User Manual

13
8. Cleaning Procedures
8.1 Door Lint Filter
As with all clothes dryers, your lint filter should be cleaned
after each use.
Note:
— Lint accumulates on the lint filter and will block the air
circulation. This effects the performance of your clothes
dryer and will extend the required drying time.
— Always disconnect the power cord before cleaning!
— Do not operate the dryer without the lint filter installed!
— Clean the lint filter after each use .
To clean the lint filter:
— Ensure the dryer has cooled down after any recent
operation.
— Unplug the appliance.
— Open the appliance door.
— Take out the lint filter and wipe off any accumulated lint
and fibres with your hand, or rinse the filter with water
and dry thoroughly.
— Re-install the lint filter.
8.2 Cleaning the Heat Exchanger
WARNING! Do not touch the heat exchanger with your
hand as it may cause injury.
As necessary, approx. once every 6 months, remove the
u from the heat exchanger using a vacuum cleaner with a
dusting brush attached. Clean the heat exchanger without
applying any pressure. Otherwise the heat exchanger could
be damaged. The dryer will not dry if the cooling ns are
damaged or bent.
8.3 Empty the water container
WARNING! After each use, the water container should
be emptied.
— Hold and pull out the water container using two hands.
— Tilt the water container, pouring out the condensed
water in to a sink.
— Re-insert the water container into the appliance.
Note:
If the container requires emptying during operation, the
program will pause and the “Full & ” icon will flash on
the display. Follow the process above to empty the
container and restart the program by pressing the
“Start/Pause” button.
WARNING!
— Do not drink the condenser water.
— Do not operate the dryer without the water container
in place.
8.4 Error Displays
Cleaning & Maintenance
MAINTENANCE
24
Trouble Shooting
• Only authorised technicians can carry out repairs.
• If the LED displays other prompt and the dryer does not work, please call
the service.
Warning!
！！
Many malfunctions and faults that might occur in daily operation can be easily
remedied. Time and money will be saved because a service call won't be needed.
The following guide may help you to find the reason for a malfunction and correct it.
Note!
Before you call the service, please check if you have dealt with the problems yourself
consulting the user instructions.
“ ” E32
“ ”E33
Display
Reason
Solutions
Humidity sensor error
Temperature sensor error
Please contact your local
problem occurs.
service center if the
“ ”E82
PCB communication error
Water pump failure or water
level sensor failure
Container is full
Empty container
“Full& “
MAINTENANCE
21
Empty the water container
Clean the filter door
1. Pull out and hold the water container
with two hands.
2. Tilt the water container, pour out the
condensate water into the basin.
3. Install the water container.
Clean the filters
Cleaning and Care
This dryer has a primary door lint filter and a base filter in front of the heat exchanger
for additional protection. Make sure you clean the door filter after each cycle.
The base filter need to be cleaned after each fifth drying programme.
1. Open the door.
2. Take out the filter.
3. Open the filter and remove the fluff on
the filter, You can clean it in water.
4. Dry the filter thoroughly before
installing it back.
door
running
door
• Take notice of the correct orientation
before to insert the door filter.
Note!
Door Filter
• Empty the water container after each use. Once the water container is filled
completely, the programme will be paused and the "Full& " icon will light.
After the container is emptied, the dryer can be restarted by pressing
【Start/Pause】button.
• Do not drink the condensate water.
• Do not use the dryer without the water container.
Warning!
！！
MAINTENANCE
22
regularly will increase drying time and energy consumption.
• Disconnect the power cord before cleaning!
• Do not operate the dryer without the filter!
• The fluff accumulated on the filter will block the air circulation. Not cleaning the filter
Note!
As necessary, approx. once every 6 months, remove the fluff from the heat
exchanger using a vacuum cleaner with a dusting brush attached.
Clean the heat exchanger without applying any pressure. Otherwise the heat
exchanger could be damaged. The dryer will not dry
if the cooling fins are damaged or bent.
•
•
Clean the heat exchanger
Warning!
！！
Do not touch the heat exchanger with your hand,
which may cause an injury.