User Guide

ManualsBrandsSonic Alert ManualsOtherSBB500SS

SBB500SS Sonic Bomb Loud Dual Alarm Clock

Instruction Manual

Special Features of Your Sonic Boom Alarm Clock

Congratulations on the purchase of your Sonic Boom Alarm Clock! This unique clock

allows you to:

• Wake up to any combination of loud pulsating audio alarm, flashing lights, and

shaking bed (bed vibrator sold separately).

• Adjust the alarm volume and tone to achieve the most effective audio alert.

• Easily view the large, bright green LED display with adjustable display angle.

• Save your time and alarm setting in the event of a power interruption through the

use of a battery backup (9V battery not included).

• Use the clock with Sonic Alert’s complete line of signaling products, such as

telephone, doorbell, and baby cry signalers.

Setting the Time of Day

Note: Since your clock has a 24-hour memory, you must make sure that the time set is

AM or PM. A round light in the upper left of the clock display will indicate PM time.

For AM time, the light does not appear.

1. Press and hold the TIME (time set) button. Then press the HOUR button until the

correct hour is shown.

2. Press and hold the TIME button again. Then press the MIN (minute) button until

the correct minutes are shown.

Setting an Alarm Time

Note: Since your clock has a 24-hour memory, you must make sure that the time set is

AM or PM. A round light in the upper left of the clock display will indicate PM time.

For AM time, the light does not appear.

Summary of content (5 pages)

PAGE 1
SBB500SS Sonic Bomb Loud Dual Alarm Clock Instruction Manual Special Features of Your Sonic Boom Alarm Clock Congratulations on the purchase of your Sonic Boom Alarm Clock! This unique clock allows you to: • Wake up to any combination of loud pulsating audio alarm, flashing lights, and shaking bed (bed vibrator sold separately). • Adjust the alarm volume and tone to achieve the most effective audio alert. • Easily view the large, bright green LED display with adjustable display angle.
PAGE 2
1. Press and hold the ALARM (alarm set) button. Then press the HOUR button until the desired alarm hour is shown. 2. Press and hold the ALARM button again. Then press the MIN (minute) button until the desired alarm minutes are shown. Turning the Alarm On and Choosing Waking Options The Sonic Boom clock can wake you with any combination of flashing lamp, pulsating audio alarm, and shaking bed. To turn on the alarm, you must set the OUTLETS switch to the LAMP, VIB (vibrator), or BOTH positions.
PAGE 3
Using the Volume and Tone Controls You use the VOLUME control knob to turn the audio alarm on or off and to adjust the volume. To increase volume, rotate the knob toward you. To turn the audio alarm off, rotate the knob away from you until you feel it click. You use the TONE control knob to adjust the pitch of the audio alarm. For a lower pitch alarm, rotate the knob toward you. For a higher pitch, rotate it away from you.
PAGE 4
To install a battery, use a small screwdriver or key to remove the battery compartment access door from the bottom of the clock. Once you’ve installed the battery, the cover clips back into place. Note: During a power interruption, the clocks display will turn off, but time and alarm settings will be saved. Using a Lamp With the Alarm Clock To use a lamp that is connected to the Sonic Boom alarm clock, follow these steps: 1. Plug the lamp into the AC outlet on the back of the clock. 2.
PAGE 5
Sonic Alert offers a number of transmitters that work with the clock’s remote receiver, including: • DS 700 Doorbell Signaler • TR 75 Telephone Signaler • BC 400 Baby Cry Signaler To turn the clock’s remote receiver on for use with a remote transmitter, locate the RECEIVER ON/OFF switch on the bottom of the clock and set it to the ON. If you are not using any Sonic Alert remote transmitter or if you do not want the clock to respond to a transmitter, set the switch to OFF.