Instructions / Assembly

INSTALLATION INSTRUCTIONS
READ IMPORTAN T S A F E T Y T I P S B E F O R E P R O C E E D I N G W I T H I N S TAL L ATI O N
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
IFD154
THREAD fixture mounting screws (provided) into outer cross
bar. ATTACH cross bar to outlet box with outlet box screws
(not provided).
CONNECT THE WIRES. NOTE: Attach black fixture wire to
black supply wire, white fixture wire to white supply wire.
Do not mix them up. Use wire connectors (not provided).
Connect green fixture ground wire to ground wire from outlet
box. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
2
1
outlet box
screws
(not provided)
cross bar
fixture mounting
screws
outlet box
(not provided)
outer cross bar
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE BRANCH CIRCUIT CONDUCTOR
outlet box
wire connectors
(not provided)
ground wire
fixture
housing
cross bar
3 4
POSITION THE FIXTURE HOUSING over the fixture
mounting screws and secure in place with the thumb
nuts provided.
fixture
mounting
screws
outer
cross bar
thumb nuts
NOTE: Fixture MUST be caulked with an acrylic caulk where
fixture housing meets mounting surface. This provides a
water tight seal when fixture is installed.
fixture housing
photocell
(optional photo sensor)
caulk
NOTE: If photo sensor is provided fixture will turn on at dusk
and off at dawn.
Clean only with mild soap and water. Avoid spraying with Cleansers, Insecticides,
and Pesticides that a petroleum based hydrocarbon products. These will degrade
Luminaire.
CAUTION: Do not turn on without diffuser installed. Do not touch LEDs or circuit board. No
lamp replacement required! Integral LED light engine supplied.
INSTALLATION INSTRUCTIONS
READ I M P O RTA N T S A F E T Y T I P S B E F O R E P R O C E E D I N G W I T H I N S TA L L ATI O N
Turn fixture off! (Place wall switch
in off position, if fixture has built-in
switch or chain pull, switch or pull
chain so fixture is off.)
Next - go to the main fuse box. If
your fuse box has an ON/OFF switch,
simply place main power switch in
OFF position.
SAFETY TIPS
Screw-in type fuses - unscrew the fuse
or fuses that control the power to the
fixture or room you are working in.
IFD154
THREAD fixture mounting screws (provided) into outer cross
bar. ATTACH cross bar to outlet box with outlet box screws
(not provided).
CONNECT THE WIRES. NOTE: Attach black fixture wire to
black supply wire, white fixture wire to white supply wire.
Do not mix them up. Use wire connectors (not provided).
Connect green fixture ground wire to ground wire from outlet
box. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
2
1
outlet box
screws
(not provided)
cross bar
fixture mounting
screws
outlet box
(not provided)
outer cross bar
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE BRANCH CIRCUIT CONDUCTOR
outlet box
wire connectors
(not provided)
ground wire
fixture
housing
cross bar
3 4
POSITION THE FIXTURE HOUSING over the fixture
mounting screws and secure in place with the thumb
nuts provided.
fixture
mounting
screws
outer
cross bar
thumb nuts
NOTE: Fixture MUST be caulked with an acrylic caulk where
fixture housing meets mounting surface. This provides a
water tight seal when fixture is installed.
fixture housing
photocell
(optional photo sensor)
caulk
NOTE: If photo sensor is provided fixture will turn on at dusk
and off at dawn.
Clean only with mild soap and water. Avoid spraying with Cleansers, Insecticides,
and Pesticides that a petroleum based hydrocarbon products. These will degrade
Luminaire.
CAUTION: Do not turn on without diffuser installed. Do not touch LEDs or circuit board. No
lamp replacement required! Integral LED light engine supplied.