User Manual
STATEMENT
RFEXPOSURE
This device complies with FCC RF and Industry Canada
radiationexposurelimitssetforthforgeneralpopulation.
This device must be installed to provide a separation
distance of at least 20cm from all persons and must not
be co‐located or operatingin conjunction with any other
antennaortransmitter.
FCCSTATEMENT
Theuser’smanualorinstructionmanualforanintentional
or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authoritytooperatetheequipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B di
gi
tal device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmfulinterferenceinaresidentialinstallation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction, may cause har
mful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception
which can be determined by turning the equipment off
and on, the user is encouraged to try to co
rrect
interferencebyon
eormoreofthefollowingmeasures:
‐Reorientorrelocatethereceivingantenna.
‐ Increase the separation between the equipment and
receiver.
‐Connecttheequipmentintoanoutletoncircuitdifferent
fromthattowhichthereceiverisconnected.
‐Consultthedealeroranexperiencedradio/TVtechnician
forhel
p
.
Labelingrequirements.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
ICSTATEMENT
RSSGen/TransmitterAntenna.
Under Industry Canada regulations,this radio transmitter
may only operate using an antenna of a type and
maximum(orlesser)gainapprovedforthetransmitterby
IndustryCanada.Toreducepotentialradiointerferenceto
other users, the antenna type and its gain should be so
chosen that the equivalen
t isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementationd'IndustrieCanada,le
présentémetteurradiopeutfonctionneravecuneantenne
d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de
réduire les ri
sques de brouillage ra
dioélectrique à
l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
RSSGen/User ManualNoticeforLicence‐ExemptRadio
Apparatus.
Thisdeviceco
mplieswithIndus
tryCanadalicense‐exempt
RSSstandard(s).Operation issubjecttothefollowingtwo
conditions:(1)thisdevicemaynotcauseinterference,and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux apparei
ls ra
dio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:(1)l'appareilnedoitpasproduiredebrouillage,
et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est
susceptibled'encompromettrelefonctionnement.
RADIO
Conformément àlaréglementationd'Industrie Canada, le
présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduireles risques de brouillageradioélectrique à
l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorteque la pui
ssance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
NORMESCEM(radio)
CE
‐ETSI EN 300220-(V2.3.1-2010/02) and ETSI EN 300220-1
(V2.3.1-2010/02)
‐EN50371(20
02)
‐ETSI EN 301489‐1 (V1.8.1‐2008/4) etETSIEN 301489‐3
(V1.4.1‐2002108)
CANADA
‐RSS‐210Issue7‐Jun2007‐RSS‐GenIssue2‐Jun2007
FCC
‐FCCPart15,SubpartC15.247
‐ANSIC63.4(2009)
DÉCLARATIONDECONFORMITÉ
FR ‐ Le produit est destiné à fonctionner dabs un regard
fermé,hermétiqueauxrayonsUV.‐EtanchéitéIP68.
EN‐The device shall be placed on a closed valve box,
isolatedfromUV.‐IP68sealing
ES‐El producto està pensado para operar en un sitio
cerradoyherméticoalosrayosUV.‐EstanqueidadIP68
ConformémentàlaDirectiveEuropéenne2002/96/CEetà
lanormeEN50419:2005,cetéquipementne
doit pas être jeté avec les ordures
ménagères.
Il doit faire l’objet d’une collecte sélective
appropriée afin de permettre sa
valorisation.Parcegeste,vouscontribuerez
au respect de l’environnement et à la protection des
ressourcesnaturelles.