User Guide

ManualsBrandsSOLAX POWER ManualsStorage InverterSolaX Power X3-Hybrid 5.0KW-15.0KW Three Phase Hybrid Battery Storage Inverter

Table Of Contents

PV Connection

Grid and Oﬀ-grid Connection

Tool Preparation

Quick Installation Guide

X3-Hybrid G4

series inverter

Bracket

Waterproof cover*1

PV terminal

(positive*3 , negative*3 )

Communication line

adapter*3

(Meter/COM/BMS)

RJ45 terminals*5

10AWG Euopean

terminals*12

(Expansion bolt ,Gasket,

Self-tapping bolt)*5

PV pin angle

(positive*3 , negative*3 )

Warranty Card*1

Manual*1

OT terminal*1

M5 inner hexagon bolt*1

CT*1(Optional)

Battery pin angle *1

Hammer drill（Bit Φ10)

Socket wrench set(Hexagon)

(Crosshead M5)Torque screwdriver

Diagonal pliers

Utility knife

Diagonal pliers

Rubber hammer

OT terminals press clamp

(0.5~6mm²)

Tape ruler

Euro terminal crimping tool

Hexagon keys

Spirit level

a ) Use a marker to mark drilling holes of the

bracket on the wall.

d ) The bracket is aligned with the screw uses

the inner hexagonal wrench to screw the

tapping screw until the expansion bolt

"bang" is heard.

65.

00 mm

c) Insert expansion bolt into the hole, use

rubber hammer to knock the expansion

screw bolt into the wall.

f) Use the inner hexagonal wrench to tighten

the inner hexagonal screw on the right side of

the inverter.

e) Hang the buckle on the inverter to the

corresponding position of the backplane.

7.0mm

Step 1. Turn off the DC switch, connect the PV module, prepare a

12AWG PV cable, and find the PV (+) terminal and PV (-) terminal in

the package.

Step 2. Use a wire stripper to strip the 7mm insulation layer of the wire

end.

Wire stripper

฀

Step 4. Tighten the fastening head and into insert the corresponding positive and negative (PV-/PV+) ports of the inverter.

Note: Before inserting the PV terminal, please turn on the switch of the PV module, and use a multimeter to measure the positive and

negative poles of the PV terminal port to prevent reverse connection

Crimping Tool

Negative

Positive

Battery Connection

Step 1. Prepare a Grid cable (five-core wire) and an Off-grid cable (four-core wire), and then find the European terminal and waterproof cover in the

accessory bag.

Step 2: First remove the waterproof housing plug, The GRID and Off-grid cables go through the corresponding GRID and Off-grid ports of the

waterproof cover. Remove the 12mm insulation layer at the end of the wire. Insert the European-style terminals respectively, and make sure that

the stripped ends are inserted into the European-style terminal, and use crimping pliers to press tightly. And locked in the Grid and off-Grid ports

respectively. Finally, lock the waterproof cover screw.

High voltage lithium battery

CAN/RS485

Power line connection

Communication line connection

... ...

Note:

When using SolaX batteries, it is

recommended that the number

of battery control (T-BAT-5.8) is 1

and the number of battery modules

(HV11550) is 2-4; the number of battery control (MC0600) is 1 and the

number of battery control (HV10230) is 2-4 pcs.

8 AWG

Crimping Tool

Step 2. Insert the stripped cables into the DC plug (-) and DC Plug (+) respectively.

Step 3. Press down on the spring by hand, you can hear a click sound, then push the

ends together, and tighten the screw joints.

Step 1. Prepare 8 AWG battery power line, find the DC

plug (+), DC plug (-) in the accessory bag.

Step 4. Insert the battery power lines into the corresponding BAT port (+), (-) of the

inverter.

Note!

After the BMS communication between the battery

and the inverter is finished, the battery will work

normally.

Quick Installation Guide

X3-Hybrid 5.0KW-15.0KW

Packing List

Mounting Steps

Marker

Note: “ ”attachments are not included in the M series inverter attachment package and will be included in the X3-Matebox.

☆

“  ” The inverter in Australia needs to be connected to DRM, which is 1 more communication line adapter than that in other countries.



is the standard accessory in the M-series inverter and the optional accessory in the D-series inverter.

"▲"

☆

X3-Hybrid Series 5.0KW-15.0K W

b) Drill holes at marked spots with depth of 65mm.

PV cable

PV pin

Negative terminal

Positive terminal

Positive PV pin

Negtive PV pin

Step 3. The PV connector is divided into 2 parts, to the plug and the fastening head. Pass the cable through the fastening head and the alignment

plug .Note that the red and black lines correspond to diﬀerent pairs of plugs. Finally, force the cable into the plug and hear a "click" to indicate that

the connection is complete.

Positive metal

terminal

Negative metal

terminal

Positive terminal

Negative terminal

10AWG Euro Terminal*10

Waterproof cover

10AWG Grid(five-core wire)

Battery connection diagram:

Diagonalpliers

BAT plug (+) BAT plug (-)

Power line

DC plug (-) DC plug (+)

Spring

Cavity

The cable must pass through here

Spring

Note: BAT port, not PV port!

Note: The positive and negative

wires of the battery are not

allowed to be reversed!

