Instruction Manual

32
Program Monday Tuesday Wednesday Thursday Friday Saturday Sunday
P1 8:00-17:00 8:00-17:00 8:00-17:00 8:00-17:00 8:00-17:00 8:00-17:00 8:00-17:00
P2 18:00-7:00* 18:00-7:00* 18:00-7:00* 18:00-7:00* 18:00-7:00* 18:00-7:00* 18:00-7:00*
P3 8:00-17:00 8:00-17:00 8:00-17:00 8:00-17:00 8:00-17:00 OFF OFF
P4 18:00-7:00* 18:00-7:00* 18:00-7:00* 18:00-7:00* 18:00-7:00* OFF OFF
P5 OFF OFF OFF OFF OFF 00:00-23:59 00:00-23:59
P6 SET SET SET SET SET SET SET
*: the switch off time is at a different day
The P6 program can be set freely, you can set a switch on/off time for each day of the week. If you set 00 to power on/off time for a day of
the week, the appliance will not perform a scheduled program that day. When setting the program, you can only set whole hours during the
program setup, not minutes. Make sure, that on the given day the switch off time is set after the switch on time.
To set the program, select P6 program, then press the OK button. Then on the display 1 is flashing
– Monday. Press the OK button, on the display 00 is lighting, use the +/- selector buttons to set the switch on hour. Press the OK button,
on the display 00 is lighting, use the +/- selector buttons to set the switch off hour. Press the OK button on the display, 2 is flashing on the
display – Tuesday. After setting the switch off time on Sunday and pressing the OK button, the program is active.
Whenever you select the P6 program, you can always change the previously set program. By pressing the OK button several times,
repeatedly to scroll through the previously set values and either change or leave them.
When you power off the appliance, it forgets the exact time and program set for the P6.
If any program is selected, the unit operates in the most recently used mode – or in any of the heating stages, or according to the
temperature set in the thermostat mode.
If the weekly program is active, the indicator (13) is lighting on the appliance’s display. If the program is active but the device is not working,
the indicator (13) is flashing.
If any program is selected, if the program does not function when selected, in some cases the appliance switches to fan mode for 30
seconds and then stop.
You can switch off the weekly program operation at any time, by pressing the (22) button on the remote control to enter programming, then
pressing the remote control’s (25) button.
In case of overheating, the overheating protection function will switch off the unit, for example, when the air inlets and outlets are
covered. Power off the unit by unplugging it from the electric outlet. Allow the appliance to cool (for at least 30 minutes). Check whether the
air inlets and outlets are obstructed or not, and clean them if necessary. Switch on the unit again. If the overheating protection activates
again, power off the unit by unplugging it from the electric outlet and contact the service facility.
SPECIFICATIONS
power supply: ............................................... 230 V~ / 50 Hz
output: .......................................................... 1000 / 2000 W
maximal output: ............................................ 2000 W
IP protection: ................................................ IP20: Not protected from ingress of water!
dimensions of heater:................................... 56 x 19 x 12 cm
weight: .......................................................... 2,5 kg
sound pressure: ........................................... 60 dB(A)
* The PTC (Positive Temperature Coefficient – positive temperature coefficient) is a ceramic polycrystalline semiconductor, alloyed with
barium and titanium. The real advantage is that it has temperature self-regulating ability, so youdo not needany precautions against
overheating, and the device is considerably energy-saving.