TP Series - Triple or Quad PV Top of Pole Solar LED Lighting System Installation Manual MKTG-TP34-02-EN-1113
Installation Manual | TP Series Important Notes and Warnings This installation and instruction manual provides installation instructions for the Sol TP Series solar LED lighting systems. The entire contents of this manual should be thoroughly reviewed and understood prior to installing this equipment. Do not discard this manual, as it contains complete installation instructions. To insure proper operation of this equipment, it is important that the equipment be utilized for its intended use.
Installation Manual | TP Series Parts Provided Solar Panels - 3 or 4 Fixture Assembly -Cobrahead or Shoebox Z Rails Battery Enclosure Top of Pole Triple/ Quad Bracket Tenon Adaptor Light Fixture Harness (1 or more) TPM Mount Fastener Set A (4-8) Controller Tenon Fastener Set B (3) Tenon Fastener Set C (3) Battery Harness Battery Enclosure Channel Fastener Set D (2) PV Panel Harness Batteries (1, 2 or 3) Battery Cables (1 per battery) Battery Enclosure Channel Fastener Set E (4) Fastener Set F (2
Installation Manual | TP Series 1.0 Positioning the Light 2.0 Assembling 2.1 PV Panel Assembly - Triple or Quad Panels. Lay PV panels side by side on cardboard packaging to protect surface. TP Mounting Bracket Kit 410016-100 a 6X Note: Keep bolts loosely fastened until PV panels are secured.
Installation Manual | TP Series Orientation of PV J-boxes should be at top end of panel b 16X TP Mounting Bracket Kit 410016-100 2.2 Connect PV Harness ( if panels have a panel pan, harness will already be connected).
Installation Manual | TP Series b 7 MKTG-IM-TP34-02-EN-1113
Installation Manual | TP Series 2.
Installation Manual | TP Series 2.4 Place Solar Panel Assembly on the Pre-Buried Pole - Maximum Pole Height should be 4 feet above ground a PV Modules always face EQUATOR (South in Northern Hemisphere) EQUATOR 2.5 Match Drill Hole in Tenon with Tenon Adaptor and Secure.
Installation Manual | TP Series 2.6 Drill Battery Mounting & Access Holes; Route PV Harness a 6” Min. from top of pole 4.25” below Access hole for PV Harness. Drill thru one side @ 1.25” Dia. 28” For dual Battery Enclosures drill thru pole. Battery Enclosure Channel holes: Drill thru @.87 Dia. Note: Battery enclosure may be mounted lower than shown.
Installation Manual | TP Series 2.7 Drill Arm Mounting & Access Holes; Route Fixture Harness a Arm Mounting Hole. Drill thru 2x @.75”Dia. Access hole for Luminaire harness. Drill thru one side @ 1.25” Dia. Note: If mounting two arm mounts, connect both using the same bolts.
Installation Manual | TP Series 2.8 Secure Battery Enclosure Channel to Pole PV Harness Fastener Set D 2x 3/4-10 x 12” bolts Fastener Set E 4x 1/4”–20 x 1/2” hex head bolts/washers Luminaire Harness Note: Before attaching Battery Enclosure Channel, fish Luminaire Harness down pole through access hole for arm. 2.
Installation Manual | TP Series 2.10 Mount Arm on the Pole a Note: Fish Luminaire Harness through arm before attaching. 2.
Installation Manual | TP Series 2.12 Mount the Light Fixture on the Arm-Shoebox b Hex key and screws 2.
Installation Manual | TP Series 2.
Installation Manual | TP Series 2.
Installation Manual | TP Series 2.16 Test a 2.
Installation Manual | TP Series In-Warranty Service Instructions A Returned Merchandise Authorization (RMA) number must be obtained from Sol Inc. before equipment can be returned for repair or replacement under warranty.
Sol Inc. | 3210 SW 42nd Avenue | Palm City, Florida 34990 www.solarlighting.com E-mail support: support@solarlighting.com Phone: +1.772.286.9461 | Toll: 800.959.1329 (USA & Canada) Fax: +1.772.286.9616 Office Hours: Monday - Friday: 8:30 am to 5:00 pm (EST) © 2013 Sol Inc.
