(EN) INSTRUCTION Escape Robot Kit www.sol-expert-group.
(EN) Escape Robot - Kit 10+ 1. Product Introduction: SOL-EXPERT group The Escape Robot Kit works just like an A.I. robot. It never fails to find its way out of a maze. The Escape Robot makes use of three infrared emitting diodes and one infrared receiving module to send and receive signals and detect obstacles. Escape Robot has an in-built microprocessor which enables it to "think" on its own, as it process information about its environment and maneuvers itself around obstacles.
Pins Slide Switch Infrared Receiving Module Qty Qty Qty 4 pcs 1pc 1 pc Battery Holder Printed Circuit Board Qty R14 1 pc M M1 K LED3 R8 R5 21-886 R1 IR_RX_MOD C5 K R7 LED2 R17 IR_RX_MOD R10 Q13 Q14 C1 R13 Q2 ZD1 R18 Q7 Q11 LED4 Q3 R11 R15 M 1 pc C2 C3 C4 BZ1 BAT.
Description Part I.D. Qty 1 pc Zener Diode 3.9V ZD1 Step 2: Mount and soldering the components such as Ceramic capacitor, Electrolytic capacitor, Transistor, Oscillator. Description Part I.D. Qty C2,C3 Ceramic Capacitor 30 2 pcs C1 Ceramic Capacitor 103 1 pc C4 Ceramic Capacitor 104 1 pc C5 Ceramic Capacitor 224 1 pc Description Part I.D.
Step 5: Mount and soldering Infrared Receiving Module. Description Part I.D. Qty 1 pc Infrared Receiving Module IR_RX_MOD Remark: Bottom Layer 21 IR_ -88 6 RX _M OD IR_RX_MOD PCB PAD 21 -8 IR_R 86 X_M OD PCB 6. Mechanical Assembly: 1 Assemble the gearbox first before go ahead for this section. (Refer to the gearbox instruction manual.) 2 Toward the shaft of motor to the same way as below drawing to solder wires and ceramic capacitor.
4 PCB & Gearbox Assembly Orange P5 x4 Green Blue Orange Blue Yellow Yellow Green 5 Note： The yellow and green wires must be at front (toward the same way as infrared emitting diodes).
. How it works: 1. Switch power to "ON". The LED 1 will light up and the unit will emit 3 beeps as it starts running. 2. When the unit starts running, the emitting diodes LED2, LED3 and LED4 will send out signals sequentially to detect obstacles along its path. Once an obstacle has been detected, the signal received will be transmitted to the receiving module which will then instruct the Escape Robot to take evasive actions.
SIX-LEG WALKING TYPE GEARBOX - Kit 10+ 1. Product Introduction: ● This gearbox works with 2 types of feet. Try the different feet and enjoy the fun they will bring you ● This set contains 2 motors,gears,and all necessary parts ● Output speed: 170 RPM ● Easy to assembly !WARNING! Keep the adress of the company Not suitable for children under 3 years. Contains small parts! 0-3 2. Tools You May Need: 3.
4. Mechanical Assembly: 2 1 P5 x2 P1 x2 90 F "F" must be set in "G" vertically. G P9 x2 3 P12 P3 x4 P2 x2 P4 x4 P12 4 1. 2. - 20 - 3.
5 7 P5 x4 A x2 P6 x2 B x2 P5 x4 6 8 P10 P5 x4 P11 D D P6 x4 P7 P11 Keep the two ears of the shaft (P7) to be horizontal to the base.
9 Keep the two ears of the shaft (P8) to be horizontal to the base.
