T Spec. No Doc No Version Date PL905293F/3.2V PQ-AR&D-SPC-L612 00 2014-1-7 聚合物锂离子电池 产品承认书 Li-ion Polymer Cell Specification For Approval Model:PL905293F/3.2V Registered Checked Approved 客户确认（Customer confirmation） 客户名称/印章 Messrs/Seal 客户确认人 Confirmed 厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD. 中国福建省厦门市集美北部工业区宝龙工业园 Powerlong Industrial District, Northern Industrial Zone,Jimei,Xiamen,Fujian,China Tel: 86-592-6103999 Fax: 86-592-6102721 Http://www.pl-battery.com.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD Revision record 修订记录 1. A temporary version 临时版本：PQ-AR&D-SPC-L612 2.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 目录 1. Scope 适用范围 .............................................................................................1 2. Initial Dimension 产品尺寸 .....................................................................1 3. Specification 产品规格 .............................................................................1 4. Appearance 产品外观 ...................................................................................2 5.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 1. Scope 适用范围 This specification describes the basic performance, technical requirement testing method, warning and caution of the lit ihium ion Polymer rechargeable battery .The specification only applies to《General specification of lithium-ion cells and batteries for mobile phone》 GB/T 18287-2013。 本规格书规定了聚合物锂离子电池的基本性能、技术要求、测试方法及注意事项。本规格书 参照《移动电话用锂离子蓄电池及蓄池组总规范》GB/T 18287-2013 制定。 2.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 3.13 Initial Impedance 初始内阻 3.14 Weight 重量 3.15 Operating temperature 工作温度 ≤60mΩ 3.65V,AC 1KHz measured Approx 73g Charging 充电：0℃~45℃ Discharging 放电：‐10℃~60℃ 4. Appearance 产品外观 There shall be no such defect as scratch, flaw, crack, rust, leakage, which may adversely affect commercial value of battery. 电池外表面清洁，无电解液泄漏，无明显的划痕及机械损伤，无变形，无影响电池价值的其 它外观缺陷。 5. Test Requirement 测试要求 5.1.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 6. Electrical Characteristics 电气性能 Item项目 Test Methods and Condition 测试方法和条件 Criteria 标准 0.2ItA Capacity 0.2ItA 容量 After standard charging, laying the battery 0.5~1.0h, At 23℃±2℃ ambient temperatures，then discharging at 0.2 ItA to ending voltage, recording the discharging time. 标准充电后,搁置0.5~1.0h,在23℃±2℃的环境温度下， 然后用0.2ItA恒流放电至终止电压,记录放电时间。 ≥5h 6.2 1ItA Capacity 1ItA 容量 After standard charging, laying the battery 0.5~1.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 6.6 Afterstandardcharging,At20℃±5℃ambient temperature, the electrical core open shelved after 28d, at 23±2℃ ambient temperature to 0.2ItA voltage discharge to the deadline, record the discharge time, and then the standard charge,at23 ± 2 ℃ ambient temperature to 0.2ItA discharge to the deadline voltage, discharge time record. 标准充电后，在20℃±5℃的环境温度下，电芯开路搁 置28d后，在23℃±2℃的环境温度下以0.2ItA放电至终 止电压，记录放电时间，然后再标准充电后，在23℃ ±2℃的环境温度下以0.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 7.2 7.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 8.3 8.4 8.5 Over‐charge 过充电 Batteries 0.2ItA discharge to the termination voltage, connect the battery positive and negative with the power to regulate the current to the 3ItA, charged to 4.6V. Meet either of the following two situations can be stopped: 电池以0.2ItA进行放电至终止电压，连接电池正负极 与电源，调节电流至3ItA，充电至4.6V。满足以下两 种情况任一种即可停止： a) the battery charging time to achieve sustained 7h.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 8.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 电池的保质期从出货之日算起为壹年。如果证明电池的缺陷是在我们公司制造过程中造成的而不是 客户滥用或错误使用造成，本公司负责退换电池。 13. Matters needing attention 注意事项 1) Do not submerge the battery in water, do not wet the battery when store the battery. 禁止将电池放入水中，保存过程中应放置在阴凉干燥的环境中。 2) Do not use the battery direct sunlight , may cause battery overheating then fire or invalidation. 禁止在灸热的阳光下使用，可能会引起电池过热、起火或功能失效。 3) Never remove, open, chopped or metal piercing the cell or battery.
厦门宝龙工业股份有限公司 XIAMEN POWERLONG INDUSTRY JOINT-STOCK CO., LTD 14. Others 其它事项 1) The customer is requested to contact POWERLONG in advance, if and when the customer needs other applications or operating conditions than those described in this document. Additional experimentation may be required to verify performance and safety under such conditions.
