User Manual
Table Of Contents
- 1. Introduction of Ranger Watch W-10
- Specification
- Keys
- Getting Started
- 2. System Setting
- 2.1 Language
- 2.2 Tones and vibration
- 2.3 Display
- 2.4 Theme
- Time setting
- Alarm setting
- 2.7 Unit
- 2.8 Auto Suspend
- 2.9 Data Recording
- 2.10 Initial Setup：
- 2.11 Compass Calibration
- 2.12 User profile
- 3. Sport Setting
- 3.1 Change Sport Mode
- 3.2 Run setting
- 3.2.1 Data Fields
- Run Alerts
- 3.2.2.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.2.2.2 Alert with upper limit and lower limit – Cadence Alert, Speed Alert, HR Alert
- 3.2.2.3 Run/Walk Alert
- 3.2.3 Auto Lap
- 3.2.4 Auto Pause
- 3.2.5 Auto Scroll
- 3.2.6 Heart Rate Monitor
- 3.2.7 ANT+ Foot Pod
- Calibrate Step Distance
- 3.2.9 Workouts
- 3.2.9.1 Interval Workouts
- 3.2.9.2 Custom Workout
- 3.3 Bike Setting
- 3.3.1 Bike Details
- 3.3.2 Speed / Cadence
- 3.3.3 Data Fields
- Bike Alert
- 3.3.4.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.3.4.2 Alert with upper limit and lower limit – Cadence Alert, Pace Alert, HR Alert
- Auto Lap
- Auto Pause
- Auto Scroll
- Heart Rate Monitor
- Other Bikes
- Workouts
- Pace/Speed
- Countdown Timer
- Start Bike sport / training
- 3.4 Other (Sport) Settings
- 3.5 Outdoor Swim
- 3.6 Indoor Swim
- 3.7 Multi Sport
- 4. Datalog
- 4.1 Read Datalog
- 4.2 Check summary for each sport mode
- 4.3 Check Memory Details
- 4.4 SHOU-orbit website
- GPS function
- 5.1 GPS ON/OFF
- 5.2 To mark position
- 5.3 Guiding by GPS to the stored location.
- 5.4 Edit or delete the stored location
- 5.5 Back to Start
- 5.6 Stop Nanigation
- 5.7 Check GPS Satellites status
- 6. Bluetooth
- 7. Notification
- 7.1 Features
- 7.2 Operation procedure
- 8. Tempo Meter
- 9. Update Firmware (Operation System)
- 9.1 Download the new version of Firmware
- 9.2 Update Firmware (Operation System)
- 10. Important FCC notice:
3.2.8 Calibrate Step Distance
★Note： You can get the step distance by adjusting the step distance by up key ▲ or
down key ▼，or calibrating the step distance by the calibration function.
Press〔MODE〕key to menu pageSelect ｢Settings｣Enter ｢Running settings｣
Select ｢Step Distance｣｢Calibrate｣。
There are two ways to calibrate step distance as following.
1. Calibrate by Distance：
In order to get the best result of step distance calibration, we recommend the user had
better do the calibration with 400 meters standard run way.
1. On ｢Calibration｣ page，press ｢Calibrate｣.Then calibrate by page, please select｢
Distance｣。
2. The default value is ｢400m｣(The length of standard run way is 400 meters）. The user
can adjust it with need.
3. Move to ｢Start｣ icon, and press [Enter] key, and the user can run or walk through
the distance.