User Manual
Table Of Contents
- 1. Introduction of Ranger Watch W-10
- Specification
- Keys
- Getting Started
- 2. System Setting
- 2.1 Language
- 2.2 Tones and vibration
- 2.3 Display
- 2.4 Theme
- Time setting
- Alarm setting
- 2.7 Unit
- 2.8 Auto Suspend
- 2.9 Data Recording
- 2.10 Initial Setup：
- 2.11 Compass Calibration
- 2.12 User profile
- 3. Sport Setting
- 3.1 Change Sport Mode
- 3.2 Run setting
- 3.2.1 Data Fields
- Run Alerts
- 3.2.2.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.2.2.2 Alert with upper limit and lower limit – Cadence Alert, Speed Alert, HR Alert
- 3.2.2.3 Run/Walk Alert
- 3.2.3 Auto Lap
- 3.2.4 Auto Pause
- 3.2.5 Auto Scroll
- 3.2.6 Heart Rate Monitor
- 3.2.7 ANT+ Foot Pod
- Calibrate Step Distance
- 3.2.9 Workouts
- 3.2.9.1 Interval Workouts
- 3.2.9.2 Custom Workout
- 3.3 Bike Setting
- 3.3.1 Bike Details
- 3.3.2 Speed / Cadence
- 3.3.3 Data Fields
- Bike Alert
- 3.3.4.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.3.4.2 Alert with upper limit and lower limit – Cadence Alert, Pace Alert, HR Alert
- Auto Lap
- Auto Pause
- Auto Scroll
- Heart Rate Monitor
- Other Bikes
- Workouts
- Pace/Speed
- Countdown Timer
- Start Bike sport / training
- 3.4 Other (Sport) Settings
- 3.5 Outdoor Swim
- 3.6 Indoor Swim
- 3.7 Multi Sport
- 4. Datalog
- 4.1 Read Datalog
- 4.2 Check summary for each sport mode
- 4.3 Check Memory Details
- 4.4 SHOU-orbit website
- GPS function
- 5.1 GPS ON/OFF
- 5.2 To mark position
- 5.3 Guiding by GPS to the stored location.
- 5.4 Edit or delete the stored location
- 5.5 Back to Start
- 5.6 Stop Nanigation
- 5.7 Check GPS Satellites status
- 6. Bluetooth
- 7. Notification
- 7.1 Features
- 7.2 Operation procedure
- 8. Tempo Meter
- 9. Update Firmware (Operation System)
- 9.1 Download the new version of Firmware
- 9.2 Update Firmware (Operation System)
- 10. Important FCC notice:
Time Alert and Distance Alert
1. Press 〔MODE〕 key to menu page Select ｢Settings｣ Select ｢Outdoor Settings
｣ Select ｢Swim Alerts｣
2. Select ｢Time Alert｣ or ｢Distance Alert｣
3. Turn ON: Press〔ENTER〕 key to enter the setting page, and press ▲、▼ key to move
to ｢On/Off｣, select On to enable the alert, and press〔ENTER〕 key to confirm.
4. Adjust value to alert: Press ▲、▼ keys to the setting field—Alert At Press〔ENTER〕
key to start value adjusting of Time Alert or Distance Alert Press 〔ENTER〕 key
to confirm Press 〔MODE〕 key to leave the setting page.
As the user start the sport with pressing [START] key, and reach the alert point, Ranger
Watch will notify the user with message on display, and Message tone and vibration,
depending on the setting of Tone/Vibration in System setting.
3.5.3 Auto LAP
There are three modes for Auto Lap: by distance, time, or position.
★Note：Auto Lap is not available in Interval, customized workout and Indoor swim
mode.