Datasheet

MPI-520
Index: WMGBMPI520
MULTIFUNCTION ELECTRICAL
INSTALLATIONS METER
MULTIFUNCTION ELECTRICAL
INSTALLATIONS METER
WAADAWS03
WAPRZ1X2YEBB
WAPRZ1X2BUBB
WAPRZ1X2REBB
WAPRZ030REBBSZ
WAPRZ015BUBBSZ
WAPRZUSB
WASONYEOGB1
WASONREOGB1
WASONBUOGB1
WAKROYE20K02
WAKRORE20K02
WASONG30
WAFUTL1
WAPOZSZEKPL
WAPOJ1
Standard accesories of the meter MPI-520:
- probe with START button with
UNI-SCHUKO (WS-03)
- test lead with banana plug; 1,2m; yellow
- test lead with banana plug; 1,2m; blue
- test lead with banana plug; 1,2m; red
- test lead on a reel with banana plugs;
30m; red
- test lead on a reel with banana plugs;
15m; blue
- USB transmission cable
- pin probe with banana connector; yellow
- pin probe with banana connector; red
- pin probe with banana connector; blue
- crocodile clip K02; yellow
- crocodile clip K02; red
- earth contact test probe (rod); 0,3m
- carrying case L1
- hanging straps
- battery case LR14 (size C)
- batteries
- calibration certificate issued
by calibration laboratory
- test lead with banana plug 5m; red
- test lead with banana plug 10m; red
- test lead with banana plug 20m; red
- cable for battery charger
- lead for battery loading from the socket
of car lighter (12V)
- AC line splitter (AC-16)
- triple phase socket adapter AGT-16P
- triple phase socket adapter AGT-32P
- triple phase socket adapter AGT-63P
- adapter AUTO-ISO-1000C
- RCD breaker testing adapter TWR-1
universal pin
- probe with UNI-SCHUKO (WS-04)
- earth contact test probe (rod); 0,8m
- carrying case L3
- round connector current
clamps C3 ( mm)
- Ni-MH battery package 4,8V 4,2Ah
- crocodile clip K02; blue
- cramp
- test wire reel
- power supply adaptor Z7
software for creation of documentation from
electrical measurements SONEL PE5"
software for creation drawings and diagrams
"SONEL Schematic” + „SONEL PE5”
Ø=52
-
“
-
WAPRZ005REBB
WAPRZ010REBB
WAPRZ020REBB
WAPRZLAD230
WAPRZLAD12SAM
WAADAAC16
WAADAAGT16P
WAADAAGT32P
WAADAAGT63P
WAADAAISO10C
WAADATWR1J
WAADAWS04
WASONG80
WAFUTL3
WACEGC3OKR
WAAKU07
WAKROBU20K02
WAZACIMA1
WAPOZSZP1
WAZASZ7
WAPROSONPE5
WAPROSCHEM
Optional accesories of the meter MPI-520:
The MPI-520 multifunction meter is dedicated
to perform diagnosis of electrical installation
according to IEC 61557 standards. Digital
meter MPI-520 is designed to measure
impedance of a short cicuit loop also without
triggering RCD, parameters of RCD, insulation
resistance, earthing resistance, continuity and
also for phase sequence testing. Furthermore
it is used for measurement of AC voltage and
current, frequency and power.
Possible measurements
Testing of general and selective RCD with the rated
differential current of 10,30,100,300,500 and 1000mA.
(Type AC, A and B).
Measurement of insulation resistance:
- with test voltage 250V, 500V, 1000V,
Bi-directional testing of PE wire continuity using
200mA current.
- Autocalibration of test leads.
Phase sequence testing.
Memory is divided into 10 memory banks each of them containing
99 memory cells.
Battery charge indicator.
AUTO-OFF function.
USB interface.
·
·
·
·
·
·
·
·
·
·
·
Short-circuit loop measurement:
- impedance measurement with 23A current (44A phase-to-phase) -
short-circuit resistor R=10Ω,
- measurement range: 95...440V, frequency 45...65Hz,
Shor t - c ircu i t lo o p mea s u remen t w ith r e s oluti o n
0,01Ω, in distribution network without tiggering RCD
(I ≥30mA):
Δn
- automatic calculation of short-circuit, detection of phase voltage
and phase-to-phase voltage,
- additional UNI-Schuko plug for automatic measurement,
AGT adapter for 3 phase network measurement.
- measurement range up to 3GΩ,
- UNI-Schuko plug for insulation measurement,
- automatic discharging after measurement,
- automatic measurement of all resistences in 3,4,5-wire cables
using optional adapter AUTO-ISO,
- acoustic signals in 5sec intervals for insulation resistance
characteristic,
- safety measurement - protection against overvoltage.
Measurement of earthing resistance.