Handbook

SignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED SIGNS
SIGNALLED STUDIO ILLUMINATED SIGNS
SignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED SIGNS
SIGNALLED STUDIO ILLUMINATED SIGNS
112
Warranty Information
This product is supplied with a 12 month back to base warranty. For further details, please
refer to the Sonifex website: http://www.sonifex.co.uk/company/terms/index.shtml
In order to register the date of purchase so that we can keep you informed of any design
improvements or modications, it is important to complete the warranty registration
document that is enclosed and return it to Sonifex Ltd in the UK.
For your own records you should write down the serial number of the SignalLED sign.
Serial Number TL………………………………………
Introduction
The SignalLED Sign is a new elegant approach to illuminated displays and signage. Using
the latest technology and components, the SignalLED sign can be simply congured onsite
for colour and mode.
t $IPPTFGSPNXIJUFHSFFOSFECMVFZFMMPXPSBOHFDZBOBOENBHFOUB
t $IPPTFGSPNBMBSHFSBOHFPGEJòFSFOUTJHOUFYU
t 'PVSJMMVNJOBUJPONPEFTDPOTUBOUøBTIJOHQVMTJOHBOEPò
t 5XPDPOUSPMQVMMMPXJOQVUT
t 4JOHMFPSUXJOTJHOTXJUITFQBSBUFDPOUSPMT
t %$JOQVUQPXFSTVQQMZQSPWJEFE
t 'MVTIUPUIFXBMMPSFOENPVOUFE
t %PVCMFTJEFEFOENPVOUJOHBWBJMBCMFGPSVTFJODPSSJEPST
t 4JNQMFUPJOTUBMM
t $VTUPNTJHOTDBOCFNBEFUPPSEFS
Safety Information
This equipment has been designed to meet the safety regulations currently advised
in the country of purchase and it conforms to the safety regulations specied by use
of the CE Mark. This equipment operates in a horizontal position.
Installation Notes
The SignalLED sign should be installed in an area which is not subject to excessive heat or
cold. Also, you should avoid installing it in atmospheric conditions which are dusty, smoky,
or dirty, or where there is moisture or vibration. The sign is for internal use only. The unit is
not sealed and cannot be used outside or in very damp or humid environments.
Do not use any solvents to clean the sign. Use a soft dry brush or a clean cloth moistened
with water or mild detergent.
Avoid using the SignalLED sign close to strong sources of electromagnetic radiation such as
video monitors or high power electric cabling.
In all cases the SignalLED sign should be installed and serviced by qualied personnel.
2. Setting Which Side (Segment) of Your Sign Illuminates
B&OTVSFBMMUIFTXJUDIFTBSFTFUUPUIF0òQPTJUJPO
b) Set SWT 2 and 3 to modify the relevant input state:
Function SWT2 SWT3
Program resting state (when no signalling inputs are active) 0ò 0ò
Signalling Input 1 active state On 0ò
Signalling Input 2 active state 0ò On
Signalling Input 1 and Input 2 active state On On
c) Set SWT 6 to 8 as follows:
Side (Segment) SWT6 SWT7 SWT8
Master (section of the sign nearest the
connection block)
0ò 0ò 0ò
Slave (section of the sign furthest from the
connection block)
On 0ò 0ò
Whole Sign 0ò On 0ò
E4FU4850OBOESFUVSOJUUP0òUIJTTBWFTUIFTJEFPSTFHNFOU
3. Setting the Illumination Mode of Your Sign
B&OTVSFBMMUIFTXJUDIFTBSFTFUUPUIF0òQPTJUJPO
b) Set SWT 2 and 3 to modify the relevant input state:
Function SWT2 SWT3
Program resting state (when no signalling inputs are active) 0ò 0ò
Signalling Input 1 active state On 0ò
Signalling Input 2 active state 0ò On
Signalling Input 1 and Input 2 active state On On
c) Set SWT 5 to On to indicate that you are about to set the Mode.
d) Set SWT 6 to 8 as follows:
Illumination Mode SWT6 SWT7 SWT8
On constantly 0ò 0ò 0ò
Flashing On 0ò 0ò
Pulsing 0ò On 0ò
Follow mode** On On On
**Note: Follow mode can be assigned when both inputs are active. It will illuminate the
two halves of the sign according to the modes set for input 1 and input 2.
F4FU4850OBOESFUVSOJUUP0òUIJTTBWFTUIFJMMVNJOBUJPONPEF