Instructions / Assembly

CONNECT THE WIRES. NOTE: Attach
black fixture wire to black supply
wire, white fixture wire to white
supply wire. Do not mix them up.
Use wire connectors (not provided).
Connect bare fixture ground wire to
ground wire from outlet box. NEVER
CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
ATTACH cross bar to outlet box with
outlet box screws (8-32 x 1/2, 2 slotted
screws provided).
Place diffuser on fixture base. Then place bar grill or frame
(depending on fixture model) over diffuser and attach to base
with mounting screws (8-32x1/2, 4 combination head screw
provided). NOTE: On models with hood, attach diffuser to
base with one combination head mounting screw at center
top of base only. Place hood over diffuser and secure to base
with remaining three mounting screws. NOTE: Outdoor wall
fixture MUST be caulked with an acrylic caulk where base of
fixture meets mounting surface. This provides a water tight
seal when fixture is installed.
INSTALLATION INSTRUCTIONS
READ IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH INSTALLATION
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
bar grill
cross bar
outlet box
basediffuser
IS009 Rev D
Clean only with mild soap and water. Avoid spraying with cleansers, insecticides, and pesticides that are petroleum
based hydrocarbon products. These will degrade Luminaire.
POSITION THE FIXTURE over the
outlet box and secure in place with
the mounting screw (1/4-20 x 1,1
provided). Screw lamp into lampholder.
Use lamp type and wattage specified on
fixture
outlet box screws
ground wire
washer
wall
mounting
screw
mounting screws
ON MODELS WITH HOOD, attach to wall with reflector up.
Hood is to be placed above reflector as shown.
4
1 2 3
5
ground wire
wire connectors
(not provided)
cross bar
diffuser
reflector
hood
CONNECT THE WIRES. NOTE: Attach
black fixture wire to black supply
wire, white fixture wire to white
supply wire. Do not mix them up.
Use wire connectors (not provided).
Connect bare fixture ground wire to
ground wire from outlet box. NEVER
CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
ATTACH cross bar to outlet box with
outlet box screws (8-32 x 1/2, 2 slotted
screws provided).
Place diffuser on fixture base. Then place bar grill or frame
(depending on fixture model) over diffuser and attach to base
with mounting screws (8-32x1/2, 4 combination head screw
provided). NOTE: On models with hood, attach diffuser to
base with one combination head mounting screw at center
top of base only. Place hood over diffuser and secure to base
with remaining three mounting screws. NOTE: Outdoor wall
fixture MUST be caulked with an acrylic caulk where base of
fixture meets mounting surface. This provides a water tight
seal when fixture is installed.
INSTALLATION INSTRUCTIONS
READ IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH INSTALLATION
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
bar grill
cross bar
outlet box
basediffuser
IS009 Rev D
Clean only with mild soap and water. Avoid spraying with cleansers, insecticides, and pesticides that are petroleum
based hydrocarbon products. These will degrade Luminaire.
POSITION THE FIXTURE over the
outlet box and secure in place with
the mounting screw (1/4-20 x 1,1
provided). Screw lamp into lampholder.
Use lamp type and wattage specified on
fixture
outlet box screws
ground wire
washer
wall
mounting
screw
mounting screws
ON MODELS WITH HOOD, attach to wall with reflector up.
Hood is to be placed above reflector as shown.
4
1 2 3
5
ground wire
wire connectors
(not provided)
cross bar
diffuser
reflector
hood