Use and Care Manual

CLEAN ONLY WITH MILD SOAP AND WATER. AVOID SPRAYING WITH CLEANSERS, INSECTICIDES, AND PESTICIDES
THAT ARE PETROLEUM BASED HYDROCARBON PRODUCTS. THESE WILL DEGRADE LUMINAIRE.
INSTALLATION INSTRUCTIONS
R E A D IMP O R TA N T SAFETY TIPS B EFORE PROCEED I NG WITH I NSTA LLATION
Turn fixture off! (Place wall switch in off
position, if fixture has built-in switch or
chain pull, switch or pull chain so fixture
is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
1
2
IS50VFINC
3 4
SCREW BULB into socket. Be sure to use bulb with wattage no
greater than specified on fixture. NOTE: Cage does not have to
be removed to install bulb.
NOTE: Fixture MUST be caulked with an acrylic caulk where
fixture housing meets mounting surface. This provides a water
tight seal when fixture is installed.
caulk
cage
This fixture may have an integral photo sensor that turns the fixture off during the day and on at night. The photo sensor is not
adjustable. The fixture could possibly cycle on and off due to light reflected from nearby surfaces into the photo sensor. If cycling
occurs, remove the photo sensor nut and install the swivel hood base.
The hood and base and adjustable hood can be rotated and base can be cut along dotted line to reduce overall
lenth. Check operation before cutting the base.
HOOD
BASE
To remove cage from roof grasp cage and rotate counter
clockwise until - shaped tabs on roof align with -
shaped opening on cage. Cage can then be removed.
NOTE: FIXTURES IS PROVDED WITH A TAMPER PROOF
SCREW TO PREVENT REMOVAL OF CAGE.
tamper proof
screw location
twist to
open
CLEAN ONLY WITH MILD SOAP AND WATER. AVOID SPRAYING WITH CLEANSERS, INSECTICIDES, AND PESTICIDES
THAT ARE PETROLEUM BASED HYDROCARBON PRODUCTS. THESE WILL DEGRADE LUMINAIRE.
INSTALLATION INSTRUCTIONS
R EAD IMP O R TA NT S AFETY TIPS BEFOR E P R O CEED ING WITH INS TALLATION
Turn fixture off! (Place wall switch in off
position, if fixture has built-in switch or
chain pull, switch or pull chain so fixture
is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
1
2
IS50VFINC
3 4
SCREW BULB into socket. Be sure to use bulb with wattage no
greater than specified on fixture. NOTE: Cage does not have to
be removed to install bulb.
NOTE: Fixture MUST be caulked with an acrylic caulk where
fixture housing meets mounting surface. This provides a water
tight seal when fixture is installed.
caulk
cage
This fixture may have an integral photo sensor that turns the fixture off during the day and on at night. The photo sensor is not
adjustable. The fixture could possibly cycle on and off due to light reflected from nearby surfaces into the photo sensor. If cycling
occurs, remove the photo sensor nut and install the swivel hood base.
The hood and base and adjustable hood can be rotated and base can be cut along dotted line to reduce overall
lenth. Check operation before cutting the base.
HOOD
BASE
To remove cage from roof grasp cage and rotate counter
clockwise until - shaped tabs on roof align with -
shaped opening on cage. Cage can then be removed.
NOTE: FIXTURES IS PROVDED WITH A TAMPER PROOF
SCREW TO PREVENT REMOVAL OF CAGE.
tamper proof
screw location
twist to
open
Screw 8-32 x 1 1/4” steel screws (provided) into swivel
mounting plate. Head of screw to be flush with back of swivel
mounting plate. Thread one 8-32 locking nut (provided) on
to each screw until it is flush and tight with front of swivel
mounting plate. Attach swivel mounting plate to outlet box,
with screw threads facing outward, using the outlet box
screws. Connect the wires
from the outlet box and fixture.
Attach black fixture wire to black supply wire, white fixture
wire to white supply wire, and bare or green ground supply
wire using wire connectors.
wire connectors
(not provided)
fixture wire
8-32 x 1 1/4”
steel screw
swivel
mounting plate
locking nut
POSITION THE FIXTURE HOUSING over the
the cap nuts provided.
photocell
(optional)
Screw 8-32 x 1 1/4” steel screws (provided) into swivel
mounting plate. Head of screw to be flush with back of swivel
mounting plate. Thread one 8-32 locking nut (provided) on
to each screw until it is flush and tight with front of swivel
mounting plate. Attach swivel mounting plate to outlet box,
with screw threads facing outward, using the outlet box
screws. Connect the wires
from the outlet box and fixture.
Attach black fixture wire to black supply wire, white fixture
wire to white supply wire, and bare or green ground supply
wire using wire connectors.
wire connectors
(not provided)
fixture wire
8-32 x 1 1/4”
steel screw
swivel
mounting plate
locking nut
POSITION THE FIXTURE HOUSING over the
the cap nuts provided.
photocell
(optional)