Use and Care Manual

CLEAN ONLY WITH MILD SOAP AND WATER. AVOID SPRAYING WITH CLEANSERS, INSECTICIDES, AND PESTICIDES
THAT ARE PETROLEUM BASED HYDROCARBON PRODUCTS. THESE WILL DEGRADE LUMINAIRE.
INSTALLATION INSTRUCTIONS
R E A D I M P O R TA N T S A F E T Y T I P S B E F O R E P R O C E E D I N G W I T H I N S T A L L AT I O N
Turn fixture off! (Place wall switch in off
position, if fixture has built-in switch or
chain pull, switch or pull chain so fixture
is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
1
2
IFH146INC
3 4
POSITION THE FIXTURE HOUSING over the fixture
mounting screws and secure in place with the cap nuts
provided.
SCREW BULB into socket. Be sure to use bulb with wattage no
greater than specified on fixture. NOTE: Cage does not have to
be removed to install bulb.
NOTE: Fixture MUST be caulked with an acrylic caulk where
fixture housing meets mounting surface. This provides a water
tight seal when fixture is installed.
This fixture may have an integral photo sensor that turns the fixture off during the day and on at night. The photo sensor is not
adjustable. The fixture could possibly cycle on and off due to light reflected from nearby surfaces into the photo sensor. If cycling
occurs, remove the photo sensor nut and install the swivel hood base.
The hood and base and adjustable hood can be rotated and base can be cut along dotted line to reduce overall
lenth. Check operation before cutting the base.
HOOD
BASE
Screw 8-32 x 1 1/2” steel screws (provided) into mounting
plate. Head of screw to be flush with back of mounting plate.
Thread one 8-32 locking nut (provided) on to each screw
until it is flush and tight with front of mounting plate. Attach
mounting plate to outlet box, with screw threads facing
outward, using the outlet box screws. Connect the wires from
the outlet box and fixture. Attach black fixture wire to black
supply wire, white fixture wire to white supply wire, and bare
or green ground supply wire using wire connectors.
wire connectors
(not provided)
fixture wire
8-32 x 1 1/2”
steel screw
mounting plate
outlet box
screws
(not provided)
caulk
cage
To remove cage from roof, loosen the two roof
securing screws.
roof securing
screws
( 2 places)
fixture
mounting
screws
photocell
(optional)
cap nuts
locking
nut
CLEAN ONLY WITH MILD SOAP AND WATER. AVOID SPRAYING WITH CLEANSERS, INSECTICIDES, AND PESTICIDES
THAT ARE PETROLEUM BASED HYDROCARBON PRODUCTS. THESE WILL DEGRADE LUMINAIRE.
INSTALLATION INSTRUCTIONS
R E A D I M P O R T A N T S A F E T Y T I P S B E F O R E P R O C E E D I N G W I T H I N S TA L L A T I O N
Turn fixture off! (Place wall switch in off
position, if fixture has built-in switch or
chain pull, switch or pull chain so fixture
is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
1
2
IFH146INC
3 4
POSITION THE FIXTURE HOUSING over the fixture
mounting screws and secure in place with the cap nuts
provided.
SCREW BULB into socket. Be sure to use bulb with wattage no
greater than specified on fixture. NOTE: Cage does not have to
be removed to install bulb.
NOTE: Fixture MUST be caulked with an acrylic caulk where
fixture housing meets mounting surface. This provides a water
tight seal when fixture is installed.
This fixture may have an integral photo sensor that turns the fixture off during the day and on at night. The photo sensor is not
adjustable. The fixture could possibly cycle on and off due to light reflected from nearby surfaces into the photo sensor. If cycling
occurs, remove the photo sensor nut and install the swivel hood base.
The hood and base and adjustable hood can be rotated and base can be cut along dotted line to reduce overall
lenth. Check operation before cutting the base.
HOOD
BASE
Screw 8-32 x 1 1/2” steel screws (provided) into mounting
plate. Head of screw to be flush with back of mounting plate.
Thread one 8-32 locking nut (provided) on to each screw
until it is flush and tight with front of mounting plate. Attach
mounting plate to outlet box, with screw threads facing
outward, using the outlet box screws. Connect the wires from
the outlet box and fixture. Attach black fixture wire to black
supply wire, white fixture wire to white supply wire, and bare
or green ground supply wire using wire connectors.
wire connectors
(not provided)
fixture wire
8-32 x 1 1/2”
steel screw
mounting plate
outlet box
screws
(not provided)
caulk
cage
To remove cage from roof, loosen the two roof
securing screws.
roof securing
screws
( 2 places)
fixture
mounting
screws
photocell
(optional)
cap nuts
locking
nut