Instruction Manual
32
EN -Functions / H - Funkciók / SK - Funkcie / RO - Funcţii / SRB-MNE - Funkcije / CZ - Funkce /
HR-BIH - Funkcije
SMART CONVECTOR HEATER
FEATURES
smart convector heater, for heating the air of indoor premises • can be controlled with touch buttons, by remote control or the free
smartphone application • adjustable output 1000 W / 1300 W / 2300 W• frost guard function • turbo fan function which can be switched
independently • electronic thermostat • 24-hour switch off timer • standalone design • overheating protection
OPERATION
The appliance can be controlled with its touch-buttons, by remote control or the free smartphone application.
Switch the main switch (1) on the side of the appliance on. Then the appliance beeps shortly, the measured temperature can be read
on the appliance’s display (14). You can switch the appliance on using the remote control, or the appliance’s ON/OFF switch button (3).
Then, the set temperature (15) can be read on the display next to the measured value.
The turbo fan function can be turned on or off at any time, regardless of the set value of the thermostat and the selected heating level,
with the exception of the frost protection function (7). The appliance indicates the operation of the fan function on its display (17).
To activate heating mode, after setting the thermostat, you need to select the desired heating stage (6). On the appliance’s display you
can see the selected heating stage (16), or the indicator of the frost guard function (18). If the ambient temperature decreases 2 °C
below the set value, then the appliance switches on. If the ambient temperature reaches the set value, the heating element switches off.
In case of selecting the frost guard function, the thermostat automatically sets into 5 °C, and if the measured temperature decreases
below it, the appliance switches on in 2300 W heating stage.
It is possible to set switch off timer hourly, for maximum 24 hours, by pressing repeatedly the appliance’s or the remote control’s
corresponding button (9). The set value, and the remaining time until switching off are readable on the display (19).
Smartphone application:
The mobile phone must be connected to the Internet.
1. Scan the QR code with your phone (Figure 4.), then download and install the „Tuya Smart” application.
2. Select the country code and enter your mobile phone number, then press the „Get” button.
3. Enter the („verification code”) you received in SMS, and enter the password you want to use for the application containing numbers
and letters.
4. Enter the application: „Login”
5. Make sure that your device and smartphone are as close as possible and connected to the WIFI router.
6. Press the „+” button to add the new appliance to the program.
7. Select the type of the appliance: „Small home appliances” → „Heaters”
8. Press and hold the heater’s or the remote control’s WIFI reset button (5), until „AP 00” appears on the appliance’s display.
9. Enter the password of the WIFI network you want to use on your appliance, then press the „Next” button.
10. Select in the application that the heater’s WIFI indicator blinks quickly. After this, pairing runs, the heater connects to the cloud-
based application.
Using the application, you can control all functions of the device.
You can disconnect the heater anytime from the cloud-based application. For this, press and hold the heater’s or the remote control’s
WIFI reset button until the red indicator light starts flashing quickly, the heater beeps once, then the indicator light goes out.
In the event of overheating, the overheating protection function switches off the unit. Power off the unit by unplugging it from the
electric outlet. Allow the appliance to cool down (min. 30 minutes). Check whether the air inlet and outlet openings are obstructed or not,
and clean them if necessary. Reinstall the appliance. If overheating protection activates again, power off the appliance by unplugging
its power plug and contact a service facility.
SPECIFICATIONS
power supply: ............................................ 230 V~ / 50 Hz
output......................................................... 1000 W / 1300 W / 2300 W
maximum output: ....................................... 2300 W
IP protection: ............................................. IP20: The appliance is not protected against ingress of water.
dimensions heater: .................................... 68 x 41,5 x 18 cm
transmission frequency .............................. 2,4 GHz / 1 mW
noise level: ................................................ 56 dB(A)
weight: ....................................................... 4,5 kg