User Manual
Table Of Contents
- 1. Introduction of Ranger Watch W-10
- Specification
- Keys
- Getting Started
- 2. System Setting
- 2.1 Language
- 2.2 Tones and vibration
- 2.3 Display
- 2.4 Theme
- Time setting
- Alarm setting
- 2.7 Unit
- 2.8 Auto Suspend
- 2.9 Data Recording
- 2.10 Initial Setup：
- 2.11 Compass Calibration
- 2.12 User profile
- 3. Sport Setting
- 3.1 Change Sport Mode
- 3.2 Run setting
- 3.2.1 Data Fields
- Run Alerts
- 3.2.2.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.2.2.2 Alert with upper limit and lower limit – Cadence Alert, Speed Alert, HR Alert
- 3.2.2.3 Run/Walk Alert
- 3.2.3 Auto Lap
- 3.2.4 Auto Pause
- 3.2.5 Auto Scroll
- 3.2.6 Heart Rate Monitor
- 3.2.7 ANT+ Foot Pod
- Calibrate Step Distance
- 3.2.9 Workouts
- 3.2.9.1 Interval Workouts
- 3.2.9.2 Custom Workout
- 3.3 Bike Setting
- 3.3.1 Bike Details
- 3.3.2 Speed / Cadence
- 3.3.3 Data Fields
- Bike Alert
- 3.3.4.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.3.4.2 Alert with upper limit and lower limit – Cadence Alert, Pace Alert, HR Alert
- Auto Lap
- Auto Pause
- Auto Scroll
- Heart Rate Monitor
- Other Bikes
- Workouts
- Pace/Speed
- Countdown Timer
- Start Bike sport / training
- 3.4 Other (Sport) Settings
- 3.5 Outdoor Swim
- 3.6 Indoor Swim
- 3.7 Multi Sport
- 4. Datalog
- 4.1 Read Datalog
- 4.2 Check summary for each sport mode
- 4.3 Check Memory Details
- 4.4 SHOU-orbit website
- GPS function
- 5.1 GPS ON/OFF
- 5.2 To mark position
- 5.3 Guiding by GPS to the stored location.
- 5.4 Edit or delete the stored location
- 5.5 Back to Start
- 5.6 Stop Nanigation
- 5.7 Check GPS Satellites status
- 6. Bluetooth
- 7. Notification
- 7.1 Features
- 7.2 Operation procedure
- 8. Tempo Meter
- 9. Update Firmware (Operation System)
- 9.1 Download the new version of Firmware
- 9.2 Update Firmware (Operation System)
- 10. Important FCC notice:
5. GPS function
5.1 GPS ON/OFF
There are 2 ways to change Bluetooth ON/OFF.
The 1
st
way:
Short press the power key to pop out the quick setting screen Press up key ▲ or
down key ▼ to select GPS item, and press [ENTER] key to adjust GPS ON/OFF.
The 2
nd
way:
1. Press〔MODE〕key to menu page, select “GPS”, then select ｢GPS Status｣
2. In the GPS enable page, select ｢ON/Off｣, and then the GPS function is turned on
or off.
5.2 To mark position
If you are at the location that you want to mark, and want to visit again, you can mark
the location. Then you can find and go to the locations in future.
1. Turn on GPS, and go to the location that you want to mark.
2. As you are at the location and GPS is fixed, press〔MODE〕key to menu page, select
“GPS”, then select “Location Manager”