Instructions / Assembly

rew
ol
IFR121I60
IFR121I60
(A) 8-32 x 1 1/2” Steel Screw
(B) Mounting
Plate
Caulk Edge
(E) Fixture Canopy
Assembly
(F) 8-32 Cap Nut
Insert 8-32 x 1 1/2" steel screws (A) [provided] into
mounting plate (B). Attach mounting plate to
the outlet box, with screw threads
facing outward, using the outlet box screws (C)
[provided]. Connect the wires from the outlet
box and fixture. Attach black fixture wire to
black supply wire, white fixture wire to white
supply wire and bare or green ground fixture
wire to green ground supply wire using wire
connectors (D).
SAFETY TIPS
READ IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH INSTALLATION
INSTALLATION INSTRUCTIONS
Turn fixt ure off! (Place w all switc h
in off positio n, if fixture has built-i n
switch or chain pull, switch or pull
chain so fixture is off. )
Screw-in type fuses - unsc
the fuse or fuses that cont r
the po wer to the fixture or
room you are working in.
Next - go to t he main fuse box.
If your fuse box has an ON/OFF
switch , simply place main power
switch in OFF position.
1
2
Align mounting holes in the Fixture Canopy
Assembly (E) with the 8-32 x 1 1/2 " steel screws
(A) in the mounting plate, position fixture over
outlet box and hold the fixture against the
mounting wall. Secure fixture to the wall by
tightening the two cap nuts (F) onto the 8-32
screws. Tighten by using pliers to properly
secure the fixture. Once tightened against the
wall, the edge between the Fixture Canopy
Assembly and wall should be caulked with an
acrylic caulk (not supplied) to provide a water
tight seal.
Screw bulb into socket. Be sure to use bulb type
and wattage specified on fixture.
(A) 8-32 x 1 1/2”
Steel Screw
(C) Outlet Box Screw
(D) Wire Connectors
Fixture Wire
(B) Mounting Plate
CLEAN ONLY WITH MILD SOAP AND WATER. AVOID SPRAYING WITH
CLEANSERS, INSECTICIDES, AND PESTICIDES THAT ARE PETROLEUM
BASED HYDROCARBON PRODUCTS. THESE WILL DEGRADE LUMINAIRE.
This fixture may have an integral photo sensor that turns the fixture off during the day and on
at night. The photo sensor is not adjustable. The fixture could possibly cycle on and off due to
light reflected from nearby surfaces into the photo sensor. If cycling occurs, remove the photo
sensor nut and install the swivel hood and base.
The hood and base are adjustable. The hood can be rotated and the base can be cut along the dotted line to
reduce overall length. Check operation before cutting the base.
HOOD
BASE
(A) 8-32 x 1 1/2” Steel Screw
(B) Mounting
Plate
Caulk Edge
(E) Fixture Canopy
Assembly
(F) 8-32 Cap Nut
Insert 8-32 x 1 1/2" steel screws (A) [provided] into
mounting plate (B). Attach mounting plate to
the outlet box, with screw threads
facing outward, using the outlet box screws (C)
[provided]. Connect the wires from the outlet
box and fixture. Attach black fixture wire to
black supply wire, white fixture wire to white
supply wire and bare or green ground fixture
wire to green ground supply wire using wire
connectors (D).
SAFETY TIPS
READ IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH INSTALLATION
INSTALLATION INSTRUCTIONS
Turn fixt ure off! (Place w all switc h
in off positio n, if fixture has built-i n
switch or chain pull, switch or pull
chain so fixture is off. )
Screw-in type fuses - unscrew
the fuse or fuses that cont rol
the po wer to the fixture or
room you are working in.
Next - go to t he main fuse box.
If your fuse box has an ON/OFF
switch , simply place main power
switch in OFF position.
1
2
Align mounting holes in the Fixture Canopy
Assembly (E) with the 8-32 x 1 1/2 " steel screws
(A) in the mounting plate, position fixture over
outlet box and hold the fixture against the
mounting wall. Secure fixture to the wall by
tightening the two cap nuts (F) onto the 8-32
screws. Tighten by using pliers to properly
secure the fixture. Once tightened against the
wall, the edge between the Fixture Canopy
Assembly and wall should be caulked with an
acrylic caulk (not supplied) to provide a water
tight seal.
Screw bulb into socket. Be sure to use bulb type
and wattage specified on fixture.
(A) 8-32 x 1 1/2”
Steel Screw
(C) Outlet Box Screw
(D) Wire Connectors
Fixture Wire
(B) Mounting Plate
CLEAN ONLY WITH MILD SOAP AND WATER. AVOID SPRAYING WITH
CLEANSERS, INSECTICIDES, AND PESTICIDES THAT ARE PETROLEUM
BASED HYDROCARBON PRODUCTS. THESE WILL DEGRADE LUMINAIRE.
This fixture may have an integral photo sensor that turns the fixture off during the day and on
at night. The photo sensor is not adjustable. The fixture could possibly cycle on and off due to
light reflected from nearby surfaces into the photo sensor. If cycling occurs, remove the photo
sensor nut and install the swivel hood and base.
The hood and base are adjustable. The hood can be rotated and the base can be cut along the dotted line to
reduce overall length. Check operation before cutting the base.
HOOD
BASE