☆

Multimeter

DC Voltage range ≥1100 V DC

Grid Cable and Micro-breaker recommended

Cable (copper)

Micro-Breaker

Model

X3-Hybrid-5.0-D

X3-Hybrid-5.0-M

X3-Hybrid-6.0-D

X3-Hybrid-6.0-M

X3-Hybrid-8.0-D

X3-Hybrid-8.0-M

X3-Hybrid-10.0-D

X3-Hybrid-10.0-M

Off-grid Cable and Micro-breaker recommended

Cable (copper)

Micro-Breaker

Model

X3-Hybrid-5.0-D

X3-Hybrid-5.0-M

X3-Hybrid-6.0-D

X3-Hybrid-6.0-M

X3-Hybrid-8.0-D

X3-Hybrid-8.0-M

X3-Hybrid-10.0-D

X3-Hybrid-10.0-M

X3-Hybrid-12.0-D

X3-Hybrid-12.0-M

X3-Hybrid-12.0-D

X3-Hybrid-12.0-M

Hammer

(Torque :2.5±0.2N·m)

Expansion bolts,

Tapping screws,

nut, Gasket,

Inner hexagonal wrench

(Torque :1.5±0.1 N·m)

PV 2+

Pv1+

PV1-

PV 2-

PV1+

Off-gr id

X3-Hybrid-15.0-D

X3-Hybrid-15.0-M

X3-Hybrid-15.0-D

X3-Hybrid-15.0-M

20A

32A

40A

40A 40A

4~6mm²

4~6mm² 5~6mm²

5~6mm²

4~6mm²

16A

20A

25A

32A 40A

4~6mm²

4~6mm² 4~6mm²

4~6mm²

Grid

Off-grid

Crimping Tool

L=12mm

L=1

2mm

Diagonal pliers

Torque screwdriver

( Torque: 0.7±0.1N·m)

Positive PV pin

Negtive PV pin

Multimeter

DC Voltage

Range ≥1100 V DC

☆

▲

*The PV port wiring of X3-Hybrid G4 M series inverter has been completed. For specic installation details, please refer to the X3-

Matebox Quick Installation Guide, the D series needs to be wired according to the following steps.

Diagram A: N line and PE line separate wiring, D series inverter;

(For most countries)

BAT

Battery

N-BAR for loads

N-BAR for oﬀ-grid loads

oﬀ-grid loads

Loads

X3-Hybrid G4

PV 1

PV 2

E-BAR

RCD

Breaker

Grid

Breaker

Grid

Oﬀ-grid

Main Breaker/RCD

Breaker

Distribution Box

Diagram B: N line and PE line separate wiring, M series inverter;

(For most countries)

Diagram C: N line and PE line together, D series inverter;

( Applicable to Australia)

BAT

Battery

N-BAR for loads

N-BAR for oﬀ-grid loads

oﬀ-grid loads

Loads

X3-Hybrid G4

PV 1

PV 2

E-BAR

RCD

Breaker

Grid

Breaker

Grid

Oﬀ-grid

Main Breaker/RCD

Breaker

Distribution Box

CT 1

CT 2

CT 3

Diagram D: N line and PE line together, M series inverter;

( Applicable to Australia)

* The Grid and the Off-grid ports of X3-Hybrid G4 M series inverter have been connected, for specific installation details, please refer to the

X3-Matebox Quick Installation Guide .and the D series needs to be wired according to the following steps.

*Battery port connection line of the X3-Hybrid G4 M series

inverter is on the X3-Matebox,for specific installation details,

please refer to the X3-Matebox Quick Installation Guide It is

necessary to wire the D series according to the following steps.

Pocket WiFi 1(Optional)*

BAT

Battery

N-BAR for loads

N-BAR for oﬀ-grid loads

oﬀ-grid loads

Loads

X3-Hybrid G4

PV 1

PV 2

E-BAR

Grid

Oﬀ-grid

Main Breaker/RCD

Breaker

CT 1

CT 2

CT 3

X3-Matebox

E-BAR

X3-Matebox

BAT

Battery

N-BAR for loads

N-BAR for oﬀ-grid loads

oﬀ-grid loads

Loads

X3-Hybrid G4

PV 1

PV 2

E-BAR

Grid

Oﬀ-grid

Main Breaker/RCD

Breaker

Note: The RCD on the gure represents a leakage protection device with a circuit breaker function.

com

※Note: Please press

European terminal into

a 3.3.*3.3mm square.

Hexagon keys

( Torque: 1.2±0.2N·m)

Meter 1*

10AWG Off-grid((four-core wire)

Multifunction terminal crimping

tool (RJ45)

Non-polar

DC MCB

Φ8 Hammer

drill

Click !

X3-Hybr id S er ie s

User Manu al

5.0kW - 15.0kW

Summary of content (2 pages)

PAGE 1
Tool Preparation Multimeter Hammer drill（Bit Φ10) Quick Installation Guide X3-Hybrid 5.0KW-15.0KW OT terminals press clamp (0.5~6mm²) Utility knife Diagonal pliers Hexagon keys Rubber hammer Crimping Tool Marker Tape ruler Euro terminal crimping tool Spirit level Mounting Steps a ) Use a marker to mark drilling holes of the bracket on the wall. b) Drill holes at marked spots with depth of 65mm. c) Insert expansion bolt into the hole, use rubber hammer to knock the expansion m 6 5 .
PAGE 2
x Communication Connection(BMS/Meter/CT/COM/DRM) Grounding Connection(manodatory) * The ground wire port of X3-Hybrid G4 M series inverter has been connected, and the D series needs to be wired according to the following steps. Electric meter connection diagram Ø COM PIN Definition COM 1 8 1 3 2 Drycontact_A(in) Drycontact_B(in) 5 4 6 +13V 485A 485B 7 8 Step 1. Prepare a one-core cable (12AWG), and then find the ground terminal in the accessories. Step 4.