set the sign to be a certain colour when signalling input 1 is used and then
to change colour when signalling input 2 is used, then you’ll need to go through this
procedure twice.
Important Note: If you are using a twin sign with signalling input 1 to control one side of the
sign and signalling input 2 to control the other side of the sign, you need to run through this
procedure three times:
1. To dene what happens when signalling input 1 is used.
2. To dene what happens when signalling input 2 is used.
3. To dene what happens when signalling inputs 1 & 2 are both used at the same time.
*OUIF4JHOBM-&%UIJTJTUSFBUFEBTBEJòFSFOUQSPHSBNNBCMFTUBUFBOETPJGZPVXBOUUIF
signs to react normally, this procedure would use the Follow Mode when conguring the
illumination modes.
1. Setting the Colour of Your Sign
B&OTVSFBMMUIFTXJUDIFTBSFTFUUPUIF0òQPTJUJPO
b) Set switches 2 and 3 to select the relevant input state, e.g. if you want to use Signalling
JOQVUUPDPOUSPMUIFTJHOUIFOTFUUIF485UP0OBOE485UP0ò
Function SWT2 SWT3
Program resting state (when no signalling inputs are active) 0ò 0ò
Signalling Input 1 active state On 0ò
Signalling Input 2 active state 0ò On
Signalling Input 1 and Input 2 active state On On
c) Set SWT 4 On to indicate that you are about to set the colour.
d) Set SWT 5 to 8 as follows:
Colour SWT5 SWT6 SWT7 SWT8
0ò 0ò 0ò 0ò 0ò
Red On 0ò 0ò 0ò
Green 0ò On 0ò 0ò
Blue On On 0ò 0ò
Cyan 0ò 0ò On 0ò
Magenta On 0ò On 0ò
Yellow 0ò On On 0ò
White On On On 0ò
Orange 0ò 0ò 0ò On
Dual colour mode* On On On On
*Note: Dual colour mode can be assigned when both inputs are active - it will illuminate
the two halves of the sign according to the colours set for input 1 and input 2 modes.
F4FU4850OBOESFUVSOJUUP0òUIJTTBWFTUIFDPMPVS
Sign Dimensions & Mounting Positions
The SignalLED sign consists of an aluminium centre section with plastic end mouldings
for each of the signs. The end mounting signs are fastened to a secure surface using a
slotted wall mount plate that locates into another hanger plate mounted in the SignalLED
assembly. The dimensions for the LED signs below include the mouldings and trim. Please
note that the mounting sizes are for reference only and should be checked with your
particular sign.
Fig 1: LD-40E1 Style Sign Dimensions (mm)
Fig 2: LD-40E1 Style Mounting Fig 3: Cable Routing Cut-Outs
Hole Positions (mm)
Mounting & Connecting The LD-40E1 Style Sign
The LED sign should be mounted on a at and rm solid surface. To assist the correct
mounting the sign is supplied with a mounting kit comprising 2 x wall plugs (for mounting
into brick, concrete, breeze block or stone) and 2 x large ange screws.
Note: You’ll need the following tools to mount the sign: an electric drill tted with a 6mm
diameter masonry drill bit, a No.1 Pozi-drive screwdriver and a spirit level.