Instructions

ManualsBrandsSolinst ManualsPower WinderSolinst 101 Power Winder

Power Winder Instructions

High Quality Groundwater and Surface Water Monitoring Instrumentation

(Page 1 of 3)

Model 101 – For use with all SC1000, SC2000 & SC3000 Reels

Installation Instructions

1. Use a large ﬂathead screwdriver or 8 mm (5/16”) wrench/

socket to loosen the two gear clamps. (When you ﬁrst receive

the Power Winder, the gear clamps will be loosened.)

Thumb Screws

Rollers

3/32"Allen Key

Gear

Clamps

Telescoping

Arms

Swing Arm

Note: If installing on an SC2000 (medium) or SC3000 (large) Solinst

reel, step 2 may not be required, as there is enough space

between the frame and hub to easily ﬁt the Power Winder.

2. Be mindful of the potential pinch-points of the swing arm

motion. Use the ‘heel’ of your hand to push ﬁrmly down on

the roller drive Shaft until it reaches the base plate. Push

the Locking Pin into the hole on the Swing Arm. This will

hold the spring-loaded swing arm in place. Ensure the pin

is pushed in all the way. This will hold the rollers out of the

way while installing on an SC1000 (small) reel.

3. Place the reel on its side with the faceplate up.

4. Slide the Power Winder base onto the left leg of the reel

frame, with the rollers towards the hub. Ensure the base of

the Power Winder is pushed all the way back on the left leg

of the reel until it stops.

5. With the reel still on its side, tighten the gear clamps to secure

the Power Winder to the reel. This ensures the Power Winder is

tight against end of leg and the rollers are aligned with the reel.

6. If not already, loosen the black thumb screws on the

telescoping arms of the Power Winder, and adjust them to

the appropriate length so they ﬁt over the legs of the reel

frame. Tighten the thumbscrews to hold the arms in place.

Locking Pin

...continued on page 2

1/4" Hex Drill

Fitting

Roller Drive

Shaft

Solinst Model 101 Power Winder (#116159)

Base Plate

More Info | Instructions | Get Quote

Summary of content (3 pages)

PAGE 1
Power Winder Instructions More Info | Instructions | Get Quote Model 101 – For use with all SC1000, SC2000 & SC3000 Reels Swing Arm Roller Drive Shaft 3/32"Allen Key Base Plate Telescoping Arms Locking Pin Thumb Screws Gear Clamps 1/4" Hex Drill Fitting Rollers Solinst Model 101 Power Winder (#116159) Installation Instructions 1. Use a large flathead screwdriver or 8 mm (5/16”) wrench/ socket to loosen the two gear clamps. (When you first receive the Power Winder, the gear clamps will be loosened.
PAGE 2
7. Push down on the roller drive shaft to release the locking pin. The swing arm will pop up and the rollers will engage against the edges of the reel’s faceplate and backplate. 2. Ensure to adjust the drill to an appropriate speed. Note: Setting your drill to a slower speed can allow more precise measurements of product layers or temperature or conductivity interfaces when using instruments such as the Solinst Model 122 Interface Meter or Model 107 TLC Meter.
PAGE 3
Using the Optional Flex Drill Adaptor (#116199) Using the Optional Cinch Straps (#116059) For easier access to the 1/4” hex fitting on the Power Winder, a Flex Drill Adaptor is available so you can operate the Power Winder using your drill/driver at any angle. A set of cinch straps is available for adding to the base of the Power Winder, to allow you to secure the Power Winder to a well casing or for use in another application. 1.