User Manual
Table Of Contents
- 1. Introduction of Ranger Watch W-10
- Specification
- Keys
- Getting Started
- 2. System Setting
- 2.1 Language
- 2.2 Tones and vibration
- 2.3 Display
- 2.4 Theme
- Time setting
- Alarm setting
- 2.7 Unit
- 2.8 Auto Suspend
- 2.9 Data Recording
- 2.10 Initial Setup：
- 2.11 Compass Calibration
- 2.12 User profile
- 3. Sport Setting
- 3.1 Change Sport Mode
- 3.2 Run setting
- 3.2.1 Data Fields
- Run Alerts
- 3.2.2.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.2.2.2 Alert with upper limit and lower limit – Cadence Alert, Speed Alert, HR Alert
- 3.2.2.3 Run/Walk Alert
- 3.2.3 Auto Lap
- 3.2.4 Auto Pause
- 3.2.5 Auto Scroll
- 3.2.6 Heart Rate Monitor
- 3.2.7 ANT+ Foot Pod
- Calibrate Step Distance
- 3.2.9 Workouts
- 3.2.9.1 Interval Workouts
- 3.2.9.2 Custom Workout
- 3.3 Bike Setting
- 3.3.1 Bike Details
- 3.3.2 Speed / Cadence
- 3.3.3 Data Fields
- Bike Alert
- 3.3.4.1 Cycle Alert: Time Alert、Distance Alert、and Calories Alert
- 3.3.4.2 Alert with upper limit and lower limit – Cadence Alert, Pace Alert, HR Alert
- Auto Lap
- Auto Pause
- Auto Scroll
- Heart Rate Monitor
- Other Bikes
- Workouts
- Pace/Speed
- Countdown Timer
- Start Bike sport / training
- 3.4 Other (Sport) Settings
- 3.5 Outdoor Swim
- 3.6 Indoor Swim
- 3.7 Multi Sport
- 4. Datalog
- 4.1 Read Datalog
- 4.2 Check summary for each sport mode
- 4.3 Check Memory Details
- 4.4 SHOU-orbit website
- GPS function
- 5.1 GPS ON/OFF
- 5.2 To mark position
- 5.3 Guiding by GPS to the stored location.
- 5.4 Edit or delete the stored location
- 5.5 Back to Start
- 5.6 Stop Nanigation
- 5.7 Check GPS Satellites status
- 6. Bluetooth
- 7. Notification
- 7.1 Features
- 7.2 Operation procedure
- 8. Tempo Meter
- 9. Update Firmware (Operation System)
- 9.1 Download the new version of Firmware
- 9.2 Update Firmware (Operation System)
- 10. Important FCC notice:
Lap Press Only：Select Lap Press Only to trigger the lap counter every
timewhen you select [LAP]and pass any of those positions again.
Start and Lap：Select Start and Lap to trigger the lap counter at the GPS
location where you select [START],and at any location during the run where
you select [LAP].
Mark and Lap：Select Mark and Lap to trigger the lap counter at a specific
GPS location marked before the run (use Mark Position) and at any location
during the run where you select [LAP].
3.2.4 Auto Pause
★Note：
1. The paused time is not saved with your history data.
2. Auto Pause function is not available in Interval, customized training and swim
mode.
You can use Auto Pause to pause the timer automatically when you stop moving or
when your speed drops below a specified value. Ex: Waiting for the traffic light.
1. Select〔MODE〕to the menuChoose「Settings」Choose「Run Settings」 (Bike
settings will display in the Bike Mode, Other Settings will display in the Other
Mode.) Choose「Auto Pause」.